• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.497-502
• /
• 2008

In this paper, we studied on an attenuation effect of automobile exhaust noise according to the direction of secondary sound source in duct ANC system. Automobile exhaust noise was recorded at 800rpm. 3500rpm and 5000rpm of a diesel engine. Directions of loudspeaker(second sound source) can be exchanged to $30^{\circ}$, $90^{\circ}$ and $150^{\circ}$ against the primary noise flow by acrylic ducts to be made for experimentation. DSP board with TMS320C6416 chip of Texas Instrument Co used to control adaptive ANC system. This ANC system is based on the single-channel FxLMS algorithm. In experiment result, when the loud speaker direction was $150^{\circ}$, the attenuation effect showed largely. In case of $90^{\circ}$ duct, the noise was a little increased. In case of $30^{\circ}$ duct, the noise was a little increased or decreased according to the frequency range and the sound pressure(dB) of exhaust noise to comply with engine rpm.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.9
• /
• pp.628-636
• /
• 2015

In this study, theoretical and experimental analyses were performed for creating and moving the zone of quiet(ZoQ) to the ear location of a sitter by using active sound control technique. As the ZoQ is actively created at the location of the error microphone basically with an active sound control system using an algorithm such as the filtered-x least mean square(FxLMS), the virtual microphone control(VMC) method was considered to move the location of the ZoQ to around the sitter`s ear. A chair system with microphones and loudspeakers on both sides was manufactured for the experiment and thus an active headrest against the swept narrowband noise as the primary noise was implemented with a real-time controller in which the VMC algorithm was embedded. After the control experiment with and without the VMC method, the location variation of the ZoQ by analyzing the error signals measured by the error and the virtual microphones. Therefore, it is observed that the FxLMS with the VMC technique can provide the re-location of the ZoQ from the error microphone location to the virtual microphone location. Also it is found that the amount of the attenuation difference between the two locations was small.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.3
• /
• pp.251-260
• /
• 2009

In this paper, we studied on an attenuation effect of automobile exhaust noise according to the direction of canceling speaker in ANC system. Automobile exhaust noise was recorded at 800 rpm, 3500 rpm and 5000 rpm of a diesel engine. Directions of canceling speaker can be set to $30^{\circ}$, $90^{\circ}$ and $150^{\circ}$ against the primary noise flow by acrylic ducts to be made for the experimentation. DSP board with TMS320C6416 chip of Texas Instrument Co. used to control the ANC system. The algorithm of this ANC system applied the Filtered-x-LMS algorithm that is modified to compensate for a property of DSP input signal and the secondary-path effect. As an experiment result, the direction of canceling speaker was proved to influence the reduction effect of noise. The $150^{\circ}$ duct in the attenuation effect of noise showed a better result than the $90^{\circ}$ or $30^{\circ}$ duct.

• Journal of Korean Society of Disaster and Security
• /
• v.16 no.3
• /
• pp.45-56
• /
• 2023

In this study, the application of ANC (Active Noise Control) technology to address inter-floor noise was explored. To achieve this, an ANC system was developed to manage the heavy impact sound within the frequency range of 40 to 500 Hz. The ANC system utilized an adaptive filter employing a feedforward approach based on the Fx-LMS algorithm. To set up the ANC system, a comprehensive analysis of various variables within the system was performed using computational simulations. This process enabled the identification of optimal filter settings and system configuration arrangements. In addition, the ANC system was implemented in the inter-floor noise test room at the Korea Conformity Laboratories (KCL). Through a certified standard testing procedure, it was confirmed that the ANC system led to a 4 dB reduction in inter-floor noise when the system was activated compared to when it was turned off. The results of this study indicate that the developed ANC system has an effect significant enough to elevate the rating criteria by one level for heavy impact sound.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.115-119
• /
• 2011

Instead of very expensive sound record and professional measurement microphones the low cost Surface Mounted Device (SMD) microphones are proposed for practical barrier ANC system. FRF of the microphones and theirs sensitivity to the wind interferences are evaluated in semi anechoic chamber. The improvement of feedforward algorithm noise reduction index was evaluated based on measured coherence function between tested SMD and reference microphone. Test was performed at various wind speed from 1 m/s to 5 m/s.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.16 no.6
• /
• pp.241-246
• /
• 2021

In this paper, we developed the evaluation system for the active noise control so that the algorithms can be easily evaluated in real-time on the system. We implemented the active noise controller based on a single-chip with only additional op-amps for signal conditioning because the TMS320C280049 MCU includes almost all necessary peripherals for the active noise controller. Due to the difficulty in testing algorithms on embedded-type hardware unlike in computer simulation, we also developed GUI-based evaluation software which makes it simple to test algorithms on the hardware. Using the GUI software, we can optimize the parameters of the algorithms with ease in a specific noise environment because the parameters can be adjusted in real-time when the algorithm is running on the hardware.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.41-47
• /
• 2013

