• Journal of Biosystems Engineering
• /
• 제34권2호
• /
• pp.71-76
• /
• 2009

This study was conducted to investigate the load acting on a tractor engine when it delivers the maximum power at drawbar. The results of the drawbar tests on the 5 locally-made and 14 imported tractors conducted at NIAE in 2004, and the 15 tractors tested at OECD test stations in foreign countries were analyzed and presented by the torque load ratio, defined as a ratio of the engine torque load caused by drawbar pull to its full-load capacity, as a function of pull speed. The NIAE test results showed that the torque load ratio increased from 20 to 80% with pull speed less than 5 km/h. At speeds faster than 5 km/h, it was 80${\sim}$110% regardless of the pull speed. However, the OECD test results showed that the torque load ratio was evaluated mostly to be 70${\sim}$90% in the entire pull speed range. The same trend was also shown for the maximum drawbar load. The difference in the torque load ratio may be attributable to bias-ply tires for locally-made and some imported tractors. It is also suggested that the input torque load may be increased safely up to 120% of the full load capacity of the tractor engine for an accelerated life test of tractor transmissions.

• 한국군사과학기술학회지
• /
• 제12권3호
• /
• pp.388-395
• /
• 2009

Surveillance Radar System for naval vessels is a primary core sensor for command and fire control, and provides CFCS(Command and Fire Control System) information for 3-D surveillance and fire control. It's composed of Antenna, Transmitter/Receiver, Signal Processor, and Air drier, which are installed on and under deck. They should be designed and produced in order to endure at any operating circumstances. This paper analyzes load of a driving part for driving the antenna considering factors under external operating circumstances, and proposes a condition of load for maintaining fixed RPM through analyzing internal load of the driving part, and how to reduce the load to meet the condition. This paper is verified through experimental studies.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.58-66
• /
• 2012

This paper describes a design and a verification of linear state observers for a motorized seat belt system to estimate state information such as angular velocity and load torque. The motorized seat belt system provides functions to protect passengers and improve passenger's convenience. To realize these functions, sensors which can measure an angular velocity and load torque are needed. By use of the linear state observer, state information can be estimated without sensors. The motorized seat belt system is analysed and represented as a state space model which contains load torque as an augmented state. By the developed state space model, a full and reduced order observer are designed and verified by experiments. The full and reduced order observer are also compared from points of view of execution time and noise robustness.

• Journal of Biosystems Engineering
• /
• 제16권2호
• /
• pp.124-132
• /
• 1991

This study was carried out to obtain the information needed in the development of forward speed control system and the improvement of combine performance. The effects of variety, grain moisture content and forward speed on the combine load characteristics were investigated through experiments. The results of this study are summarized as follows. 1. A data acquisition system was developed to measure the engine speed and the torques and speeds of the threshing cylinder, dean-grain auger and tailings-return auger. The system consisted of transducers, signal conditioner, interface board and microcomputer. The system accuracy is better than ${\pm}2.3%$ full scale. 2. Linear regression equations were obtained for the torque, speed and power requirement of threshing cylinder for different paddy varieties, grain moisture contents and feed rates. 3. The maximum value of relative frequency for threshing cylinder torque decreased as the increase in feed rate and moisture content. The range of torque fluctuation was 1.2~3.7 and 1.2~1.9 times the average and maximum torque, respectively. The maximum value of power spectrum density (PSD) appeared to be about 11 Hz regardless of paddy variety, grain moisture content and feed rate. 4. The speed of tailings return thrower decreased rapidly at below 900rpm, and it fell to near zero about 3 seconds after that time. When the travelling of combine harvester was stopped immediately after sensing the overload, it took about 7 seconds for a full recovery of the no-load speed of tailings return thrower.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권2호
• /
• pp.148-154
• /
• 2014

This paper describes problems of the sensorless starting of horizontal axis washing machines with direct drive and suggests solution, which was experimentally verified. Horizontal axis washing machines have very difficult conditions for the drive starting, especially at full load. Inertia of the tub and water, torque from the laundry make load torque at starting higher than rated one and sometimes even higher than the maximum torque of the motor, which makes sensorless starting extremely challenging task. This paper suggests modified open-loop starting, where control system is closed shortly after beginning at low speed and rotates the drum until laundry restructuring. To ensure proper work of the sensorless algorithm at low speed additional measures for increasing of the estimation algorithm performance have been taken. These measures include special algorithm for the drive parameters estimation, which has been developed and verified by the experimental results.

