• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.69-70
• /
• 2010

본 논문에서는 전기자동차의 동력용 모터로 적합한 고효율 고출력 특성의 IPMSM을 적용하여 고 정밀 위치센서에 의한 벡터제어 알고리즘 및 인버터 제어기를 개발하였다. 개발된 제어기의 알고리즘 검증을 위해 PSIM을 이용하여 시뮬레이션을 수행하였고, 다이나모 부하시험을 통하여 제어기의 안정된 운전특성을 가짐을 확인하였다.

• Transactions of Materials Processing
• /
• v.18 no.6
• /
• pp.482-487
• /
• 2009

A finite element based microstructural modeling for the size dependent strengthening of particle reinforced aluminum composites is presented. The model accounts explicitly for the enhanced strength in a discretely defined "punched zone" around the particle in an aluminum matrix composite as a result of geometrically necessary dislocations developed through a CTE mismatch. The density of geometrically necessary dislocations is calculated considering volume fraction of the particle. Results show that predicted flow stresses with different particle size are in good agreement with experiments. It is also shown that 0.2% offset yield stresses increases with smaller particles and larger volume fractions and this length-scale effect on the enhanced strength can be observed by explicitly including GND region around the particle. The strengths predicted with the inclusion of volume fraction in the density equation are slightly lower than those without.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.322-325
• /
• 2009

An enhanced continuum model for the size dependent strengthening of particle reinforced composites is presented. The model accounts explicitly for the enhanced strength in a discretely defined "punched zone" around the particle in a metal matrix composite as a result of geometrically necessary dislocations developed through a CTE mismatch. The size of the punched zone presents an intrinsic length scale, and this results in the size dependence of the overall behavior of the composite. Results show that predicted 0.2% offset yield stresses are increasing with smaller inclusions and larger volume fractions and this length-scale effect on the enhanced strength can be observed by explicitly including GND region around the particle.

• Journal of the Microelectronics and Packaging Society
• /
• v.4 no.2
• /
• pp.25-32
• /
• 1997

대용량, 고속 정보처리가 요구되는 System의 모듈은 Data 처리의 고속성 및 회로의 고집적이 가능한 MCM의 형태로 구현되어 ATM, GPS 및 PCS 등의 분야에 광범위하게 응 용되고 있다. 위와 같은 High Speed 응용분야에서의 System 성능은 Interconnect Line의 전달지연, 임피던스 부정합에 의한 신호 반사 손실. 신호선 간의 Crosstalk, Ground Bounce 등의 현상에 대한 최적화 여부에 결정적인 영향을 받는다. 그러나 Interconnect의 특성상 정 형이 존재하지 않으므로 추상적인 Library를 구축하는 형식으로 접근할 수밖에 없으며 이를 위하여 여러기본 구조를 정의한후 각 Dimension을 변수로 두고 해석 결과를 합성하여 Database화하는 접근방식이다. 본 논문에서는 MCM-D 공정을 이용하여 Interconnect Line 특성을 분석하고 Database화 하기 위한 Test Pattern을 구현하고 Time Domain reflectometry(TDR)을 이용하여 그특성들을 측정 분석하였다. Test pattern 제작은 MCM-D 공정으로 최소선폭 27$\mu$m, Via Hole 75$\mu$m으로 형성하였고 2 Layer Signal과 GND로 총 3Layer를 구현하였다. 특성분석을 위해 TDR장비와 모데링 및 Simulation S/W인 IPA 510 을 사용하였다. 이를 통해 MCM-D를 이용한 공정에서 Interconcet Line의 고주파 특성을 측정하고 정량화하여 LIbrary를 제작할수 있었다.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.28-29
• /
• 2013

DC-DC Buck Converter는 입력 전압보다 출력전압이 낮은 컨버터이며 강압형 컨버터라고도 한다. 입력과 출력이 같은 접지를 공유하는 회로에 쓰이며, 스위칭 소자를 이용하여 듀티비에 따라 출력전압을 제어할 수 있고, 출력단의 LC 필터를 통해 평활(평균)하여 직류전압을 얻을 수 있다. DC-DC Buck Converter는 제어가 간단하고 설계가 쉬워 주로 회로의 파워부에 많이 쓰이고 있으며, 본 논문에서는 DC-DC Buck Converter의 기본형과 2Stage DC-DC Buck Converter 그리고 기본형의 GND단에 L을 추가한 DC-DC Buck Converter의 응답특성을 비교 및 분석을 함으로써 이론적 해석과 시뮬레이션을 통한 특성을 비교 하고자 한다.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2473-2475
• /
• 1998

