• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.2
• /
• pp.74-81
• /
• 2012

The purpose of this study provides the theoretical model for protecting the economic and social loss from the current alternative fuel vehicle which is developed without compatibility and senseless one's own through verifying the statistical significant by method of measuring analysis. The market scale of alternative fuel vehicle depends on customer's and station's expectation about the number of potential vehicle users. It is very difficult for vehicle manufacturer to make a decision on the standard alternative fuel vehicle as it might reduce profit and market share. Accordingly, the development of alternative fuel vehicle should have manufacturer confident on the potential profit in the future. Moreover, if we decide to use the non-standard fuel after we started to use the standard fuel, it would take a huge cost comparing with starting to use the standard fuel only. As a result, once one of companies starts to provide the non-standard fuel service, it is getting more difficult to use the standard fuel going forward. Consequently, we may review the possibility of choice on the standard fuel before the vehicle manufacturer starts service with non-standard fuel.

• Journal of ILASS-Korea
• /
• v.4 no.4
• /
• pp.9-16
• /
• 1999

Spray angle, a parameter which is most commonly used to evaluate. spray distribution, is important because it affects the axial and radial distribution of the fuel. Spray angles were measured and compared for the pintle-type gasoline fuel injector with n-heptane as a test fuel with the three different measuring techniques, i.e. digital image processing, shadowgraphy and spray patternator, respectively. Fuel was injected with the injection pressures of 0.2-0.35MPa into the room temperature and atmospheric pressure environment. In digital image processing method, the transmittance level greatly influences the spray angle with the axial distance from the injector. From the experimental results by the shadowgraphy technique, it is obvious that the spray angle vary during the injection period. The results of spray angle from the spray patternator show that there exist the different spray angles in the different areas. The spray angles increase with the increase in the injection pressure for the three measurement techniques considered in this study. The spray angle is widely different, especially in the near region from the injector, according to the measurement techniques used in this experimental work.

• Journal of ILASS-Korea
• /
• v.4 no.2
• /
• pp.19-32
• /
• 1999

The present study investigated the forms and behaviors of fuel during intake and compression process, and the initial flame stability in a lean burn engine modified as a single cylinder engine equipped with quartz windows for visualization. PLIF(Planar Laser Induced Fluorescence) method with KrF Excimer laser was used for measuring the fuel distributions. The principal design concept of the lean burn nin in this study is the axial stratification in the fuel distribution via fuel injection during intake process and different shapes of intake ports; helical and straight. The experiments showed that fuel flowed in as a vapor state in the early part of intake process and lots of this mixture mated down along the intake valve side cylinder wall, but in the latter part, a lot of fuel flowed in as a liquid state and this fuel stayed in the upper part of cylinder, after that the dense fuel cloud moved upward in the early of part compression process. It became clear that the fuel flowed in via straight port had a important role in the axial fuel stratification.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.118-130
• /
• 1995

Fuel spray in a gasoline engine is a significant factor for the decision of engine power, pollutant emission and the design of intake manifold system. Three kinds of fuel which has other physical properties are chosen in this study, and it is observed using an image processing method that the mechanism and structure of free fuel spray with a throttle type gasoline injector, and the detailed characteristics of droplet size and velocity distributions are obtained by macro and micro-scopic measuring method respectively. It is verified that the initial breakup behaviors are depended on We like the result of Reitz's study, and also observed that the spray of octane and solvent with Re of 210~330 and 270~330 respectively are better than ethanol which has relatively high density and viscosity.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.6
• /
• pp.121-126
• /
• 2001

Currently, potentiometric method has been employed to measure fuel amount for automobile. However, potentiometer could be malfunctioned or damaged due to the additives or dirt in fuel because a variable electric resistor is immersed in fuel. Therefore, a device employing strain sensor is designed and tested to verify the possibility as an alternative of the conventional fuel sender. Existing fuel tank has irregular cross section. Therefore, buoyancy is not increased linearly as fuel amount is increased. We design a floater that can compensate the irregular cross section of fuel tank and make buoyancy to increase linearly with increasing fuel amount. New fuel sender, comprising of strain gages on circular membrane, the above commented floater and the cover to prevent the disturbance due to sudden acceleration and deceleration, is designed and tested to replace current fuel sender. On the other hand, we are developing strain sensor that has strain gage deposited directly on the circular membrane with cantilever beam.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.55-62
• /
• 2009

