• International Journal of Contents
• /
• v.2 no.1
• /
• pp.29-33
• /
• 2006

The common-source low noise amplifier(LNA) with inductive degeneration using a genetic algorithm is designed and tested for a down converter in an industrial, scientific and medical (ISM) band application and a wireless broadband internet service (WiBro). The genetic algorithm optimizes the reflection coefficients to be well matched the input and output ports between multistage transistor amplifiers, and it generates low voltage standing wave ratio as well as gain flatness of the amplifier. The stability and the gain flatness of the LNA have been improved by combining the matching circuits and the series feedback microstrip lines with inductive degeneration at common-source port. In the frequency range of ISM band and WiBro application operating at $2.3GHz{\sim}2.5GHz$, the measured power gain and maximum voltage standing wave ratio (VSWR) of the LNA are $41{\pm}0.5dB$ and 1.3, and the noise figure of the LNA is lower than 0.85dB. The above results are agreed well with the theoretical values of the amplifiers.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.7
• /
• pp.24-30
• /
• 2000

In this paper, we proposed an fiber-optic transceivers based on the analog optical transmission techniques of incorporating the SCM (subcarrier multiplexing) and WDM (wavelength-division multiplexing ) method, which can be used to transmission of IMT-2000 and PCS wireless frequency band and analyzed overall those parameters related with fabrication. Especially in the impedance matching network between RF signal and LD, we proposed the method of deriving optimal performance using simulation techniques. In the frequency band of 1.7GHz∼2.25GHz, experimental data for the gain flatness and the noise floor of the optical link were also presented $\pm$1.5dB and -130dBm respectively when the link Rain was 0dB.

• Journal of the Korea Knowledge Information Technology Society
• /
• v.12 no.4
• /
• pp.539-550
• /
• 2017

In this paper, we designed, fabricated and tested an UHF band cylindrical dipole array antenna. In the proposed antenna, cylindrical dipoles were vertically arranged in four stages. A parallel structure feeding circuit was installed inside the cylindrical dipole and mounted so as to be broadband matching. The feeding circuit was installed at the center of the cylindrical dipole to optimize the gain flatness characteristic of the azimuth direction omnidirectional radiation pattern. Minimizing the difference between the signals branched from the feeding circuit and realizing the symmetry of the radiation pattern. The required specifications are more than 11.2% bandwidth in UHF band, above 6dBi antenna gain, standing wave ratio of 2:1 or less, less than ${\pm}1dB$ gain flatness in azimuth radiation pattern, more than 13 degrees in elevation radiation pattern of 3dB beamwidth. We confirmed the possibility of implementation through M&S and verified the result of M&S through production and testing. The test results are 11.2% bandwidth in the UHF band, 6.30 to 8.31 dBi gain, 1.53:1 standing wave ratio or less, within ${\pm}0.2dB$ gain flatness in the azimuth radiation pattern, elevation radiation pattern of 3dB beam width was 15.62 to 15.84 degrees. The test result meets all requirements specifications.

• ETRI Journal
• /
• v.20 no.1
• /
• pp.28-36
• /
• 1998

A simple experimental method to design gain-flattened erbium-doped fiber amplifier is proposed and demonstrated based on the two linear relations between the output power and the pump power, and between the gain and the length of the eribium-doped fiber at the gain flattened state. The spectral gain variation of the eribium-doped fiber amplifiber constructed by this method was less than 0.4 dB over 12 nm (1,545~1,557nm) wavelength region. The gain flatness is also controlled within 0.4 dB over the input power range of -30~-15dBm/ch through the feedback control utilizing the amplified spontaneous emission power in the 1,530 nm region.

• Journal of the Optical Society of Korea
• /
• v.7 no.2
• /
• pp.64-66
• /
• 2003

The optical gain and noise figure improved double-pass two-stage EDFA using a mirror, circulator, and gain-flattening filters is proposed. By double passing the pump light and removing the ASE propagating into the input part, the signal gain of 5 ㏈ and noise figure of 2.1 ㏈ are improved compared to the conventional single- and double-pass EDFA With gain-fattening filters in the second stage of EDFA, we obtain an improved flat gain with a gain flatness less than 1 ㏈ over 33-nm wavelength range at the 980-nm pump power of 86 ㎽.

