• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.3
• /
• pp.252-257
• /
• 2000

To investigate the thermal preheating effect of the GaAs substrate exerted on the ZnS epilayers for the first time, ZnS epilayers were grown on the GaAs (100) substrate by hot wall epitaxy. The thermal preheating temperature was $450^{\circ}C$~$660^{\circ}C$. The full width at half maximum values of double crystal rocking curve were the smallest for the ZnS epilayers grown on the GaAs thermally preheated at around both $500^{\circ}C$ and $600^{\circ}C$. However, photoluminescence characteristics of ZnS epilayers were better at $600^{\circ}C$ than at $500^{\circ}C$. Therefore, it was shown that the optimum preheating temperature of the GaAs substrate for the growth of high quality ZnS epilayer was around $600^{\circ}C$. From these experimental results, it was shown that the crystal quality and the PL properties of ZnS epilayers were enhanced for the GaAs substrates thermally preheated at $600^{\circ}C$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.11
• /
• pp.29-34
• /
• 2004

This paper reports the RF dispersion and linearity characteristics of unpassivated AlGaN/InGaN/GaN high electron-mobility transistors (HEMTs) grown by molecular beam epitaxy (MBE). The devices with a 0.5 ${\mu}{\textrm}{m}$ gate-length exhibited relatively good DC characteristics with a maximum drain current of 730 mA/mm and a peak g$_{m}$ of 156 mS/mm. Highly linear characteristic was observed by relatively flat DC transconductance (g$_{m}$) and good inter-modulation distortion characteristics, which indicates tight channel carrier confinement of the InGaN channel. Little current collapse in pulse I-V and load-pull measurements was observed at elevated temperatures and a relatively high power density of 1.8 W/mm was obtained at 2 GHz. These results indicate that current collapse related with surface states will not be a power limiting factor for the AlGaN/InGaN HEMTs.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.150-150
• /
• 2003

wide bind gap과 wurtzite hexagonal structure를 가지고 있으며 청색 발광 및 청자색 레이저 특성을 보이는 III-V족 화합물반도체 GaN는 laser diodes (LD) 및 light emitting diodes (LED) 재료로 주목받고있는 주요 전자재료이다. 본 연구에서는 GaN를 chemical vapor deposition (CVD) 법을 이용하여 vapor-liquid-solid (VLS) mechanisum에 의하여 GaN나노와이어 형태로 성장시켰다. 기판은 (001)Si을 사용하였고 suputtering을 이용하여 GaN와 AlN의 double buffer layer (DBL)를 증착시켰으며 촉매로는 Ni을 사용하였다. 또한, 원료로는 고순도 Ga금속과 NH$_3$ gas를, carrier gas로는 Ar을 사용하여 GaN/AlN/(001)Si 위에 GaN 나노와이어를 성장시켰다. 성장된 GaN 나노와이어는 DBL의 두께, Ga source의 양, 튜브 안의 압력, 튜브 안의 위치 등의 제 공정변수에 따라 tangled, straight 등의 다양한 형상을 보였으며 지름은 약 30~100 nm, 길이는 수 $\mu\textrm{m}$로 관찰되었다. GaN나노와이어의 결정성, 형상 및 발광특성 등을 x-ray diffraction (XRD), photoluminesence (PL), scanning electron microscope (SEM), transmision electron microscope (TEM) 등을 이용하여 측정하였으며 제 공정변수와의 상관관계를 규명하였다.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.4
• /
• pp.33-37
• /
• 1992

AlGaAs/GaAs quantum well delta-doped channel FET's have been successfully fabricated using by low-pressure metalorganic chemical vapor deposition(LP-MOCVD). The FET's with a gate dimension of 1.8$\mu$m $\times$ 100$\mu$m have a maximum transconductance of 190 mS/mm and a maximum current density of 425 mA/nm. The devices show extremely broad transconductances with a large voltage swing of 2.4V. The S-parameter measurements have indicated that the current gain and power gain cutoff frequencies of the device were 7 and 15 GHz, respectively. These values are among the best performance reported for GaAs based heterojunction FET's with a similar device geometry.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.12
• /
• pp.11-17
• /
• 2000