As an experiment investigation, the effects of ethanol blended gasoline fuel with different injection method on nano-sized particle emission characteristics were examined in a 0.5L spark-ignited single-cylinder engine with a compression ratio of 10. Because this engine nano-particles are currently attracting interest due to its adverse health effects and their impact on the environments. So a pure gasoline and an ethanol blended gasoline fuels, namely E85 fuel, used for this study. And, as a particle measuring instrument, a fast-response particle spectrometer (DMS 500) with heated sample line was used for continuous measurement of the particle size and number distribution in the size range of 5 to 1000nm (aerodynamic diameter). As this research results, we found that the effect of ethanol blending gasoline caused drastic decrease of nano-particle emissions when port fuel injection was used for making better air-fuel mixture than direct fuel injection. Also injection timing, specially direct fuel injection, could be a dominant factor in controlling the exhaust particle emissions.

• Nuclear Engineering and Technology
• /
• v.53 no.3
• /
• pp.1041-1048
• /
• 2021

An engineered barrier system (EBS) for the disposal of high-level radioactive waste (HLW) is composed of a disposal canister with spent fuel, a buffer material, a gap-filling material, and a backfill material. As the buffer is located in the empty space between the disposal canisters and the surrounding rock mass, it prevents the inflow of groundwater and retards the spill of radionuclides from the disposal canister. Due to the fact that the buffer gradually becomes saturated over a long time period, it is especially important to investigate its thermal-hydro-mechanical-chemical (THMC) properties considering variations of saturated condition. Therefore, this paper suggests a new method of measuring thermal conductivity and water suction for single compacted bentonite at various levels of saturation. This paper also highlights a convenient method of saturating compacted bentonite. The proposed method was verified with a previous method by comparing thermal conductivity and water suction with respect to water content. The relative error between the thermal conductivity and water suction values obtained through the proposed method and the previous method was determined as within 5% for compacted bentonite with a given water content.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.2
• /
• pp.79-84
• /
• 1999

An image processing technology was developed to measure the dimension of nuclear fuel rods and the diameter of nuclear fuel rods was measured by this method. It was confirmed that parameters such as camera-to-specimen distance. camera location, light intensity and light characteristic would affect dimension measurement of nuclear fuel rods. The percent relative error and percent standard deviation of measuring the diameter of nuclear fuel rods using image processing method were 4.88%, ${\pm}3.34%$ while the percent relative error and percent standard deviation using conventional method were 12.7%, ${\pm}9.72%$, respectively. The accuracy of diameter measurement of nuclear fuel rods using image processing method was about 3 times as high as that using conventional method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.6
• /
• pp.579-582
• /
• 2012

Removing residual water in a fuel cell is a critical operational process for managing its performance and controlling its lifetime. Understanding the mechanism of water transport in fuel cells is essential for the design of the water removal process. In this study, an experimental method for measuring the water evaporation rate through a gas diffusion layer, which is a porous medium, under steady-state conditions was developed. Experimental bench tests were conducted to apply the developed method. Then, the effects of various parameters of the drying gas and the gas diffusion layer were experimentally measured. The water evaporation rate increased as the humidity of the drying gas decreased and the flow rate of the drying gas increased. In addition, a thinner gas diffusion layer yielded a higher water evaporation rate.

• Nuclear Engineering and Technology
• /
• v.8 no.2
• /
• pp.81-88
• /
• 1976

A flash method for measuring the unknown thermal property (the density, specific heat, or thermal diffusivity could be chosen as unknown) is described. The thermal diffusivity of UO$_2$ fuel samples is obtained from room temperature (300 K) to high temperature (1400 K). The specific heat is measured using a commercially available differential scanning calorimeter from room temperature to 500 K. The thermal conductivity of UO$_2$ fuel samples is calculated from the density, thermal diffusivity, and specific heat at constant pressure. The present results are in complete agreement with the usual trends for the thermal conductivity of dielectric materials, in which impurity levels are very important at low temperatures but become relatively unimportant at high temperatures. In addition, the thermal diffusivity values at room temperature are reexamined by measuring the thermal diffusivity of several UO$_2$ fuel samples with same level of doped Gd$_2$O$_3$.