• Journal of Sensor Science and Technology
• /
• v.1 no.2
• /
• pp.147-154
• /
• 1992

This paper describes the design of implantable 8-channel telemetering system to get physiological signals. The internal circuits of this system are designed not only to achieve as small size and low power dissipation as possible, but also to enable continuous measurement of physiological signals. Its main functions are to enable continuous measurement of physiological signals and to accomplish on-off power switching of an implantable battery by receiving appropriate command signals from an external circuit. To integrate implantable biotelemetry system, we performed layout of internal system using Lambda based $2{\mu}m$ n-well design rules. This system, used together with appropriate sensors, is expected to be capable of measuring and transmitting such significant parameters as pressure, pH, and temperature.

• Journal of Sensor Science and Technology
• /
• v.15 no.6
• /
• pp.397-405
• /
• 2006

Single crystal $AgGaSe_{2}$ layers were grown on thoroughly etched semi-insulating GaAs(100) substrate at $420^{\circ}C$ with hot wall epitaxy (HWE) system by evaporating $AgGaSe_{2}$ source at $630^{\circ}C$. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of single crystal $AgGaSe_{2}$ thin films measured with Hall effect by van der Pauw method are $4.05{\times}10^{16}/cm^{3}$, $139cm^{2}/V{\cdot}s$ at 293 K, respectively. The temperature dependence of the energy band gap of the $AgGaSe_{2}$ obtained from the absorption spectra was well described by the Varshni's relation, $E_{g}(T)$=1.9501 eV-($8.79{\times}10^{-4}{\;}eV/K)T^{2}$/(T+250 K). The crystal field and the spin-orbit splitting energies for the valence band of the $AgGaSe_{2}$ have been estimated to be 0.3132 eV and 0.3725 eV at 10 K, respectively, by means of the photocurrent spectra and the Hopfield quasicubic model. These results indicate that the splitting of the ${\Delta}So$ definitely exists in the ${\Gamma}_{5}$ states of the valence band of the $AgGaSe_{2}$. The three photocurrent peaks observed at 10 K are ascribed to the $A_{1}-$, $B_{1}-$, and $C_{1}-$exciton peaks for n=1.

• Journal of Sensor Science and Technology
• /
• v.14 no.3
• /
• pp.160-168
• /
• 2005

ZnO epilayer were synthesized by the pulesd laser deposition(PLD) process on $Al_{2}O_{3}$ substrate after irradiating the surface of the ZnO sintered pellet by the ArF(193 nm) excimer laser. The epilayers of ZnO were achieved on sapphire ($Al_{2}O_{3}$) substrate at a temperature of $400^{\circ}C$. The crystalline structure of epilayer was investigated by the photoluminescence. The carrier density and mobility of ZnO epilayer measured with Hall effect by van der Pauw method are $8.27{\times}1016cm^{-3}$ and $299cm^{2}/V{\cdot}s$ at 293 K, respectively. The temperature dependence of the energy band gap of the ZnO obtained from the absorption spectra was well described by the Varshni's relation, $E_{g}(T)$=3.3973 eV-($2.69{\times}10^{-4}$ eV/K)$T^{2}$/(T+463K). The crystal field and the spin-orbit splitting energies for the valence band of the ZnO have been estimated to be 0.0041 eV and 0.0399 eV at 10 K, respectively, by means of the photocurrent spectra and the Hopfield quasicubic model. These results indicate that the splitting of the ${\Delta}so$ definitely exists in the ${\Gamma}_{6}$ states of the valence band of the ZnO. The three photocurrent peaks observed at 10 K are ascribed to the $A_{1}-$, $B_{1}-$, and $C_{1}-$exciton peaks for n = 1.