• Journal of the Optical Society of Korea
• /
• v.18 no.5
• /
• pp.442-448
• /
• 2014

For the first time, a novel analytical model of the net gain for a Raman-EDFA hybrid optical amplifier (HOA) is proposed and its various parameters optimized using a genetic algorithm. Our method has been shown to be robust in the simultaneous analysis of multiple parameters (Raman length, EDFA length, and pump powers) to obtain large gain. The optimized HOA is further investigated at the system level for the scenario of a 50-channel DWDM system with 0.2-nm channel spacing. With an optimized HOA, a flat gain of >17 dB is obtained over the effective ITU-T wavelength grid with a variation of less than 1.5 dB, without using any gain-flattening technique. The obtained noise figure is also the lowest value ever reported for a Raman-EDFA HOA at reduced channel spacing.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.5
• /
• pp.872-882
• /
• 1994

In this paper, the Low Noise Amplifier(LNA) is designed and fabricated to include a band pass filter characteristics considering the antenna system characteristics according to the transmitting and receiving signal level of communication satellite transponder. As an example, a 2-stage low noise amplifier and a 4-stage amplifier and designed, fabricated and measured at 14,0~14.5GHz of receiving frequency band. This fabricated LNA has shown the gain with very good flatness within pass-band, and its gain decreases rapidly out of band resulting in supperssion of the transmitting signal power leakage. It has shown the 20.3dB +- 0.1dB of pass-band gain, the 1.44dB +-0.04dB of noise figure and the 14dB rejection out of band(12.25~12.75GHz). The gain flatness, noise figure and group delay of this 2-stage LNA satisfactorily met the simulation results. And the fabricated 4-stage amplifier has shown the more than 42dB of pass-band gain, the +-0.25dB of flatness and the 28dB of the rejection effect for transmitting power leakage. The 2-stage LNA and 4-stage amplifier, in this paper, will bring a design margin for the input filter and also result in the system cost reduction.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.2 s.105
• /
• pp.95-100
• /
• 2006

In this paper, we designed amplitude equalizer which is composed of amplifier, complementary shaping filter and attenuator in order to improve flatness of high order bandpass filter. We modified Chebyshev polynomial and calculated the prototype elements for complementary shaping filters by network synthesis. The amplitude equalizer is realized that it connects the 4th order complementary shaping filter designed by using calculated the prototype elements to the amplifier compensating for insertion loss and improving return loss, and with the attenuator for gain control. Using proposed amplitude equalizer, We certificated improvement in flatness of 13th order bandpass filter at WiBro band.

• Korean Journal of Optics and Photonics
• /
• v.13 no.5
• /
• pp.373-376
• /
• 2002

An asymmetrical directional coupler with two nonidentical fibers has, for the first time, been proposed and analyzed for an EDFA gain flattening filter (GFF). The characteristics of the transmission spectra of the GFFs have been theoretically investigated for the core spacings, the coupling lengths and the fiber parameters of the asymmetrical directional coupler. The analytical results show that an EDFA gain spectrum with flatness of ~7 ㏈ can be flattened to within $\pm$0.75 ㏈ over a bandwidth of 30 nm by using the asymmetrical directional coupler-based GFF.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.675-681
• /
• 2016

A 41dB gain control range $6^{th}$-order band-pass receiver front-end (RFE) using CMOS switched frequency translated impedance (FTI) is presented in a 40 nm CMOS technology. The RFE consists of a frequency tunable RF band-pass filter (BPF), IQ gm cells, and IQ TIAs. The RF BPF has wide gain control range preserving constant filter Q and pass band flatness due to proposed pre-distortion scheme. Also, the RF filter using CMOS switches in FTI blocks shows low clock leakage to signal nodes, and results in low common mode noise and stable operation. The baseband IQ signals are generated by combining baseband Gm cells which receives 8-phase signal outputs down-converted at last stage of FTIs in the RF BPF. The measured results of the RFE show 36.4 dB gain and 6.3 dB NF at maximum gain mode. The pass-band IIP3 and out-band IIP3@20 MHz offset are -10 dBm and +12.6 dBm at maximum gain mode, and +14 dBm and +20.5 dBm at minimum gain mode, respectively. With a 1.2 V power supply, the current consumption of the overall RFE is 40 mA at 500 MHz carrier frequency.