• 한국정밀공학회지
• /
• 제17권5호
• /
• pp.100-107
• /
• 2000

The hydraulic couplings have been widely used in industries, automobile, and power-station drives including ships. A mathematical analysis by which the design and application of hydraulic couplings are made is used in conventional design formulae and general roto-dynamic theories. The fluid flow of hydraulic couplings can be considered to have two component, one circumferentially about the coupling axis, and the other passing fluid from the pump to the turbine in the plane of the coupling axis. Tests have been carried out on the full-scale production coupling. The performance test consists of taking measurement of torque of the fluid coupling for three different amount of working fluid inside with various loads to the output shaft. The purpose of this research is to construct the experimental test equipments and to establish a series of performance test for the domestically developed hydraulic couplings, and to obtain experimental results which can be used to improve the performance of the hydraulic coupling and to solve the practical problems confronted in operation.

• 조명전기설비학회논문지
• /
• 제19권1호
• /
• pp.70-79
• /
• 2005

본 논문은 축소차원 상태방정식을 사용한 전차원 관측기를 이용하여 저속도 영역에서의 운전 성능 개선방법을 제안하였다. 축소차원 상태방정식을 사용한 전차원 관측기는 간단한 모터속도 및 외란토크 관측기이다. 제안한 알고리즘은 약 1.9[rpm]의 저속도에서 매우 안정적인 결과를 보였다. 모터구동 시스템에서 외란토크는 저속도 영역에서 속도제어 성능을 저하시킨다. 제안한 알고리즘은 모터속도와 외란토크를 모두 추정한다. 추정된 외란 토크는 속도제어기의 출력에 전향보상 값으로 사용되며, 그 결과 저속도 영역(1.9rpm)에서 부하토크 응답특성이 향상된 것을 확인하였다.

• 한국항공우주학회지
• /
• 제38권6호
• /
• pp.537-546
• /
• 2010

본 연구는 최근 금속재를 대체하기 위하여 RTM법으로 개발된 헬리콥터 복합재 토크링크 구조에 대하여 피로 내구성 평가 절차와 기법에 대하여 고찰하였다. 피로내구성 평가에 필요한 운용수명 중 예상되는 피로하중스펙트럼을 산출하는데 보다 신뢰성이 높은 진보된 기법으로 확률적 랜덤처리 기법을 도입하였다. 그리고 불균질성이 큰 복합재에 대하여 재료의 피로특성치를 기반으로 하는 강도저하 접근법을 통하여 잔여강도와 피로파손확률 거동을 분석함으로써 보다 신뢰성 있는 내구성 평가를 수행하였다. 이때 강도저하파라미터 는 일련의 재료시편 피로시험 결과를 최대근사법을 사용하여 Weibull 파라미터를 해석함으로써 결정하였다. 또한 복합재 토크링크 실물시제에 대하여 피로내구성 시험을 수행하고 해석결과와 비교 검토하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부A
• /
• pp.37-39
• /
• 1998

The hybrid step motor has found applications in a wide range of mechanical systems as a low cost, open-loop positioning device. The step motor provides good stiffness at rest against disturbing load influences, a combination of moderate speed fine resolution, high reliability and simplicity. In recent years, considerable competition has arisen over the technological issue of wheather the device should be applied as a 2-Phase or 5-Phase machine. In this paper, to compare two systems, we have atempted to derive the mathematical. model, and analysed operating detent torque with this model. The analysis shows that a fundamental component of the permeance distribution produces the average torque and that harmonic components produce the ripple torque.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.576-578
• /
• 1994

In this. paper, a new technique to estimate both the instantaneous speed and disturbance load torque using a low precision shaft encoder in very low speed range is proposed. To detect the instantaneous speed and disturbance load torque, the Kalman filter which is an optimal full order estimator is used. Experimental results conform the validity of the proposed estimation technique. The effects of parameter variations are discussed, and it is verified that the system is robust to the modeling error.