• Korean Journal of Soil Science and Fertilizer
• /
• v.50 no.5
• /
• pp.336-344
• /
• 2017

The soil water characteristics curve (SWCC) represents the relation between soil water potential and soil water content. The shape and range of SWCC according to the relation could vary depending on soil characteristics. The objective of the study was to estimate SWCC depending on soil types and layers and to analyze the trend among them. To accomplish this goal, the unsaturated three soils were considered: silty clay loam, loam, and sandy loam soils. Weighable lysimeters were used for exactly measuring soil water content and soil water potential. Two fitting models, van Genuchten and Campbell, were applied. Two models entirely fitted well the measured SWCC, indicating low RMSE and high $R^2$ values. However, the large difference between the measured and the estimated was found at the 30 cm layer of the silty clay loam soil, and the gap was wider as soil water potential increased. In addition, the non-linear decrease of soil water content according to the increase of soil water potential tended to be more distinct in the sandy loam soil and at the 10 cm layer than in the silty clay loam soil and at the lower layers. These might be seen due to the various factors such as not only pore size distribution, but also cracks by high clay content and plow pan layers by compaction. This study clearly showed difficulty in the estimation of SWCC by such kind of factors.

• Journal of the Korean Ceramic Society
• /
• v.54 no.3
• /
• pp.243-248
• /
• 2017

Pd-doped $SnO_2$ thick film with a pure tetragonal phase was prepared on patterned Pt electrodes by an ink dropping method. Nanostructured $SnO_2$ powder with a diameter of 10 nm was obtained by a modified hydrazine method. Then the ink solution was fabricated by mixing water, glycerol, bicine and the Pd-doped $SnO_2$ powder. When the Pd doping concentration was increased, the grain size of the Pd-doped $SnO_2$ thick film became smaller. However, an agglomerated and extruded surface morphology was observed for the films with Pd addition over 4 wt%. The orthorhombic phase disappeared even at a low Pd doping concentration and a PdO peak was obtained for a high Pd doping concentration. The crack-free Pd-doped $SnO_2$ thick films were able to successfully fill the $30{\mu}m$ gap of the patterned Pt electrodes by the optimized ink dropping method. The prepared 3 wt% Pd-doped $SnO_2$ thick films showed monoxide gas responses ($R_{air}/R_{CO}$) of 4.0 and 35.6 for 100 and 5000 ppm, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.701-709
• /
• 2011

In semiconductor wafer fabrication, etching is one of the most critical processes, by which a material layer is selectively removed. Because of difficulty to correct a mistake caused by over etching, it is critical that etch should be performed correctly. This paper proposes a new approach for etch endpoint detection of small open area wafers. The traditional endpoint detection technique uses a few manually selected wavelengths, which are adequate for large open areas. As the integrated circuit devices continue to shrink in geometry and increase in device density, detecting the endpoint for small open areas presents a serious challenge to process engineers. In this work, a high-resolution optical emission spectroscopy (OES) sensor is used to provide the necessary sensitivity for detecting subtle endpoint signal. Partial Least Squares (PLS) method is used to analyze the OES data which reduces dimension of the data and increases gap between classes. Support Vector Machine (SVM) is employed to detect endpoint using the data after PLS. SVM classifies normal etching state and after endpoint state. Two data sets from OES are used in training PLS and SVM. The other data sets are used to test the performance of the model. The results show that the trained PLS and SVM hybrid algorithm model detects endpoint accurately.

• Journal of Sensor Science and Technology
• /
• v.17 no.6
• /
• pp.437-446
• /
• 2008

