• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.1
• /
• pp.63-68
• /
• 2004

Recently ER fluids are put to practical use in fluid power industry field. As only with electrical signal change to the valve in which ER fluid flowing, ER fluid flow is controlled, so devepment of simple ER valves have been tried. In this case a technical problem is to check the pressure drop caused from flow rate change in valves because the pressure drop is very small. In this study ER valves are designed and manufactured, and small pressure drop induced from flow rate change is checked by pressure transducer which is made with appling strain gage. The ER valves and pressure drop check method are considered to be applied to the fluid power industry.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.66-72
• /
• 2000

Commercial eddy current dynamometers control the torque of ratating body (poer supply machine) with the field coil current being operated as a braking force. In this paper, we studied about the relation between the field coil current and the torque load of eddy current dynamometer. By the torque measuring analysis of eddy current dynamometer, it is linear relation between the brake force measured from the torque meter (e.g. load cell, strain gage or spring balance etc.) which is installed at the case of dynamometer and the multiply of shaft rpm by the square of field coil current (N$\times$Ia2). To prove the relation, it was experimented and showed that the torque operated by the rotating body can be measured with the shaft rpm and the field coil current of eddy current dynamometer. This result shows a possibility that eddy current dynamometer can measures the torque of rotating body without special torque measuring devices.

• 연구논문집
• /
• s.26
• /
• pp.33-42
• /
• 1996

The transmission system of a washing machine which is called by the clutch is one of the most important components to preserve the performance. The clutch housing has a role to guard and mount the transmission system on the frame of the machine. The load which is applied on the clutch housing depends on the operating conditions. Nowadays the dehydration speed is higher and higher in order to improve the efficiency. In this study, the strains on the predicted weak positions were measured using the strain gage and its measuring equipment. The relationships between the dehydration speeds and the maximum principal strains were obtained. Finite element analysis is executed to acquire the effect of the dehydration speed on the stress of the clutch housing. The distributions of the equivalent stress and the maximum stresses under the various speeds, the various loading directions and the various thickness of the clutch housing were obtained.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.698-703
• /
• 2001

This paper is concerned with the nonlinear hyperelastic problem fur the incompressible characteristics of the rubber. Tension sensor is a strain gage type load cell element for a fence intrusion detection system and consists of the sensing part and the rubber housing. The analysis includes an elastic analysis and a hyperelastic analysis of a tension sensor for the deformed shape and variation of the maximum strain on the sensing part with respect to the vertical load. Numerical results show that the hyperelastic model is stiffer and less deformed than the elastic model. Comparing with the experimental test data, we know the hyperelastic model is the better approximation than the elastic model.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.82-87
• /
• 2011

본 연구에서는 충북 괴산 달천의 수전교 지점에서 기포식, 압력식, 레이더, 부자식 등 4종의 수위계를 함께 운영하여 얻은 자료를 바탕으로 관측 기종과 조건에 따른 수위값의 특성을 상대 비교 분석하였다. 기준 수위는 동시간대 측정한 4개 수위계의 평균값을 이용하였다. 분석 결과 전체적으로 수위계가 약 ${\pm}2%$ 범위에서 상대차이가 발생하고 있으나 레이더 수위계는 저수위에서는 이보다 약간 큰 범위에서 변동하고 있고, 홍수시에도 일부 측정 결과들은 큰 변동성을 보이고 있음을 알 수 있었다. 이 결과는 각 수위계의 오차 특성을 정확하게 판단할 수는 없고 경향성만 보여주었으나 측정 환경과 기종에 따른 차이가 다소 있음을 보여주었다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.158-159
• /
• 2017

In this study, it evaluate the strain properties of fiber reinforced concrete and fiber reinforced cement composite. The types of fiber are Hooked steel fiber and it was mixed 0.5, 1.0 vol.% in concrete and 1.0, 2.0 vol.% in cement composites. The impact test was conducted by using a projectile (diameter: 25mm, velocity: 170m/s) and strain properties on the rear side of each specimen was evaluated by strain gage. After the impact test, fracture grade, fracture depth was evaluated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.577-580
• /
• 2003

The magnetostriction of FeCoGe/phenol composites, which is one of the magnetostrictive materials, measured at the external magnetic field. The measurement was carried out using the electrical-resistance strain gage, the wheaten's Bridge for eliminating the unnecessary voltage, and the lock-in-amp for signal amplification and noise filtering. When the external magnetic field was applied in the longitudinal the samples, the maximum strain of 120ppm was taken with regard to the 10wt.% phenol composite. This results indicate that the FeCoGe/phenol composites can be useful as an actuator because it has larger stain than the other solid state actuators such as piezo electric materials.

• Journal of Welding and Joining
• /
• v.17 no.5
• /
• pp.83-88
• /
• 1999

In this paper resistance projection weldability of Zn coated steels with post treatment has been discussed. Projection welding was performed by a condenser discharge type power source which was equipped with welding parameter monitoring system. Mechanical test results indicated that the effect of post coatings on the projection front changed showing very small very small spattering at the weld strength was negligible. However, contamination rate of the block electrode varied depending on the post treatment coatings. Test results also showed that projection height before welding should be kept to be 80-100% of the specimen thickness as far as the surface quality was taken into consideration. Based on the high speed photography, discharge condition at the beginning stage of the welding process. It was considered that the spattering reduced the weld strength slightly at the optimum heat input range.

• Journal of Welding and Joining
• /
• v.19 no.3
• /
• pp.317-324
• /
• 2001

This study deals with high power Nd:YAG laser welding of thin steels for small pressure vessels. Full penetration welding at the overlap joint was performed so as to assure sufficient weld strength. Results showed that mid-depth weld size reduced drastically with increasing the travel speed. Position of focus had little effect on the bead formation even though short focal system was used. However, the shape factor and the bead width had closely related with the position of focus. Based on the microstructural inspection, acceptable weld was obtained when the overlap clearance was controlled up to 20% of the base metal thickness. In the case that the joint contained more clearance than the critical value, both the tensile shear strength and the tear strength were reduced. Results also demonstrated that shielding gases were proved to play a key role as far as the bead formation characteristics was taken into consideration. Blowing dry air through 5mm in diameter nozzle produced narrower bead cross-section than that of argon or nitrogen shielding.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.3
• /
• pp.37-42
• /
• 1998

The important parts of the developing AGV model are the fabrication of each part and the design technology of body frame. In the present day, design of the body frame depends on the experience of the industrial place. the systematic data need for the optimal design of the frame for the case of model change. In this study, the strength of the early stage AGV(Automatic guided vehicle) is examined with the 3-dimensional finite elemnt method. In order to verify the finite element results, the computed results are compared with the experimental data from the strain-gage output. A New model was designed by rmoving some parts of the early staged(roughyly designed) model and choosing the thickness change of the rectangular-pipes.