• Journal of Welding and Joining
• /
• 제27권3호
• /
• pp.73-79
• /
• 2009

This present paper investigated the mechanical properties and the microstructures of each penetration shapes classifying the conduction shape area and the keyhole shape area about electron beam welded 120(T)mm thick plated aluminum 5052 112H. As a result the penetration depth is increased linearly according to the output power, but the aspect ratio is decreased after the regular output power. In the conduction shape area, the Heat affected zone is observed relatively wider than the keyhole shape area. In the material front surface of the welded specimen, the width is decreased but the width in the material rear surface is increased. After the measuring the Micro Vikers Hardness, it showed almost similar hardness range in all parts, and after testing the tensile strength, the ultimate tensile strength is similar to the ultimate tensile strength of the base material in all the specimens, also the fracture point was generated in the base materials of all the samples. In the result of the impact test, impact absorbed energy of the Keyhole shape area is turned up very high, and also shown up the effect about four times of fracture toughness comparing the base material. In the last result of observing the fractographs, typical ductile fraction is shown in each weld metal, and in the basic material, the dimple fraction is shown. The weld metals are shown that there are no other developments of any new chemical compound during the fastness melting and solidification.

• 한국터널지하공간학회 논문집
• /
• 제22권6호
• /
• pp.623-641
• /
• 2020

터널식 전력구는 약 5 km 이내의 연장을 기계식 굴착장비인 밀폐형 쉴드TBM을 이용하여 건설된다. 공기지연 예방 및 적기가압을 위해서는 암반등급별 공사기간의 예측정확도를 향상시켜야하며, 투입된 장비의 성능을 고려한 최적운전이 필수적이다. 이에 본 연구에서는 3.6 m급 쉴드TBM에 적합한 순굴진율 모델을 개발하고자 실대형 굴진시험을 수행하였다. 대표적인 일축압축강도에 대해서 소요추력과 커터헤드 회전속도를 바탕으로 약 100회의 실험을 수행하였다. 이에 풍화암, 연암, 경암분류에 따라 일축압축강도와 장비의 소요추력 조건이 고려된 연직력과 압입깊이 및 일축압축강도와 토크와의 상관관계를 제시하였다. 개발된 순굴진율 모델을 바탕으로 구동부 성능분석과 최적운전 조건에 대해 제시하였다. 본 연구결과를 통해 터널식 전력구 공사기간 단축 및 조기사용에 대한 사용자 편익증대를 기대할 수 있다.

• KEPCO Journal on Electric Power and Energy
• /
• 제6권3호
• /
• pp.305-313
• /
• 2020

전력송전을 위한 터널식 전력구는 점차 시공실적이 증가하고 있는 추세이며, 해저 및 대심도 등 시공환경이 어려운 구간의 건설도 증가하고 있다. 이에 소단면 쉴드TBM의 효율적 운영을 위해 굴진율 및 설계모델이 필요하다. 그러나, 제한된 지반조사 회수 및 굴착면 맵핑으로 인하여 암반특성과 굴진데이터를 정확히 매칭시켜 상호간 상관관계 및 굴진율 모델을 도출하는데 어려움이 있다. 이에 소단면 쉴드TBM에 적합한 굴진율 및 설계모델을 제시하기 위하여 커터헤드의 직경이 3.56 m인 실험용 EPB 쉴드TBM을 제작하고, 총 부피 87.5 ㎥인 인공암반 내에서 총 19번의 실대형 굴진실험을 수행하였다. 본 실험은 70MPa의 균질한 암반강도에서 수행되었기 때문에 운전변수인 추력과 커터헤드의 RPM에 따른 굴진율과 기계데이터간 상관관계를 효율적으로 분석할 수 있으며, 실제 굴착메커니즘과 동일하기 때문에 도출된 압입깊이와 토크값은 활용성이 높다. 본 연구를 통해 디스크커터 당 연직력과 압입깊이의 상관관계 및 연직력과 회전력의 상관관계를 도출하였다. 이러한 상관관계들을 이용하여 70 MPa급 암반에 대해 굴진율 예측과 TBM 설계가 가능할 것으로 판단한다. 또한, 인공암반의 RQD가 100%로 현장적용에 대한 한계점에 대해 FPI의 개념을 도입하여 굴진율 모델의 활용성을 증대시키고자 하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.405-414
• /
• 1999