Single crystalline ${ZnIn_2}{Se_4}$ layers were grown on thoroughly etched semi-insulating GaAs (100) substrate at $400^{\circ}C$ with hot wall epitaxy (HWE) system by evaporating ${ZnIn_2}{Se_4}$ source at $630^{\circ}C$. The crystalline structure of the single crystalline thick films was investigated by the photoluminescence (PL) and Double crystalline X-ray rocking curve (DCRC). The carrier density and mobility of ${ZnIn_2}{Se_4}$ single crystalline thick films measured from Hall effect by van der Pauw method are $9.41{\times}10^{16}cm^{-3}$ and $292cm^2/V{\cdot}s$ at 293 K, respectively. The temperature dependence of the energy band gap of the ${ZnIn_2}{Se_4}$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)$=1.8622 eV-$(5.23{\times}10^{-4}eV/K)T^2$/(T+775.5 K). After the as-grown ${ZnIn_2}{Se_4}$ single crystalline thick films was annealed in Zn-, Se-, and In-atmospheres, the origin of point defects of ${ZnIn_2}{Se_4}$ single crystalline thick films has been investigated by the photoluminescence (PL) at 10 K. The native defects of $V_{Zn}$, $V_{Se}$, $Zn_{int}$, and $Se_{int}$ obtained by PL measurements were classified as a donors or acceptors type. And we concluded that the heat-treatment in the Se-atmosphere converted ${ZnIn_2}{Se_4}$ single crystalline thick films to an optical p-type. Also, we confirmed that In in ${ZnIn_2}{Se_4}$/GaAs did not form the native defects because In in ${ZnIn_2}{Se_4}$ single crystalline thick films existed in the form of stable bonds.

• Journal of Sensor Science and Technology
• /
• v.5 no.5
• /
• pp.1-10
• /
• 1996

Solar cells made of the edge-defined film-fed growth Si are characterized using current-voltage, surface photovoltage, electron beam induced current, electron microprobe, scanning electron microscopy, and electron backscattering. The weak temperature dependence of the I-V curves in the EFG solar cells is due to a voltage variable shunt resistance giving higher diode ideality factors than the ideal one. The voltage variable shunt resistance is modeled by a modified recombination mechanism which includes carrier tunneling to distributed impurity energy states in the band gap within the space-charge region. The junction integrity and the substrate quality are characterized simultaneously by combining I-V and surface photovoltage (SPV) measurements. The diode ideality factors and the surface photovoltages characterize the junction integrity while the SPV diffusion lengths characterizes the substrate quality. Most of the measured samples show the voltage variable shunt resistance although how serious it is depends on the solar cell efficiency. The voltage variable shunt resistance is understood as one of the most important factors of the degradation of EFG solar cells.

• Journal of Sensor Science and Technology
• /
• v.6 no.5
• /
• pp.414-422
• /
• 1997

CdS thin films with low resistivity and adequate transmittance in the visible region for the window of CdS/CdTe hetero junction solar cel1 were prepared by close spaced vapor transport(CSVT) method. The electrical and optical properties of the CdS thin films were investigated in terms of the deposition conditions, such as the substrate temperature, the working pressure, and the source temperature. The substrate temperature, the working pressure, and the source temperature for the optimum deposition of the CdS thin films were $300^{\circ}C$, 100mTorr, and $730^{\circ}C$, respectively. The resistivity and the transmittance of the CdS thin films deposited under this condition were about $7.21{\times}10^{3}{\Omega}cm$ and over 65%, respectively. The crystallinity, the resistivity, and optical band gap were improved greatly compared to the CdS thin films deposited by general high vacuum evaporation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.1555-1562
• /
• 2015

Metal oxide semiconductors have been applied in several areas, such as solar cells, sensor, optical elements and displays, due to the high surface area, unique electrical and optical characteristics. Zinc oxide among the metal oxide has excellent physicochemical properties. Zinc oxide is a n-type semiconductor with a wide direct transition band gap of 3.37 eV at room temperature and large exciton binding energy of 60 meV. Cation-doped zinc oxide studies were conducted to complement the electrical and optical characteristics. In this paper, Al-doped ZnO was synthesized by hydrothermal synthesis using microwaves. ZnO was synthesized by adjusting the precursor ratio and using different dopants. The optimal ZnO synthesis conditions for crystal shape and optical properties were determined. The optical properties of aluminum doped zinc oxide were then examined by SEM, XRD, PL, UV-vis absorbance spectrum, and EDS.