• 대한기계학회논문집B
• /
• 제24권4호
• /
• pp.512-518
• /
• 2000

A wall fuel-film flow model is developed to predict the effect of a wall-fuel-film on air-fuel ratio in an SI engine in transient conditions. Fuel redistribution in the intake port resulting from charge backflow and a simple liquid fuel behavior in the cylinder are included in this model. Liquid fuel film flow is calculated of every crank angle degree using the instantaneous air flow rate. The model is validated by comparing the calculated results and corresponding engine experiment results of a commercial 4 cylinder DOHC engine. The predicted results match well with the experimental results. To maintain the constant air-fuel ratio during transient operation. the fuel injection rate control can be obtained from the simulation result.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4329-4337
• /
• 2022

Jet impinging device is designed for decay heat removal on horizontal fuel rods in a low temperature heating reactor. An experimental system with a fuel rod simulator is established and experiments are performed to evaluate water film covering capacity, within 0.0287-0.0444 kg/ms mass flow rate, 0-164.1 kW/m² heating flux and 13.8-91.4℃ feeding water temperature. An effective method to obtain the film coverage rate by infrared equipment is proposed. Water film flowing patterns are recoded and the film coverage rates at different circumference angles are measured. It is found the film coverage rate decreases with heating flux during single-phase convection, while increases after onset of nucleate boiling. Besides, film coverage rate is found affected by Marangoni effect and film accelerating effect, and surface wetting is significantly facilitated by bubble behavior. Based on the observed phenomenon and physical mechanism, dry-out depth and initial dry-out rate are proposed to evaluate film covering potential on a heating surface. A model to predict film coverage rate is proposed based on the data. The findings would have reliable guide and important implications for further evaluation and design of decay heat removal system of new reactors, and could be helpful for passive containment cooling research.

• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.77-84
• /
• 1994

The oil crises in 1973 and 1978 stimulated the alternative fuel research activities in many countries around the world. Among the alternative fuels, methanol is one of the highest potential fuels for transportation. Methanol has been considered for use as automotive fuel, but it has a defect of the great latent vaporization heat. Therefore, authors have made the fuel vaporizing device in order to eliminate the fuel film flow heating the mixture. This paper presents a study on the characteristics of vaporization, engine performance, and emission which result from using the fuel vaporizing device.

• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.167-173
• /
• 2003

An experimental study on the behavior of droplets impinging on a solid flat surface was carried out in the present study. Breakup of a liquid droplet impinging on a solid surface has been investigated experimentally for various fuels with different properties. The fuel temperature and incident angle were chosen as major parameters. And fuel temperature and incident angle varied in the range from $-20^{\circ}C$ to $30^{\circ}C$ and from $30^{\circ}$ to $60^{\circ}$, respectively, were investigated. It was found that the variation of fuel temperature influences upon droplet mean diameter which were bounced out from the solid surface. As the increases of incident angle, the break-out mass flow rate increases. This causes the decrease of liquid film flow rate. The larger incident angle gives less liquid film flow rate.

• 오토저널
• /
• 제5권3호
• /
• pp.33-44
• /
• 1983

This paper deals with the experimental study on the behavior of fuel (methanol) in intake manifold by using the basic apparatus which is manufactured the visible straight tube type model. In this study, the new device for liquid film thickness measurement and vaporization rate measurement are introduced to investigate the variation of liquid film thickness along the intake manifold and to observe the effect of vaporization of injected fuel. the results are summarized as follows: 1) The vaporization rate increases in proportion to decreasing of throttle valve angle and growing air fuel ratio. 2) The liquid film thickness along the intake manifold is mostly independent for the throttle valve angle in low air velocity and then affected in high air velocity, but the distribution of the liquid film thickness on circumferential position almost constant in the region of 300mm down stream from carburetor. 3) The mean liquid film thickness is 0.04 - 0.18mm in case of methanol in the region of air velocity Va = 12m/s - 55m/s and decreases with decreasing the throttle valve angle.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.15-22
• /
• 2002