The auger and screw piles have known an important evolution during the last decade. Besides the large success of augercast (CFA) piling systems, new systems have been developed combining, to a variable extent, the classical extraction auger with especially designed displacement tools in order to develop screw piles with partial or total lateral soil displacement. These last developments cover the whole range of lateral soil displacement and are more difficult than ever to compare. The authors present the latest evolutions in auger piling systems and compare them with respect to penetration performances, bearing capacities and amount of spoil generated. A special focus is given to a new efficient system: the OMEGA(H) pile in use in Korea since 1997. The results of the Hongcheon site are presented where this R system was applied for a new investment of the Korean National Housing Corporation (KNHC). This first important experience, with the execution of some 1,500 Omega piles with diameter 410 mm, is presented. The piles were installed through loose silty sands down to very dense sands and layers of gravel. The results of full-scale load tests are analysed and show the conformity with requirements of the clients.

• Journal of Welding and Joining
• /
• 제29권1호
• /
• pp.90-98
• /
• 2011

Al-Si coated Boron steel and Zn coated DP steel were welded using DISK laser and the microstructure and hardness of the weld were investigated. Full penetration was obtained, when the welding speed was lower than 4m/min. In the specimen welded with laser power of 3 kW and welding speed of 2 m/min, the hardness was the highest in the heat affect zone in the boron steel (HAZ-B) and that of the heat affect zone in the DP steel (HAZ-D) was lower than HAZ-B. The hardness of fusion zone was in between those of HAZ-B and HAZ-D. The decreased hardness from each HAZ to base metal(BM) could be explained that ferrite contents increases when access to the BM. The variation of hardness in the welds could be explained by the difference of microstructure, that is, full martensite in HAZ-B, mixture of martensite and bainite in the fusion zone, and the mixture of martensite, ferrite and bainite in HAZ-D.

• Bulletin of the Korean Chemical Society
• /
• 제18권4호
• /
• pp.385-389
• /
• 1997

We report on the development of a new method to control the coverage of a metal film prepared with immersion method. An Sb species in solution adsorbed irreversibly at an open circuit potential (∼0.2 V) as an oxygenous Sb(Ⅲ) on a clean Au electrode, and the adsorbates showed voltammetric features in the potential range from 0.1 V to - 0.4 V. The full coverage of the Sb adsorbates was ∼0.45. On the contrary, the Sb species in solution did not adsorb at all on iodine-covered Au electrode surfaces, when the iodine coverages were more than 0.25. As the iodine coverage decreased below 0.25, however, the irreversible adsorption of Sb took place and the coverage of Sb increased accordingly. This electrochemical behavior has been interpreted as the penetration of the adsorbing Sb species in solution through open spaces among the iodine adlattices of coverages less than 0.25. With the manipulation of the iodine coverage, the controllable range of Sb coverage was from 0 to 0.45, i.e. the full coverage of Sb. In addition, the reversible deposition of Sb on an iodine-saturated Au electrode with voltammetric scan has been observed, which is contrasted with the adsorptive behavior of Sb on the clean Au electrode.

• 한국방사선학회논문지
• /
• 제17권2호
• /
• pp.175-184
• /
• 2023

검출기의 실제 모양과 제조사에서 제공한 데이터를 기준으로 Penelope simulation을 통해 검출기 모양을 구현하며 측정치에서 얻은 효율을 기준으로 하여 적합한 사층 두께에 적용하였다. 검출기의 simulation 된 전체에너지피크 효율 채널수와 crystal의 Outside contact layer가 전체에너지피크 효율에 미치는 영향을 결정 하기위한 효율 계산은 Penelope Code를 사용하여 0.3, 0.5, 0.7, 1.0, 1.2 ,1.4 mm의 다양한 사층 두께에 대해 수행하였다. 외부 접촉 사층 두께가 5배 증가하였을 때, 59.50 keV의 경우 전체에너지피크 효율이 약 36% 감소하였으며, 1836.01 keV 경우 10% 감소하였다. 또한 10배 증가할수록 59.54 keV의 경우 FEP 효율이 약 20% 감소하였으며, 1836.01 keV 경우 7% 감소하였음을 확인하였다. Penelope simulation된 전체에너지피크 효율 채널은 사층 증가에 따라 기하급수적으로 감소한다. 또한, 총 효과 곡선은 0.3 - 1.4 mm 사층 두께 영역에서 3.5% 미만의 상대적 차이로 잘 일치함을 확인하였다. 그러나 비균질 사층이 몬테카를로 모델에서 여전히 매개변수라는 것을 알 수 있었다.

