• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.101-102
• /
• 2004

This study was investigated on the impact toughness and microstructure of welded metal and heat affected zone for B grade steel. With welding procedures, welding heat inputs applied were 30, 79 and 264 kJ/cm, Prior austenite grain size in coarse zone has increased with increasing welding heat input for B grade steel. The toughness of fusion line zone of Bgrade steel has decreased with increasing welding heat input while the toughness fusion line +3 and +5 mm zone increased contrarily.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2004년도 추계학술발표회 발표논문집
• /
• pp.867-868
• /
• 2004

The maximum width of HAZ of SA508치.3 steel produced by overlay RPV cladding was approximately 10 mm and it was composed of variety of microstructures with various grain size and precipitates. In addition, along the weld fusion line there formed a heavy carbide precipitation zone in the width of $20{\sim}30\;{\mu}m$. 2. As the specimen sampling position approached to the weld fusion line, the increase in yield and tensile strength was approximately 90 and 40 MPa, respectively. Meanwhile, the plastic fracture strain reduced from 14 to 8 percent. 3. The lowest SP energy and the highest ductile to brittle transition temperature in the HAZ were observed at the coarse- and fine-grained HAZ.

• Journal of Welding and Joining
• /
• 제16권4호
• /
• pp.83-91
• /
• 1998

Cracking problems which high temperature plant components suffer during long-term service, occur very often at welded locations. The crack occurs due to accumulated creep damage near fusion line or at heat affected zone (HAZ). However, most of the studies on creep crack growth behavior have been performed with matrix metal not wit welded metal due to the difficulty of interpreting the test results. In this study, creep crack growth rates were measured with C(T) specimens whose cracks were formed along the fusion line or HAZ. The measured crack growth rates were characterized by {TEX}$C_{t}${/TEX}-parameter derived for elastic-primary-secondary creeping material. Since contribution of primary creep was significant for the tested 1Cr-0.5Mo steel, its effect was carefully studied. Effects of crack tip plasticity and material aging were also discussed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.152-154
• /
• 2005

Austenitic stainless steel has good weldability but is sensitive to hot cracking such as solidification crack and liquation crack. In this study, the specimens of dissimilar metals made between austenitic stainless steel and Al-brass were welded by GTAW process using four different filler metals. Cracks were detected in the heat-affected zone of the stainless steel when welded with CuAl, CuSn and NiCu filler metals, but no cracks were detected a Ni filler metal was used. The cracks propagated along the grain boundary in the heat affected zone near the fusion line to base metal of 316L stainless steel. The cracks were located inside the weld bead with very fine hairline crack. All cracks initiated at the fusion line and moved forward in the base metal. From energy dispersion spectroscopy (EDS), Cu peak was detected only in the crack-opening area.

• 대한소아치과학회지
• /
• 제24권4호
• /
• pp.795-804
• /
• 1997

Developmental dental morphological anomalies are fusion, gemination, twinning, concrescence and etc. They may cause many problems in conservative, periodontal and esthetic aspects. Fusion is a condition where two separate tooth buds unite at some stage in their development to form a bifid crown. If tooth contact occurs early, at least before the start of calcification, the two teeth may be completely unites to form a single large tooth. If tooth contact occurs after the time when a portion of the tooth crown has completed its formation, there may be union of the roots only. In fusion the dentin is always confluent. Fusion teeth is more common in the deciduous than in the permanent dentition. Fused teeth are relatively rare, and are mostly mandibular anterior teeth. Fusion of normal and supernumerary teeth or between normal teeth may occurs. The exact etiology factor of fusion is unknown, but genetic and environmental factors seems to be related. A variety of complications and subsequent treatments have been suggested on this teeth. Periodontal conditions may arise due to a groove formed at the line of fusion of the two teeth. Crowding or Protrusion with potential for malocclusion or delayed eruption of adjacent teeth. Fusion teeth appear in the anterior region, they usually cause esthetic problems. Treatments vary depending on the problem, the location, and the extent of fusion. Treatment of fused teeth has been reported from endodontic, orthodontic, periodontic, surgical and multidisciplinary. This report presents the esthetic improvements by separation of two clinical crowns. Bone reduction or endodontic treatments are not required.

