• 한국환경농학회지
• /
• 제26권1호
• /
• pp.1-6
• /
• 2007

본 연구에서는 바이오가스의 연소엔진을 이용한 에너지 전환시에 발생되는 $NO_x$와 CO의 배출특성을 분석하고 나아가 배출계수를 산정하고자 하였다. 바이오가스의 주성분인 메탄을 70%로 한 합성가스를 이용하여 실험한 결과 연소엔진의 표준상태에서 $NO_x$와 CO가 각각 4 ppm과 100 ppm의 배출농도를 나타내었고, 이는 1.29g/MMBtu와 30.86 g/MMBtu의 배출계수 값을 산정할 수 있었다. 바이오가스의 주성분인 메탄을 60%로 한 약간의 과잉공기의 상태에서는 $NO_x$와 CO가 각각 2 ppm과 200 ppm의 배출농도를 나타내었고, 이는 정격 조건에 비해 투입열량이 적어져 연소온도의 저하로 인하여 열적 반응에 의해 생성되는 $NO_x$는 줄고, CO는 증가함을 알 수 있었다. 미국 EPA의 배출계수를 비교하기 위하여 투입된 연료의 열량을 기준으로 비교해 볼 때 본 연구의 결과가 $NO_x$의 경우 근사한 값을 보여 주었고, 이는 국내 바이오 가스 연소시의 오염배출계수로 잘 적용 가능함을 보여 주었다. 본 연구에서 사용한 가스엔진이 오염배출 측면에서 대기 환경보전법상의 배출 허용기준 내에서 가동됨을 알 수 있었고, 가동조건에 따라 연소온도를 증가시킴으로서 CO의 발생을 저감시킬 수 있으리라 사료된다.

• 한국대기환경학회지
• /
• 제29권6호
• /
• pp.745-756
• /
• 2013

The purpose of this study is to evaluate representativeness of fuel-based emission factors. Twelve light-duty diesel vehicles which meet Euro-3 to 5 legislative emission limits were selected for emission tests. Second-by-second modal emission rates of vehicles were measured on a standard laboratory chassis dynamometer system. An off-cycle driving cycle was developed as a representative Korean real-world on-road driving cycle. Fuel-based emission factors were developed for short trip segments that involved in the selected driving cycle. Each segment was defined to have unit travel distance, which is 1 km, and characterized by its average speed and Relative Positive Acceleration (RPA). Fuel-based $NO_x$ emission factors demonstrate relatively good representativeness in terms of vehicle operation conditions. $NO_x$ emission factors are estimated to be within ${\pm}20%$ of area-wide emission factor under more than 40% of total driving situations. This result implies that the fuel-based $NO_x$ emission factor could be practically implemented into the on-road emission management strategies, such as a remote sensing device (RSD). High emitting vehicles as well as high emitting operating conditions heavily affect on the mean values and distributions of CO and THC emission factors. Few high emitting conditions are pulling up the mean value and biasing the distributions, which weaken representativeness of fuel-based CO and THC emission factors.

• Environmental Engineering Research
• /
• 제23권3호
• /
• pp.242-249
• /
• 2018

The use of palm oil and diesel blended with ethanol, known as a microemulsion biofuel, is gaining attention as an attractive renewable fuel for engines that may serve as a replacement for fossil-based fuels. The microemulsion biofuels can be formulated from the mixture of palm oil and diesel as the oil phase; ethanol as the polar phase; methyl oleate as the surfactant; alkanols as the cosurfactants. This study investigates the influence of the three cosurfactants on fuel consumption and exhaust gas emissions in a direct-injection (DI) diesel engine. The microemulsion biofuels along with neat diesel fuel, palm oil-diesel blends, and biodiesel-diesel blends were tested in a DI diesel engine at two engine loads without engine modification. The formulated microemulsion biofuels increased fuel consumption and gradually reduced the nitrogen oxides ($NO_x$) emissions and exhaust gas temperature; however, there was no significant difference in their carbon monoxide (CO) emissions when compared to those of diesel. Varying the carbon chain length of the cosurfactant demonstrated that the octanol-microemulsion fuel emitted lower CO and $NO_x$ emissions than the butanol- and decanol-microemulsion fuels. Thus, the microemulsion biofuels demonstrated competitive advantages as potential fuels for diesel engines because they reduced exhaust emissions.

• 한국대기환경학회지
• /
• 제33권4호
• /
• pp.351-360
• /
• 2017

In this study, we developed emission factors from solid-fuel fired combustors. In order to increase the reliability of emission factors, we conducted a joint research with the Institute of Health and Environment. As a result, PM average concentration was $8.19mg/m^3$. $SO_2$ and $NO_x$ were respectively 8.46 ppm, 50.64 ppm. Hazardous air pollutants such as Cr, Pb and Hg were detected in trace amounts continuously for 2 years in some solid-fuel fired combustors. The emission factors for the three kinds of PM, $SO_x$, $NO_x$ were developed based on the measurement data. For the PM emission factors, that of SRF was 15.93 g/kg and that of Bio-SRF was 14.18 g/kg. Compared with those of US. EPA, emission factors of this study showed the results of low values. $SO_x$ emission factors were 4.42 g/kg for SRF and 1.39 g/kg for Bio-SRF. $NO_x$ emission factors were 13.21 g/kg and 4.43 g/kg, respectively. Through the results of this study, we would support atmospheric administration policies such as the emission factor notification revision.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권4호
• /
• pp.379-387
• /
• 2011

최근 디젤엔진에서 엔진성능향상 및 배출가스저감을 위해 저압 EGR시스템에 대하여 연구개발이 활발히 진행되고 있다. 저압 EGR시스템은 EGR율에 따라 과급압력이 영향을 받지 않기 때문에 PM을 최소 화하면서 $NO_x$를 저감할 수 있는 장점을 갖고 있다. 본 연구에서는 2.0L급 고속직분사방식의 엔진에서 출력 및 연비저하로 EGR적용이 어려운 엔진회전수 2000 rpm, BMEP 1.0 MPa, 과급압력 181.3 kPa인 중부하 운전영역에서 서로 다른 EGR시스템에 따른 엔진성능 및 배출가스 특성을 실험적으로 연구하였다. 그 결과로서 기존의 고압 EGR시스템 또는 배압조절밸브를 사용하는 저압 EGR시스템에 비하여 ETC를 적용한 저압 EGR시스템이 $NO_x$ 배출특성은 큰 차이가 없는 반면에, 연비 및 열효율이 향상되고 PM 저감에 연소효과를 나타내고 있음을 확인하였다.