We investigated the growth of InGaN/GaN multiple quantum wells (MQWs) structures which emit blue light. The samples were grown in a low pressure metalorganic chemical vapor deposition system. We examined InGaN/GaN MQWs by varying growth temperatures and thicknesses of InGaN well and GaN barrier layers in MQWs. Especially, the thickness of GaN barrier in InGaN/GaN MQWs was found to severely affect the interfacial abruptness between InGaN well and GaN barrier layers. The higher order satellite peaks in the high resolution x-ray diffraction spectra and the high resolution cross sectional transmission electron microscope image of MQW structrues revealed that the interface between InGaN and GaN layers was very abrupt. Room-temperature photoluminescence spectra also showed a blue emission from InGaN/GaN MQWs at the wavelength of 463.5nm with a narrow full width at half maximum of 72.6meV.

• Journal of Korean Vacuum Science & Technology
• /
• v.4 no.3
• /
• pp.81-85
• /
• 2000

The effects of $NH_3$ flow rate and reactor pressure on Al composition and the interface of AlGaN/GaN heterostructure were studied. Equilibrium partial pressure of Ga and Al over AiGaN alloy was calculated as a function of growth pressure, $NH_3$flow rate and temperature. It was found equilbrium vapor pressure of Al is significantly lower than that of Ga, thus, the alloy composition mainly controlled by Ga partial pressure. We believe that more decomposition of Ga occur at lower $NH_3$ flow rate and higher growth pressure leads to preferred Al incorporation into AlGaN. The alloy composition gradient became larger at AlGaN/GaN heterointerface at higher reactor pressures, higher Al composition and low $NH_3$ flow rate. This composition gradient lowered sheet carrier concentration and electron mobility as well. We obtained an AlGaN/GaN heterostructure with sheet carrier density of ${\sim}2{\times}10^{13}cm^{-2}$ and mobility of 1250 and 5000 $cm^2$/Vs at 300 K and 100 K, respectively.

• Journal of the Korean Vacuum Society
• /
• v.7 no.s1
• /
• pp.15-19
• /
• 1998

Structural and optical properties of $In_xGa_{1-X}N$ as well as $In_{0.1}Ga_{0.9}N$/GaN single quantum we11 (SQW) grown on sapphire (0001) substrate with an based GaN using rf-plasma assisted MBE have been investigated. The quality of the InXGal.,N fdm was improved as the growth temperature increased. In PL measurements at low temperatures, the band edge emission peaks of $In_xGa_{1-X}N$ was shifted to red region as an indium cell and substrate temperature increased. For $In_{0.1}Ga_{0.9}N$/GaN SQW, the optical emission energy has blue shift about 15meV in PL peak, due to the confined energy level in the well region. And, the FWHM of the $In_{0.1}Ga_{0.9}N$/GaN SQW was larger than that of the bulk Ino,la.9N films. The broadening of FWHM can be explained either as non-uniformity of Indium composition or the potential fluctuation in the well region. Photoconductivity (PC) decay measurement reveals that the optical transition lifetimes of the SQW measured gradually increased with temperatures.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.72-75
• /
• 2012

In our experiments, strain-free nanowires(NWs) were dispersed on to the substrate, followed by e-beam lithography(EBL) to fabricate single nanowire ultraviolet(UV) sensor devices. Focused-ion beam(FIB), micro-Raman spectroscopy and photoluminescence were employed to characterize the structural and optical properties of AlGaN/GaN NWs. Also, I-V characteristics were obtained under both dark condition and UV lamp to demonstrate AlGaN/GaN NW-based UV sensors. The conductance of a single AlGaN/GaN UV sensor was 9.0 ${\mu}S$(under dark condition) and 9.5 ${\mu}S$ (under UV lamp), respectively. The currents were enhanced by excess carriers under UV lamp. Fast saturation and decay time were demonstrated by the cycled processes between UV lamp and dark condition. Therefore, we believe that AlGaN/GaN NWs have a great potential for UV sensor applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.249-249
• /
• 1999