• IMMUNE NETWORK
• /
• 제3권4호
• /
• pp.302-309
• /
• 2003

Background: CTLA4 (CD152), which is expressed on the surface of T cells following activation, has a much higher affinity for B7 molecules comparing to CD28, and is a negative regulator of T cell activation. In contrast to stimulating and agonistic capabilities of monoclonal antibodies specific to CTLA-4, CTLA4Ig fusion protein appears to act as CD28 antagonist and inhibits in vitro and in vivo T cell priming in variety of immunological conditions. We've set out to confirm whether inhibition of the CD28-B7 costimulatory response using a soluble form of human CTLA4Ig fusion protein would lead to persistent inhibition of alloreactive T cell activation. Methods: We have used CHO-$dhfr^-$ cell-line to produce CTLA4Ig fusion protein. After serum free culture of transfected cell line we purified this recombinant molecule by using protein A column. To confirm characterization of fusion protein, we carried out a series of Western blot, SDS-PAGE and silver staining analyses. We have also investigated the efficacy of CTLA4Ig in vitro such as mixed lymphocyte reaction (MLR) & cytotoxic T lymphocyte (CTL) response and in vivo such as experimental autoimmune encephalomyelitis (EAE), graft versus host disease (GVHD) and skin-graft whether this fusion protein could inhibit alloreactive T cell activation and lead to immunosuppression of activated T cell. Results: In vitro assay, CTLA4Ig fusion protein inhibited immune response in T cell-specific manner: 1) Human CTLA4Ig inhibited allogeneic stimulation in murine MLR; 2) CTLA4Ig prevented the specific killing activity of CTL. In vivo assay, human CTLA4Ig revealed the capacities to induce alloantigen-specific hyporesponsiveness in mouse model: 1) GVHD was efficiently blocked by dose-dependent manner; 2) Clinical score of EAE was significantly decreased compared to nomal control; 3) The time of skin-graft rejection was not different between CTLA4Ig treated and control group. Conclusion: Human CTLA4Ig suppress the T cell-mediated immune response and efficiently inhibit the EAE, GVHD in mouse model. The mechanism of T cell suppression by human CTLA4Ig fusion protein may be originated from the suppression of activity of cytotoxic T cell. Human CTLA4Ig could not suppress the rejection in mouse skin-graft, this finding suggests that other mechanism except the suppression of cytotoxic T cell may exist on the suppression of graft rejection.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2007년도 제33회 하계학술대회 초록집
• /
• pp.188-188
• /
• 2007

• 한국융합학회논문지
• /
• 제6권1호
• /
• pp.1-5
• /
• 2015

본 논문에서는 Wi-Fi신호로 제어되는 융합형 라벨기 설계에 대하여 기술하였다. 현재 산업체에서 사용되는 라벨기는 산업현장에서 단독 장비로만 사용되고 인터넷이나 다른 네트웍 연결을 가지고 있지 않아서 라벨기가 수집한 자료를 전송하는 기능이 없어서 매우 불편하였다. 본 연구에서는 라벨기가 작업한 라벨의 종류와 사용량을 실시간 Wi-Fi를 사용하여 서버 컴퓨터로 전송할 수 있도록 정보통신(IT) 융합기술을 이용하여 설계하였다. 이러한 융합형 라벨기 시스템은 서버 컴퓨터에서 실시간으로 작업량과 작업상태를 파악할 수 있어서 기존 라벨기를 사용하는 경우보다 작업능력을 향상시키고 실시간으로 품질을 파악할 수 있게 되었다.

• 한국산학기술학회논문지
• /
• 제13권12호
• /
• pp.6022-6026
• /
• 2012

본 논문은 마이크로스트립 전송선로에 삽입된 주파수 선택 표면(FSSs)을 사용하여 주기적인 구조를 갖는 대역저지필터(BSF)에 관한 것이다. 제안된 대역저지필터는 변형된 크로스 루프 슬롯 (Cross-loop slot)을 단위 셀로 하여 주기적인 구조로 설계하였으며, 설계된 대역 저지 필터는 등가회로 모델과 분산 도표(dispersion diagram)로 해석하였다. 대역 저지 필터의 중심주파수(fo)는 6.6 GHz이다. 제안된 필터는 단위 셀의 개수가 증가하면 3dB 대역폭은 넓어지고 삽입손실은 줄어드는 특성이 있다. 또한 제안한 대역저지필터는 소형의 평면구조를 가지며, 한 번의 에칭으로 제작이 가능 하여 다양한 분야의 RF 필터로서 사용 가능성이 높다.

• 대한교통학회지
• /
• 제19권6호
• /
• pp.171-182
• /
• 2001

본 연구는 지점검지체계와 구간검지체계와의 자료합성을 통하여 도심 간선도로 및 지방도로 구간별 효과척도를 산정할 뿐만 아니라 유고검지 및 통행패턴 예측, 네트워크 기종점에 대한 최적/최단 경로를 탐색하는데 기초가 되는 구간 통행시간 추정을 수행한다. 개개 수집원의 자료합성을 위해 퍼지이론과 인공신경 망의 합성모형인 FALEM(Fuzzy Adaptive Learning Estimator for travel time from Multi-information sources)을 개발, 개발된 모형 FALEM에 의해 개개구간의 통행시간을 산출하고 동일시간, 동일구간에서 조사된 실측데이터와의 오차율 비교를 통해 추정된 통행시간을 검증하였다. 테스트 환경은 개발모형에 의해 추정된 구간 통행시간의 적용성을 고려하여 실시간 운영하에서 수행되었다.