PURPOSES : The purpose of this study is about noise which is generated from roads and is consist of irregular frequency variation from low frequency to various band. The existing methods of noise reduction are sound barrier that uses insulation material and absorbing material or have applied passive technology of noise reduction by devices. The total frequency band is needed to apply active noise control. METHODS : In this study applies to the field of road traffic environment, signal processing controller and various analog signal input/output, the amplifier module is based on parallel-core embedded processor designed. DSP performs the control algorithm of the road traffic noise. Noise sources in the open space performance of evaluation were applied. In this study, controller of active signal processor was designed based on the module of audio input/output and main controller of embedded process. The controller of active signal processor operates noise reduction algorithm and performance tests of noise reduction in inside and outside environment were executed. RESULTS : The signal processing controller with OMAP-L137 parallel-core processors as the center, DSP processors in the active control operations dealt with quickly. To maximize the operation speed of an object and ARM processor is external function keys and display for functions and evaluating the performance management system was designed for the purpose of the interface. Therefore the reduction of road traffic noise has established an electronic controller-based noise reduction. CONCLUSIONS : It is shown that noise reduction is effective in the case of pour tonal sound and complex tonal sound below 500Hz by appling to Fx-LMS.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.11 s.104
• /
• pp.1303-1310
• /
• 2005

Stabilization error of target aiming systems mounted on moving vehicles is an important performance because the error directly affects hit Probability. In a heavy load targetaiming system, the disturbance torque comes from mass unbalance and linear acceleration is a main source of stabilization error. This study suggests an experimental design method of disturbance feedforward compensation control to improve the stabilization performance of heavy load target aiming systems. The filtered_x least square(FxLMS) algorithm is used to estimate the compensator coefficients adaptively. The proposed control is applied to a simple experimental set-up which simulates dynamic characteristics of a real target aiming system. The feasibility of the proposedtechnique is illustrated, along with results of experiments.

• Smart Structures and Systems
• /
• v.25 no.5
• /
• pp.559-567
• /
• 2020

Vibration at the tip of various flexible manipulators may affect their operation accuracy and work efficiency. To suppress such vibrations, the feasibility of using MFC actuators and sensors is investigated in this paper. Considering the convergence of the famous filtered-x least mean square (FXLMS) algorithm could not be guaranteed while it is employed for vibration suppression of plants with varying secondary path, this paper proposes a new multiple model switching adaptive control algorithm to implement the real time active vibration suppression tests with a new multiple switching strategy. The new switching strategy is based on a cost function with reconstructed error signal and disturbance signal instead of the error signal from the error sensor. And from a robustness perspective, a new variable step-size sign algorithm (VSSA) based FXLMS algorithm is proposed to improve the convergence rate. A cantilever beam with varying tip mass is employed as flexible manipulator model. MFC layers are attached on both sides of it as sensors and actuators. A co-simulation platform was built using ADAMS and MATLAB to test the feasibility of the proposed algorithms. And an experimental platform was constructed to verify the effectiveness of MFC actuators and sensors and the real-time vibration control performance. Simulation and experiment results show that the proposed FXLMS algorithm based multiple model adaptive control approach has good convergence performance under varying load conditions for the flexible cantilever beam, and the proposed FX-VSSA-LMS algorithm based multiple model adaptive control algorithm has the best vibration suppression performance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.6
• /
• pp.443-453
• /
• 2020

This study using the active vibration control technique attempts to alleviate numerically the airframe vibration of a UH-60A helicopter. The AVCS(Active Vibration Control System) is applied to reduce the 4/rev vibration responses at the specified locations of the UH-60A airframe. The 4/rev hub vibratory loads of the UH-60A rotor is predicted using the nonlinear flexible dynamics analysis code, DYMORE II. Various tools such as NDARC, MSC.NASTRAN, and MATLAB Simulink are used for the AVCS simulation with five CRFGs and seven accelerometers. At a flight speed of 158knots, the predicted 4/rev hub vibratory loads of UH-60A rotor excite the airframe, and then the 4/rev vibration responses at the specified airframe positions such as the pilot seat, rotor-fuselage joint, mid-cabin, and aft-cabin are calculated without and with AVCS. The 4/rev vibration responses at all the locations and directions are reduced by from 25.14 to 96.05% when AVCS is used, as compared to the baseline results without AVCS.