• Tribology and Lubricants
• /
• 제29권1호
• /
• pp.13-18
• /
• 2013

Slider bearing is a widely used load-carrying element in the industry. While a large number of studies have investigated the effect of overall surface curvature, very few have considered sinusoidal surface. Recently, consideration of surface roughness/waviness or intentional wave design has been identified as an important issue in the manufacture of hard disk driver, mechanical seal, hydraulic machine, and etc. This study investigated the load-carrying capacity of a finite-width slider bearing with a wavy surface. Film thickness ratios, length-width ratio, ambient pressure, amplitude, and partial distribution were selected as the simulation parameters. The calculation results showed that the load-carrying capacity rapidly varied at small film thickness ratio, but the waviness near the area of minimum film thickness made much more influence with an increase in film thickness ratio. As the length-width ratio of bearing was increased, ambient pressure became more influential at small film thickness ratios. Furthermore a particular partial distribution of the wavy area led to higher load-carrying capacity than did the whole distribution. Consequently, the results of this study are expected to be of use in surface micro-machining of finite-width slider bearings.

• International Journal of Vascular Biomedical Engineering
• /
• 제4권2호
• /
• pp.25-30
• /
• 2006

We intended to measure the IT, MT, and the IMT of carotid artery separately and tried to analyze the clinical significance. Two hundred and fifty consecutive patients (125 males, 125 females) underwent carotid artery scanning using high-resolution ultrasound. The images were off-line analyzed using B-mode ultrasound image processing, devised in our research. We measured the IT, MT, and IMT semi-automatically at the far wall of designated 1cm length of the right common carotid and calculated the average values over the 200 points. The IT (p < 0.05), MT (p < 0.05) as well as IMT (p < 0.01) of patients with atherosclerotic disease were significantly thicker than that of the patients without atherosclerotic disease. Patients with hypertension showed significantly thicker IT (p < 0.05), MT (p < 0.01), and IMT (p < 0.01) than that of the patients without hypertension. However, only IT was thicker in patients with smoking (p < 0.05) than that of the patients without smoking. Smoking was associated only with intima while hypertension was associated with the all three layer's thickness. This result suggests the atherosclerotic process can be different by cardiovascular risk factors.

• Journal of the Korean Society of Fashion and Beauty
• /
• 제5권2호
• /
• pp.48-55
• /
• 2007

This Study was conducted in order to provide a satisfying beauty service to customers by investigating the effect of hair thickness on personality and attitude of hair style. It executed a survey of customers within the age of $20{\sim}}40$ who come and go to beauty salons, dwell in Kyeong-gi and Seoul. First, it investigated the difference of blood types depending on hair thickness. Second, it investigated how hair thickness affects on types of personality. Third, it investigated the difference of hair style attitude depending on hair thickness. We picked normal hairs for mineral test from our salon customers of the occipital region, except coloring hairs, white hairs. The hairs were picked 2 cm off from the scalp. In the result, many people with thick hair were found to have the blood type O, and many people with thin hair were found to have the blood type A. Also, in the types of personality the owners of thick hair and thin hair were highly found to have characters of both sexes, the owners of normal hair were highly found to have feminine characters. Many of the owners of thick hair appeared to prefer short hair styles, a high percentage of the owners with thin hair appeared to have long hair styles, A type people who are introspective prefer soft and long hair styles which have less movement.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.239-246
• /
• 2010

When galvanized steel strip is produced through a continuous hot-dip galvanizing process, the thickness of the adhered zinc film is controlled by impinging a thin plane nitrogen gas jet. The thickness of the zinc film is generally affected by impinging pressure distribution, its gradient and shearing stress at the steel strip. These factors are influenced by static pressure of gas spraying at air knife nozzle, a nozzle-to-strip distance and strip and a geometric shape of the air knife, as well. At industries, galvanized steel strip is produced by changing static pressure of gas and a distance between the air knife nozzle and strip based on experimental values but remaining a geometric shape of nozzle. Splashing and check-mark strain can generally occur when a distance between the air knife nozzle and strip is too short, while ability of zinc removal can lower due to pressure loss of impinging jet when a distance between the air knife nozzle and strip is too long. In present study, buckling of the jet and change of static pressure are observed by analyzing flow characteristics of the impinging jet. The distance from the nozzle exit to the strip varies from 6 mm to 16 mm by an increment of 2 mm. Moreover, final coating thickness with change of a distance between the air knife nozzle and strip is compared with each case. An ability of zinc removal with the various distances is predicted by numerically calculating the final coating thickness.