In this paper, we implemented RS232C serial communication by the 2 wires(Data,GND), and multiple access, by the applying Collision Sensing Multiple Access(CSMA) Protocol. Multiple access is implemented by assigning a unique ID to each controller. The multiple access control operation starts by sending a command packet from a host to another host and the command packet is composed of ID bytes of source and target host computer, data bytes and the check sum, byte. In host computer, after sending command packet, the collision from loop back data. If collision is detected, it means a command packet was collided with another command packet for another host. The packet communication of the controller enables the multiple acces of the controller through the common serial data link. The application of this serial communication through CSMA protocol and the usage of two wires, have an effect on saving the wires and convenient of layout work.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.6
• /
• pp.51-57
• /
• 1997

Low-voltage, low-power gm-C filter utilizing newly dveloped operational transconductance amplifier (OTA) is described in this paper. The OTA has only two MOS transistors in saturation region between $V_{DD}$ and GND, and thus low voltage operation is possible. To improve the linearity, the OTA is made differential. Common mode feedback, essential in differential circuit, requires no additional implemented in $0.8\mu\textrm{m}$ CMOS process, and the center frequency can be controlled from 15MHz with 3.0V single power supply.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.9
• /
• pp.546-551
• /
• 2000

A micromechanical switch that can be used as a logic gate is described in this paper. This switch consists of fixed input electrodes an output electrode Vcc/GND electrodes and movable plates suspended by crab-leg flexures. for mechanical switching of an electrical signal a parallel plate actuator which comes in contact with output electrode was used. Provided that movable plates are connected to Vcc and a low input voltage(ground signal) is applied to the fixed input electrodes the movable plates are pulled by an electrostatic force between the fixed input electrodes and the movable plates. the proposed micromechanical switch was fabricated by surface micromachining technology with$2\mum$ -thick poly-Si and the measured threshold voltage for ON/OFF switching was 23.5V.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.4
• /
• pp.338-347
• /
• 2021

In this paper, the beta-ray sensor circuit used in the true random number generator was designed using DB HiTek's 0.18㎛ CMOS process. The CSA circuit proposed a circuit having a function of selecting a PMOS feedback resistor and an NMOS feedback resistor, and a function of selecting a feedback capacitor of 50fF and 100fF. And for the pulse shaper circuit, a CR-RC2 pulse shaper circuit using a non-inverting amplifier was used. Since the OPAMP circuit used in this paper uses single power instead of dual power, we proposed a circuit in which the resistor of the CR circuit and one node of the capacitor of the RC circuit are connected to VCOM instead of GND. And since the output signal of the pulse shaper does not increase monotonically, even if the output signal of the comparator circuit generates multiple consecutive pulses, the monostable multivibrator circuit is used to prevent signal distortion. In addition, the CSA input terminal, VIN, and the beta-ray sensor output terminal are placed on the top and bottom of the silicon chip to reduce capacitive coupling noise between PCB traces.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.9
• /
• pp.471-475
• /
• 2001

ln this paper, a micromachined micromechanical switch is presented. The presented switch is operated in the vertical direction to the substrate by an electrostatic force between two parallel plates. The moving plate is pulled down to connect the bumps of the bias node$(V_{DD}/ or GND)$ to the bumps of the output node when a oltage difference exists between the moving plate and the input plate. The switch was designed to operate at a low switching voltage$(\risingdotseq5V)$ by including a large-area, narrow-gap, parallel plate capacitor A theoretical analysis of the designed switch was performed in order to determine its geometry fitting the desired pull-in voltage and release voltage. The designed switch was fabricated by surface micromachining combined with Ni electroplating. From the experimental results of the fabricated switch, its pull-in voltage came Out to be less than 5V and the measured maximum allowable current was 150mA. The measured average ON-state resistance was about 8$\Omega$, and the OFF-state resistance was too high to be measured with digital multimeter.