• Journal of Mechanical Science and Technology
• /
• 제15권10호
• /
• pp.1442-1450
• /
• 2001

The EGR system has been widely used to reduce nitrogen oxides (NO$\_$x/) emission, to improve fuel economy and suppress knock by using the characteristics of charge dilution. However, as the EGR rate at a given engine operating condition increases, the combustion instability increases. The combustion instability increases cyclic variations resulting in the deterioration of engine performance and emissions. Therefore, the optimum EGR rate should be carefully determined in order to obtain the better engine performance and emissions. An experimental study has been performed to investigate the effects of EGR on combustion stability, engine performance,70x and the other exhaust emissions from 1.5 liter gasoline engine. Operating conditions are selected from the test result of the high speed and high acceleration region of SFTP mode which generates more NO$\_$x/ and needs higher engine speed compared to FTP-75 (Federal Test Procedure) mode. Engine power, fuel consumption and exhaust emissions are measured with various EGR rate. Combustion stability is analyzed by examining the variation of indicated mean effective pressure (COV$\_$imep/) and the timings of maximum pressure (P$\_$max/) location using pressure sensor. Engine performance is analyzed by investigating engine power and maximum cylinder pressure and brake specific fuel consumption (BSFC)

• 한국수소및신에너지학회논문집
• /
• 제34권1호
• /
• pp.69-76
• /
• 2023

An experimental study was conducted on a 4-stroke direct injection diesel engine to examine the combustion and emission characteristics of 1-octanol/diesel fuel blends. The concentration of 1-octanol in the fuel blends was 10%, 30%, and 50% by volume. Experiments were conducted by varying the engine torque from 6 Nm to 12 Nm at the same engine speed of 2,700 rpm. Results showed that the fuel conversion efficiency increased as the 1-octanol proportion increased under most experimental conditions. However, the brake specific fuel consumption increased due to the relatively low lower heating value of 1-octanol. The smoke opacity and the concentrations of NO_x and CO emissions generally decreased with brake mean effective pressure as the 1-octanol proportion increased. On the other hand, the unburned hydrocarbon concentration increased with an ascending ratio of 1-octanol.

• 대한기계학회논문집B
• /
• 제31권5호
• /
• pp.405-415
• /
• 2007

The effects of recirculated exhaust gas on exhaust emissions under four kinds of nozzle tip with the different fuel consumption rates are experimentally investigated by using an once-through boiler with a FGR system. The purpose of this study is to develop the FGR control system for reducing $NO_x$ emissions in boilers. Intake and exhaust oxygen concentrations, and equivalence ratio are considered to figure out the effect of FGR rate on exhaust emissions at various fuel consumption rates. It is found that $NO_x$ emissions are markedly decreased, while soot emissions are increased owing to the drop of intake and exhaust oxygen concentrations, and the rise of equivalence ratio as FGR rates are elevated. One can also conclude that the reduction in $NO_x$ emissions is more considerably influenced by the variation of equivalence ratio due to the FGR rate than the fuel consumption rate.

• 대한기계학회논문집B
• /
• 제30권9호
• /
• pp.842-849
• /
• 2006

An experimental study has been conducted to investigate the effects of a multi air-staged burner on NOx formation and heat transfer in a 15kW large-scale laboratory furnace adopted the reburning process. The reburn fuel as well as burnout air was injected from each nozzle attached at the wall of the cylindrical furnace. Fuel in both main burner and reburn nozzle was LPG (Liquefied Petroleum Gas). The paper reports the influences on NOx reduction of reburn fuel fraction in reburning zone. Temperature distribution inside the overall region as well as total heat flux at the wall of the furnace has been measured to examine the heat transfer characteristics due to the reburning process. For comparison, the reburning effects were examined for a combustor with two types of burner; a regular single staged burner and a multi-air staged burner. A gas analysis was also performed to evaluate an appropriate condition for NOx emission in a primary zone for the excess air ratio of 1.1. As a result, combustion efficiency expected to become more efficient due to the reduction of heat loss in burnout zone decrease when multi air-staged burner in furnace adopted reburning technology was used.

• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.166-173
• /
• 2006

This study investigates a heavy duty diesel engine with swept vol. 12.6L, 4cycle-OHC type to verify the effects of the performance and exhaust gas emission according to the variable specifications of both swirl ratio and flow coefficient in inlet port, combustion bowl and fuel injection system. To meet the high BMEP and stringent exhaust emission standard, a turbocharger with wastegate and an intercooler were installed in the engine. Helical port, major design parameters for combustion chamber and electronic fuel injection pump with 1,000bar were reviewed and applied. Confirmation tests were also performed to meet the target value, $NO_x$ 5.0g/kWh and PM 0.1g/kWh of Euro3 exhaust emission legislation. The results of this study show that not only is it effective to use a relatively bigger bowl size for controlling rapid burning condition due to the decreased in-bowl swirl, but also to use a concave cam with double injection rates to decrease $NO_x$.