• Journal of Technologic Dentistry
• /
• 제43권3호
• /
• pp.77-83
• /
• 2021

Purpose: The purpose of this in vitro study was to measure and compare the thickness-dependent color dimensions of digital light processing (DLP) three-dimensional (3D) printer and conventional interim restorative resin. Methods: Specimens (N=60) were fabricated using either subtractive manufacturing (S group) or DLP 3D printing (D group) material. All milled and 3D-printed specimens were allocated into three different groups (n=10) according to different thicknesses as follows: 1.0, 1.5, and 2.0 mm. Color measurements in the CIELab coordinates were made using a spectrophotometer under room light conditions (1,003 lux). The color differences (𝚫E^*) between the specimen and control target data were calculated. Data were analyzed using the oneway analysis of variance (ANOVA). Post hoc comparisons were conducted using Tukey's honestly significant difference method (α=0.05 for all tests). Results: The 𝚫L^*, 𝚫a^*, 𝚫b^*, and 𝚫E^* values of interim restorative resin produced by DLP 3D printing were obtained in terms of the specimen's thickness increased compared with the increases by subtractive manufacturing. When the thickness was similar, the color difference between subtractive manufacturing and DLP 3D printing was ≥5.5, which is a value required by the dentist for remanufacturing. Conclusion: Color was influenced by the thickness of the interim restorative resin produced by DLP 3D printing.

• Physical Therapy Korea
• /
• 제28권3호
• /
• pp.186-193
• /
• 2021

Background: While the formal test has been used to provide a quantitative measurement of core stability, studies have reported inconsistent results regarding its test-retest and intraobserver reliabilities. Furthermore, the validity of the formal test has never been established. Objects: This study aimed to establish the concurrent validity and test-retest reliability of the formal test. Methods: Twenty-two young adults with and without core instability (23.1 ± 2.0 years) were recruited. Concurrent validity was determined by comparing the muscle thickness changes of the external oblique, internal oblique, and transverse abdominal muscle to changes in core stability pressure during the formal test using ultrasound (US) imaging and pressure biofeedback, respectively. For the test-retest reliability, muscle thickness and pressure changes were repeatedly measured approximately 24 hours apart. Electromyography (EMG) was used to monitor trunk muscle activity during the formal test. Results: The Pearson's correlation analysis showed an excellent correlation between transverse abdominal thickness and pressure biofeedback unit (PBU) pressure as well as internal oblique thickness and PBU pressure, ranging from r = 0.856-0.980, p < 0.05. The test-retest reliability was good, intraclass correlation coefficient (ICC1,2) = 0.876 for the core stability pressure measure and ICC1,2 = 0.939 to 0.989 for the abdominal muscle thickness measure. Conclusion: Our results provide clinical evidence that the formal test is valid and reliable, when concurrently incorporated into EMG and US measurements.

• Journal of Korean Physical Therapy Science
• /
• 제30권3호
• /
• pp.72-83
• /
• 2023

Background: Normal-weight obese women have a normal weight with relatively low muscle mass resulting from high body fat. We aimed to investigate the effects of core exercise on body composition, abdominal muscle thickness, trunk muscular endurance, and psychological factors in normal-weight obese women. Design: One group pre-, mid-, and post-test design. Methods: A total of 20 normal-weight obese women were recruited voluntarily. Core exercises were performed for 30 minutes, three times a week for 4 weeks. InBody measurements, ultrasound imaging, and clinical tests were used to assess body composition, abdominal muscle thickness, trunk and core muscular endurance, and psychological condition(satisfaction with appearance and self-esteem). The dependent variables were measured three times: before the intervention (pre-test), 2 weeks after the intervention (mid-test), and 4 weeks after intervention (post-test). One-way repeated measures ANOVA and Friedman test were used for statistical analysis. Results: Although there was no change in the body composition (p>0.05), thickness of the transversus abdominis and internal and external oblique muscles, endurance of the trunk flexors and extensors and core muscles, and psychological condition showed significant differences after the intervention (p<0.05). Conclusion: Our findings will help develop exercise programs for normal-weight obese individuals that utilize the beneficial effect of core exercises.

• Corrosion Science and Technology
• /
• 제20권1호
• /
• pp.7-14
• /
• 2021

PosMAC^® is a brand of Zn-Mg-Al hot-dip coated steel sheet developed by POSCO. PosMAC^® can form dense surface oxides in corrosive environments, providing advanced corrosion resistance compared to traditional Zn coatings such as GI and GA. PosMAC^® 3.0 is available for construction and solar energy systems in severe outdoor environments. PosMAC^®1.5 has better surface quality. It is suitable for automotive and home appliances. Compared to GI and GA, PosMAC^® shows significantly less weight reduction due to corrosion, even with a lower coating thickness. Thin coating of PosMAC^® provides advanced quality and productivity in arc welding applications due to its less generation of Zn fume and spatters. In repeated friction tests, PosMAC^® showed lower surface friction coefficient than conventional coatings such as GA, GI, and lubricant film coated GA. Industrial demand for PosMAC^® steel is expected to increase in the near future due to benefits of anti-corrosion and robust application performance of PosMAC^® steel.

• Proceedings of the Korean Magnestics Society Conference
• /
• 한국자기학회 2007년도 The 1st International Symposium on Advanced Magnetic Materials
• /
• pp.155.1-155.1
• /
• 2007

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.197-197
• /
• 2009

We have investigated the holographic grating formation on Ag-doped amorphous chalcogenide AsGeSeS thin films with Ag thickness. Holographic gratings have been formed using Diode Pumped Solid State laser (DPSS, 532.0nm) under [P:P] polarized the intensity polarization holography. The diffraction efficiency was obtained by +1st order intensity.