• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.8-15
• /
• 2003

During cold operation, fuel injection in the intake port directly contributes to the unburned hydrocarbon formation in spark ignition engines. The relationship between injection parameters and HC emission behavior was investigated through a series of experiments. Spray behavior of port fuel injectors was characterized through a quantitative evaluation of mass concentration of liquid fuel by a patternator and PDA(Phase-Doppler. Anemometer). A 6-hole injector was found to produce finer spray than single hole injector. Using a purpose-built wall, the wetted fuel was measured, which was mostly affected by wall temperature. HC emissions were measured in a production engine varying coolant temperature$(20~80^{\circ}C)$, also with respect to the different types of injectors. In the 6-hole injector application, the engine produced less HC emission in low coolant temperature region. Though it produces much more amount of wetting fuel, it has the advantages of finer atomization quality. In high coolant temperature region, there was little effect by different types of injectors. The control schemes to reduce HC emissions during cold start could be suggested from the findings that the amount of fuel supply and HC emission could be reduced by utilizing fine spray and high intake wall temperature.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.138-143
• /
• 2006

Modification of injector, oil ring tension reduction and oil pump rotor re-matching with optimization of relevant engine control parameters could drive fuel consumption reduction of HSDI diesel engine. A 5 holes injector was replaced with a 6 holes with smaller nozzle hole diameter and 1.5 k factor, and evaluated in a view of fuel economy and emission trade-offs. With introducing smaller nozzle hole diameter injector, PM(Particulate Matter) was drastically decreased for low engine load and low engine rpm. Modification of oil pump and oil ring was to reduce mechanical friction and be proved to better fuel economy. Optimization of engine operating conditions was a great help for the low fuel consumption. Influence of the engine operating parameters· including pilot quantity, pilot interval, air mass and main injection timing on fuel economy, smoke and NOx has been evaluated with 14 points extracted from NEDC(New European Driving Cycle) cycle. The fuel consumption was proved to $7\%$ improvement on an engine bench and $3.7\%$ with a vehicle.

• Journal of the Korean Institute of Gas
• /
• v.17 no.3
• /
• pp.8-13
• /
• 2013

The purpose of this paper is to study for fire example by fuel leakage in LPG Vehicle. At first example, the car was repaired the fuel line that was connected with pressure hose between fuel regulator and injector in engine. But the service man was not very tighten with regular torque. At a result, the gas leaked on hot parts of engine. It verified the production of fire by engine heat. At second example, when the repair man, after replacement the injector, inserted the injector in a assembling part of it, he didn't the transform condition of fixing part. Therefore, the tearing phenomenon of O ring producted the controlled leakage of fuel by the injector deflection. It found the fact that the fuel leaked with gap of O ring. At third example. the fuel-cut solenoid valve was lined with pressure regulator unit. But the service man didn't throughly certify the leaked work of connected parts after repaired it. As a result, it certified the fire by engine heating leaked liquefied petroleum gas. Therefore it have to minimize the fire production that the driver should do no problem to throughly manage the fuel system.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.239-243
• /
• 2008

Fluid flow in LPG injector is delayed momently around nozzle and leaked accidentally, then engine operation becomes unstable. When attached cutsole injector that we can prevent fuel from leaking. Attaching additional devices cause loss of power and pressure. In this study, We has analyzed the performance of the LPG injector nozzle by changing cutsole geometry numerously by using Computational Fluid Dynamics.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.239-243
• /
• 2008

Fluid flow in LPG injector is delayed momently around nozzle and leaked accidentally, then engine operation becomes unstable. When attached cutsole injector that we can prevent fuel from leaking. Attaching additional devices cause loss of power and pressure. In this study, We has analyzed the performance of the LPG injector nozzle by changing cutsole geometry numerously by using Computational Fluid Dynamics.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.2
• /
• pp.83-89
• /
• 2009

An air-fuel ratio control is essential in reducing hazardous exhaust emissions from a compressed natural gas(CNG) engine, and can be accomplished by accurate control of gas injection flow. In this study, theoretical research was conducted on injection characteristics of a solenoid gas injector, and injection experiments for calibration and analysis were performed. Various factors for gas injection flow such as injection pressure, gas temperature, and supply voltage are studied. A dynamic flow equation of the natural gas was proposed on the basis of flow dynamics theories and results of the injection experiment. The verification of the dynamic flow equation of the solenoid injector was carried out with a large CNG-engine applied to an urban bus. Air-fuel ratio control experiments were conducted in both steady and transient state. Results of injection experiments for the solenoid injector and the CNG-engine was proved the control method proposed herein to be effective.

• Journal of ILASS-Korea
• /
• v.17 no.2
• /
• pp.57-63
• /
• 2012

For reduction of CO, NOx and soot emission emitted by diesel diffusion combustion, the authors focused on injection actuator to improve fuel availability inside combustion chamber. In this study, it was investigated the internal dynamic characteristics of two-stage injection with diesel injectors with different driving type for the common rail direct injection by using the AMESim simulation code. The analysis parameter defined such as fuel pressure, injection hole's diameter and driven voltage. As the results, it was shown that the piezo-driven injector had a faster response and had better control capability than the solenoid-driven injector. It was found the piezo-driven injector can be utilized effectively as multiple injector than solenoid-driven injector.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.10-17
• /
• 2000

This work presents an investigation of aerodynamic characteristics of fuel spray injected from a high pressure hollow cone swirl injector into a constant volume chamber. Laser tomography visualization was used to interrogate the fuel and air mixing characteristics and the effect of chamber pressure and temperature increase was analyzed, Preliminary results on spray development showed that mixing effect tends to increase with the increase of injection pressure and chamber gas pressure yielding a decrease of spray penetration and an attenuation of well-defined vortex structure. Topological analysis of the spray structure has been performed to initiate the understanding of mixing and vaporization process. For the present experimental conditions fuel injection pressure and chamber gas pressure appear as the dominant factors which govern the transient mixing characteristics. Moreover spray atmixation characteristics are improved by increasing chamber gas temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.9
• /
• pp.722-727
• /
• 2009

The effect of the intake flow on the spray structure of a high pressure 11-hole fuel injector were examined in a single cylinder optical direct injection spark ignition (DISI) engine. The effects of injection timing and in-cylinder charge motion were investigated using the 2-dimensional Mie scattering technique. It was confirmed that in the homogeneous charge mode, the in-cylinder swirl charge motion played a major role in the fuel spray distribution during the induction stroke rather than the tumble flow. But, in the stratified charge mode, the effect of the in-cylinder charge was not so large that the injected spray pattern was nearly maintained and the increase of in-cylinder pressure by the upward moving piston reduced the fuel spray penetration.

• Journal of ILASS-Korea
• /
• v.3 no.3
• /
• pp.42-48
• /
• 1998

This study describes the spray structure of gasoline port injectors by using phase Doppler particle analyzer(PDPA) and particle motion analysis system(PMAS). The characteristics of fuel spray such as the spray penetration, spray angle and breakup processes were obtained by PMAS and the droplet size and mean velocity were measured by PDPA system. Pintle type and two-hole type injectors were used as gasoline port fuel injectors under various injection pressures. The effect of injection pressure on the droplet mean diameter and axial mean velocity of droplet were investigated under the various injection conditions. In addition the comparison of breakup processes for the two types of injectors was also conducted. It Is shown that pintle type injector has smaller droplet size than that of two-hole type injector.