• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.8 s.227
• /
• pp.1203-1211
• /
• 2004

A traction control systems (TCSs) composed of either a wheel slip controller or a throttle valve controller or an integrated controller of both systems are proposed in this study. To validatethe dynamic characteristics of a vehicle and TCS, a full car model that can simulate the responses of both front wheel drive (2WD) and four wheel drive (4WD) vehicle is also developed. The wheel slip controller uses a sliding mode control scheme and the throttle valve is controlled by a PID controller. The results shows that tHe brake TCS and the engine TCS achieve rapid acceleration, and reduce slip angle on slippery road. When a vehicle is cornering and accelerating maneuver with the brake or engine TCS, understeer or oversteer occur, depending on the driving conditions. The integrated TCS prevents most of these problems and improves the stability and controllability of the vehicle.

• Journal of Mechanical Science and Technology
• /
• v.20 no.6
• /
• pp.874-881
• /
• 2006

Combustion stability characteristics in actual full-scale combustion chamber of a rocket engine are investigated by experimental tests with the model (sub-scale) chamber. The present hot-fire tests adopt the combustion chamber with three configurations of triplet impinging-jet injectors such as F-O-O-F, F-O-F, and O-F-O configurations. Combustion stability bound-aries are obtained and presented by the parameters of combustion-chamber pressure and mixture (oxidizer/fuel) ratio. From the experimental tests, two instability regions are observed and the pressure oscillations have the similar patterns irrespective of injector configuration. But, the O-F-O injector configuration shows broader upper-instability region than the other configurations. To verify the instability mechanism for the lower and upper instability regions, air-purge acoustic test is conducted and the photograph or the flames is taken. As a result, it is found that the pressure oscillations in the two regions can be characterized by the first impinging point of hydraulic jets and pre-blowout combustion, respectively.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.1
• /
• pp.63-67
• /
• 1985

KIA는 호평의 Bongo-9을 기본 model로 하여 도시형 다목적 leisure car인 Bongo-town을 개 발하게 되었다. TX엔진은 Bongo-town 탑재용으로 기존 1.3l TC 엔진을 volume-up 하여 전 회전 영역에서 괄목할 성능향상을 보였으며 특히 탑재차량의 특성을 고려하여 저속영역 torque를 강조하였고 부품호환성 및 생산 설비의 공용화에도 주력했다. 주요 개발내용은, 1) Cooling passage 개선 및 full siamese화 2) Piston과 connecting rod의 신설계 3) Piston 조합의 semi floating화 4) Cam shaft profile 선정 및 valve timing 변경 5) Distributor 최적진각특성 결정 6) Carburetor 개발 7) Torque limited fan and fan drive 채용 등이다. 상기내용중 중요한 몇가지를 기술하고자 한다.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.684-689
• /
• 2000

In this paper, the equations of motion about vehicle, powertrain and brake system were derived. The vehicle has eight degrees of freedom with nonlinear tire model and the powertrain has two degrees of freedom containing engine, torque converter and four speed automatic transmission. The brake system has two states about front and rear brake line pressures. The transient tire model with first order time lag is also subjoined for low speed or stop-and-go simulation. The modeling was derived considering two points - the fidelity and the simplicity. The simulation using this model is similar with real vehicle dynamic behavior and the model is made as simple as possible far fast simulation. It is validated that the derived vehicle model can be applicable to the real time simulation.