• The Plant Pathology Journal
• /
• 제33권1호
• /
• pp.95-100
• /
• 2017

Fungicide-resistant Alternaria alternata impede the practical control of the Alternaria diseases in crop fields. This study aimed to investigate cytological fungicide resistance mechanisms of A. alternata against dicarboximide fungicide iprodione. A. alternata isolated from cactus brown spot was cultured on potato-dextrose agar (PDA) with or without iprodione, and the fungal cultures with different growth characteristics from no, initial and full growth were observed by light and electron microscopy. Mycelia began to grow from one day after incubation (DAI) and continued to be in full growth (control-growth, Con-G) on PDA without fungicide, while on PDA with iprodione, no fungal growth (iprodione-no growth, Ipr-N) occurred for the first 3 DAI, but once the initial growth (iprodione-initial growth, Ipr-I) began at 4-5 DAI, the colonies grew and expanded continuously to be in full growth (iprodione-growth, Ipr-G), suggesting Ipr-I may be a turning moment of the morphogenetic changes resisting fungicidal toxicity. Con-G formed multicellular conidia with cell walls and septa and intact dense cytoplasm. In Ipr-N, fungal sporulation was inhibited by forming mostly undeveloped unicellular conidia with degraded and necrotic cytoplasm. However, in Ipr-I, conspicuous cellular changes occurred during sporulation by forming multicellular conidia with double layered (thickened) cell walls and accumulation of proliferated lipid bodies in the conidial cytoplasm, which may inhibit the penetration of the fungicide into conidial cells, reducing fungicide-associated toxicity, and may be utilized as energy and nutritional sources, respectively, for the further fungal growth to form mature colonies as in Ipr-G that formed multicellular conidia with cell walls and intact cytoplasm with lipid bodies as in Con-G.

• 기술사
• /
• 제17권4호
• /
• pp.28-39
• /
• 1984

Experiments were carried out for the development of a processing method of soybean into full-fat or defatted flour, using two varieties of soybean (kwangkyo produced in Korea and Bragg produced in India) Samples were subjected to dry dehulling, size reduction and wet heat treatment processes to make soybean flours. The quality of soybean flours were evaluated, and the results obtained were summarized as follows. 1. Crude fiber content of dehulled soybean was under 3.0% which indicated satisfactory dehulling, and there was no significant difference in crude fibre content between two varieties. 2. When dehulled soybean was cracked into soy grits by a hammer mill, 98.71∼98.86％ of the soy grit was in the range of 10∼18 mesh which was the optimum size of particle for quick and uniform penetration of heat into the intra-particle air spaces. 3. Moisture content of soy flour after steam treatment at 15 psig for 5 to 30 min was only 0.29∼1.68% which did not hinder the next milling operation. 4. From the color analysis of soy flours, it was observed that the dominant wavelength for all the samples are in a very narrow range from 575 to 581 nm and the color variation was from yellow to yellowish orange. Twenty to twenty five ％ higher reflectance was observed in the defatted flours than full fat flours. The ％ chroma of the defatted flour slightly increased as the duration of steaming of soy grits increased, whereas that of the full-fat flour did not. 5. The protein extractability in the defatted flour at pH 7.6 showed progressive decrease in solubility from 48.40％ (Bragg), 75.20％ (kwangkyo) for untreated flours to 9.75％ (Bragg), 26.27％ (kwangkyo) for 30 min steaming. But Kwangkyo variety showed twice higher protein extractability than Bragg variety.

• 비파괴검사학회지
• /
• 제18권1호
• /
• pp.42-45
• /
• 1998

원유 또는 가스 생산을 위해 해상에 설치되는 플랜트 해양설비는 크게 jacket과 module로 나눌 수 있다. Jacket은 module을 지지하기 위한 구조물로써 jacket 본체와 pile로 구성되어 있으며, 미국용접학회(AWS)의 규정에 의해 대부분의 맞대기 완전용접 이음부(full penetration butt welds)에 대해 100% 방사선투과검사를 실시하게 되어 있다. 그러나 지금까지 방사선투과검사를 실시해 온 경험으로 미루어 볼 때 방사성에 대한 안전성, 생산공정의 영향(검사지연) 등 방사선투과검사는 많은 문제점을 가지고 있었다. 이에 대한 문제점을 해소하고, 국내의 비파괴검사 기술 향상을 위해 자동 초음파탐상 system을 개발, 방사선투과검사를 자동 초음파탐상검사로 대체하여 적용한 사례를 간략하게 기술하였다. 또한, 적용 확대를 위해 개방중인 system을 소개하고 아울러 자동 초음파탐상기술에 대한 앞으로의 방향을 제시하였다.