• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 추계학술발표회 초록집
• /
• pp.30-31
• /
• 2000

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2003년도 추계학술발표회초록집
• /
• pp.38-39
• /
• 2003

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 1998년도 추계학술발표회 초록집
• /
• pp.8-9
• /
• 1998

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2003년도 춘계학술발표회 초록집
• /
• pp.99-100
• /
• 2003

• 대한기계학회논문집
• /
• 제12권4호
• /
• pp.747-754
• /
• 1988

본 연구에서는 우리나라 자동차업계에서 널리 사용되는 복합조직인 고장력 강 판(high strength steel sheet, HS)과 아연도금강판(galvanized steel sheet, GA)을 선택하여 각 강판간의 점용접 피로특성을 규명하기 위하여 아래와 같은 4가지 조건하 의 단점 점용접 시험편을 제작하였다.

• 한국표면공학회지
• /
• 제33권5호
• /
• pp.381-386
• /
• 2000

It was found that colloidal silica sprayed to the galvanized steel sheet apparently made the molten zinc layer solidified to be the randomly oriented fine grains. Its spraying effect was also little affected by steel temperature that had been considered as one of the major operating factors in this process. From the results of surface analysis, it is considered that aluminum dissolved in coating layer reduces silica to silicon by the oxidation-reduction reaction, and that the reduced silicon acts as a more effective nucleus in solidification reaction than phosphate salt, siica and alumina.

• Corrosion Science and Technology
• /
• 제13권4호
• /
• pp.125-129
• /
• 2014

Shinning spot defects on galvanized steel sheets were studied by optical microscope, scanning electron microscope(SEM), Energy Dispersive Spectrometer (EDS) and Laser-Induced Breakdown Spectroscopy Original Position Statistic Distribution Analysis (LIBSOPA) in this study. The research shows that the coating thickness of shinning spot defects which caused by the substrate defect is much lower than normal area, and when skin passed, the shinning spot defect area can not touch with skin pass roll which result in the surface of shinning spot is flat while normal area is rough. The different coating morphologies have different effects on the reflection of light, which cause the shinning spot defects more brighter than normal area.

• 한국표면공학회지
• /
• 제27권3호
• /
• pp.149-157
• /
• 1994

The formation of spangles on a hot dip galvanized sheet steel by spray cooling the molten zinc coating with air, water and 2.0wt% $NH_4H_2PO_4$ solution has been studied performing laboratory experiments, and their coating properties have been evaluated. Minimized spangles were easily formed by mist spraying the solution for 1 second at the low nozzle spray pressure onto the molten zinc at 420~$422^{\circ}C$ because the solute $NH_4H_2PO_4$ in the sprayed solution imparted a highly rapid cooling effect to the coating through its endothermic de-composition reactions and because the decomposed products acted as numerous nucleation sites for the mini-mized spangles on the coating. Good surface appearances sand sound coating properties were obtained on this coating. Only regular spangles were formed on the coating by the forced convective air cooling. At the high nozzle spray pressure, zero spangles were formed on the coating by the pure water spray cooling. However, the coating had a dull and rough surface with craters sand cracks.

• Journal of Welding and Joining
• /
• 제12권2호
• /
• pp.76-86
• /
• 1994

Spot welding behavior of galvanized steel has been studied using both numerical and experimental techniques. The model that used to calculate temperature distribution within weldment is two-dimensional axis-symmetric finite difference method, and nugget sizes of specimen welded in condition of welding current and time has been estimated by experiment Results have shown that nugget sizes are increased in proportion to welding current and time, but the growth rate of nugget is decreased. Shear-tensile strength tests have shown interface fracture when welding current is 7, 9KA, welding time is 8-14cycle and 11KA, 8-10cycle respectively, but above 7, 9KA fracture shows button type. In button fracture, shear-tensile strengths have been proportional to nugget sizes.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.247-249
• /
• 2005

Evaluation and prediction of fatigue crack initiation life in EZNCEN(Galvanized steel sheet) and HS40R(High strength steel sheet) tensile-shear spot weldment were studied by using DCPDM(DC Potential Drop Method)