• Proceedings of the Korean Information Science Society Conference
• /
• 2001.04b
• /
• pp.22-24
• /
• 2001

A new GIS software Spatial Database Engine(SDE) has been developed to integrated with spatial database that combines conventional and spatially related data. As we known well in the traditional relation database system, the query evaluation techniques are a well-researched subject, many useful and efficient algorithms have been proposed, but in the spatial database system, it is a litter difference with the traditionally ones. Based on the Query Graph Model(QGM), we implemented our own query evaulation plan in the SDE, which can deal with the full functionality query statement SELECT-FROM-WHERE_GROUPBY-HAVING, and treat the spatial data and non-spatial data seamlessly. We proposed a novel multi way join algorithm base on nest loop that may be attractive.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.267-275
• /
• 1998

In this study, the instantaneous heat flux measurement probe and the linkage system for the measurement of the instantaneous temperature and heat flux of the DI mono cylinder diesel engine were developed, and these were proved to have a good reliability and sensibility. A 3-D FEM model which consist of full piston to accommodate the eccentric bowl in the piston head, was applied for the analysis of the thermal stress and the temperature distribution. The mean heat flux on the piston head was used as boundary condition for the analysis of piston. The analysis showed that thermal stress concentrate on the bowl and inner surface of pin hall.

• Journal of Mechanical Science and Technology
• /
• v.18 no.6
• /
• pp.1010-1018
• /
• 2004

This study presents the methodological aspects of combustion instability modeling and provides the numerical results of the model (sub-scale) combustion chamber, regarding geometrical dimensions and operating conditions, which are for determining the combustion stability boundaries using the model chamber. An approach to determine the stability limits and acoustic characteristics of injectors is described intensively. Procedures for extrapolation of the model operating parameters to the actual conditions are presented, which allow the hot-fire test data to be presented by parameters of the combustion chamber pressure and mixture (oxidizer/fuel) ratio, which are customary for designers. Tests with the model chamber, based on the suggested scaling method, are far more cost-effective than with the actual (full-scale) chamber and useful for injector screening at the initial stage of the combustor development in a viewpoint of combustion instabilities.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.6
• /
• pp.722-728
• /
• 1998

In this paper real-time estimation methods for identifying the tire-road friction coefficient are presented. Taking advantage of the Magic Formula Tire Model, the similarity technique and the specific model for the vehicle dynamics, a reduced order observer/filtered-regressor-based method is proposed. The Proposed method is evaluated on simulations of a full-vehicle model with an eight state nonlinear vehicle/transmission model and nonlinear suspension model. It has been shown through simulations that it is possible to estimate the tire-road friction from measurements of engine rpm, transmission output speed and wheel speeds using the proposed identification method. The proposed method can be used as a useful option as a part of vehicle collision warning/avoidance systems and will be useful in the implementation of a warning algorithm since the tire-road friction can be estimated only using RPM sensors.

• Journal of Mechanical Science and Technology
• /
• v.19 no.9
• /
• pp.1821-1832
• /
• 2005

This study realizes the conceptual method to predict combustion instability in actual full-scale combustion chamber of rocket engines by experimental tests with model (sub-scale) chamber. The model chamber was designed based on the methodologies proposed in the previous work regarding geometrical dimensions and operating conditions, and hot-fire test procedures were followed to obtain stability boundaries. From the experimental tests, two instability regions are presented by the parameters of combustion-chamber pressure and mixture (oxidizer/fuel) ratio, which are customary for combustor designers. It is found that instability characteristics in the chamber with the adopted jet injectors can be explained by the correlation between the characteristic burning or mixing time and the characteristic acoustic time: In each instability region, dynamic behaviors of flames are investigated to verify the hydrodynamically-derived characteristic lengths of the jet injectors. Large-amplitude pressure oscillation observed in upper instability region is found to be generated by lifted-off flames.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.4
• /
• pp.85-92
• /
• 2006

A design program has been developed to predict film cooling performance of a liquid rocket engine. A thermal protecting effect of low mixture ratio gas layer has been analysed by CFD. A one-dimensional film cooling model based on the CFD results has been implemented to the previously developed design program of regenerative cooling. Satisfactory agreement has been achieved by comparing the predicted maximum heat flux at the throat of a subscale chamber and the average measured value, and the predicted nozzle average heat flux and the measured value for a full scale chamber with film cooling. It is ascertained that the film cooling is effective to reduce the throat heat flux in rocket engine chamber.