GaN과 같은 III-nitride 반도체 관한 식각 기술의 연구는 blue-emitting laser diode(LD)를 위한 경면(mirror facet)의 형성뿐만아니라 새로운 display 용도의 light emitting diodes (LED), 고온에서 작동되는 광전소자 제조 등에도 그 중요성이 증대되고 있다. 최근에는 III-nitride 물질의 높은 식각속도와 미려하고 수직한 식각형상을 이루기 위하여 ECR(Electron Cyclotron Resonance)이나 ICP(Inductively Coupled Plasma)와 같은 고밀도 플라즈마 식각과 CAIBE(Chemically assisted ion beam etching)를 이용한 연구가 진행되고 있다. 현재 제조되어 지고 있는 LED 및 LD와 같은 광소자의 구조의 대부분은 p-GaN/AlGaN/InGaN(Q.W)/AlGaN/n-GaN 와 같은 여러 층의 형태로 이루어져 있다. 이중 InGaN는 광소자나 전자소자의 특성에 영향을 주는 가장 중요한 부분으로써 현재까지 보고된 식각연구는 undoped GaN에 대부분 집중되고 있고 이에 비해 소자 특성에 핵심을 이루는 InGaN의 식각특성에 관한 연구는 미흡한 상황이다. 본 연구에서는 고밀도 플라즈마원인 ICP 장비를 이용하여 InGaN를 식각하였고, 식각에는 Cl2/CH4, Cl2/Ar 플라즈마를 사용하였다. InGaN의 식각특성에 영향을 미치는 플라즈마의 특성을 관찰하기 위하여 quadrupole mass spectrometry(QMS)와 optical emission spectroscopy(PES)를 사용하였다. 기판 온도는 5$0^{\circ}C$, 공정 압력은 5,Torr에서 30mTorr로 변화시켰고 inductive power는 200~800watt, bias voltage는 0~-200voltage로 변화시켰으며 식각마스크로는 SiO2를 patterning 하여 사용하였다. n-GaN, p-GaN 층 이외에 광소자 제조시 필수적인 InGaN 층을 100% Cl2로 식각한 경우에 InGaN의 식각속도가 GaN에 비해 매우 낮은 식각속도를 보였다. Cl2 gas에 소량의 CH4나 Ar gas를 첨가하는 경우와 공정압력을 감소시키는 경우 식각속도는 증가하였고, Cl2/10%Ar 플라즈마에서 공정 압력을 감소시키는 경우 식각속도는 증가하였고, Cl2/10%CHF3 와 Cl2/10%Ar 플라즈마에서 공정압력을 15mTorr로 감소시키는 경우 InGaN과 GaNrks의 선택적인 식각이 가능하였다. InGaN의 식각속도는 Cl2/Ar 플라즈마의 이온에 의한 Cl2/CHF3(CH4) 플라즈마에서의 CHx radical 형성에 의하여 증가하는 것으로 사료되어 진다.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.10a
• /
• pp.149-154
• /
• 1997

광소자 및 새로운 개념의 전력소자 응용을 위하여 Wide Bandgap 반도체에 대한 관심이 급증되고 있다. 특히 직접천이형인 GaN는 청색 발광소자 응용 및 고출력, 고주파용 전력소자 응용에 이상적인 전자물성을 갖고 있다. 따라서 본 연구에서는 GaCl$_3$와 NH$_3$를 source gas로 하는 CVPE법을 사용하여 (0001) sapphire와 비교하였다. 기판의 증착온도 104$0^{\circ}C$에서 source gas의 III/V flow rate를 2로 분석하여 45분간 성장시킨 경우 그 증착속도는 약 40 $\mu\textrm{m}$/hr 정도였으며, 이 때 XRD을 향상시키기 위하여 증착이전에 기판의 표면에 증착온도에서 NH$_3$를 이용한 nitridation 처리를 하였으며, 그 처리시간이 3분일 때 XRD의 FWHM 특성이 가하여 조사한 결과 363 nm에서 peak가 검출되었다. 본 연구에서는 양질의 GaN 박막성장을 위한 증착조건 인자중 source gas의 flow rate가 가장 중요한 변수임을 적정 온도 범위가 75$0^{\circ}C$ 근처로 조사되었다. 실험과 모사결과의 박막 증착 최적온도의 차이는 GaN 증착시의 반응 Kinetics가 느리기 때문인 것으로 해석된다.