As the emission regulations on the automobiles have been increasingly stringent, precise control of air/fuel ration is one of the most important issues on the gasoline engines. Although many researches have been carried out to identify the fuel transport phenomena in the port fuel injection gasolines, mixture preparation in the cylinder has not been fully understood due to the complexity of fuel film behavior, In this paper, the mixture preparation during cold engine start is studied by using a Fast Response Flame ionization Detector.(FRFID) In order to estimate the transportation of injected fuel from the intake port into cylinder, the wall wetting fuel model was used. The two coefficient($\alpha$,$\beta$) of the wall-wetting fuel model was determined from the measured fuel mass that was inducted into the cylinder at the first cycle after injection cut-in. $\alpha$( ratio of directly inducted fuel mass into cylinder from injected fuel mass) and $\beta$ (ratio of indirectly inducted fuel mass into cylinder from wall wetted fuel film on the wall) was increased with increasing cooling water temperature. To reduce a air/fuel ratio fluctuation during cold engine start, the appropriate fuel injection rate was obtained from the wall wetting fuel model. Result of air/fuel ratio control, air/fuel excursion was reduced.

• 대한기계학회논문집
• /
• 제16권9호
• /
• pp.1736-1743
• /
• 1992

본 연구에서는 기화기부착 4행정 4기통 전기점화기관을 사용하여 흡기관내 액 막흐름에 의한 연료의 불균일화가 기관의 연소특성과 배기특성에 미치는 영향을 규명 하는데 궁극적인 목적을 두고 우선, 연소특성을 해석하기 위하여 비교적 고가인 연소 해석 시스템을 개발하는데 1차적인 목적으로 하였으며, 시험제작한 연소해석 시스템으 로 액막흐름의 가시화 및 배기가스 농도측정과 지압선도 해석을 행하여 구조적으로 대 칭인 1번과 4번 실린더의 연소특성과 배기특성을 비교 검토하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.135-140
• /
• 2007

막냉각이 적용된 액체로켓엔진의 비추력 최적조건을 분석하였다. 본 연구에서 구한 엔진의 비추력 성능을 문헌에 소개된 가스발생기 사이클 엔진의 개념설계와 비교하여 적절한 정확성을 가지는 것을 확인하였다. 비추력을 극대화할 수 있는 조건으로 최적의 막냉각 유량과 재생냉각 용량의 조합이 제시되었다. 추력이 증가될 경우, 막냉각 유량이 감소하고 연료펌프 차압은 증가한다. 터빈 입구온도 증가에 따라 최적 조건의 막냉각 유량과 연료펌프 차압이 증가한다. 코킹 온도 증가 역시 터빈 입구온도와 정성적으로 동일한 영향을 가진다.

• 한국추진공학회지
• /
• 제9권4호
• /
• pp.48-54
• /
• 2005

액체 산소(LOx)와 Jet A-1(Jet engine fuel)을 추진제로 하는 소형 액체 로켓 연소기에서 막 냉각의 효과에 관한 실험적 연구를 수행하였다. 막 냉각제(Jet A-1과 물)는 막냉각장치를 통해 분사되도록 하였다. 막 냉각 유량 변화에 따른 연소기의 외벽온도 및 막 냉각 길이는 추진제 혼합비, 연소실 압력 및 막냉각장치의 형상 변화(분사각)에 따라 비교하였다. 막 냉각에 따른 특성속도 효율의 손실도 막 냉각제를 물과 Jet A-1을 사용하였을 경우에 대해서 각각 구하였다. 연소실 압력의 증가에 따라 노즐에서의 외벽 온도는 증가하였으나, 퍼센트 막냉각 유량이 9% 이상인 경우에 연소실에서는 거의 영향을 받지 않았다. 특성속도는 퍼센트 막냉각 유량이 9% 이상일 때 추진제 혼합비에 영향을 받지 않았다.

• 한국수소및신에너지학회논문집
• /
• 제32권5호
• /
• pp.340-346
• /
• 2021

The initial electrochemical performance of ceramic fuel cell with thin-film electrolyte fabricated by plasma-enhanced atomic layer deposition method was evaluated in terms of peak power density ratio, open circuit voltage ratio, and activation/ohmic resistance ratios at 500℃. Hydrogen and air were used as anode fuel and cathode fuel, respectively. The peak power density ratio reduced as ~52% for 30 min, which continually decreased as time increased but degradation rate gradually decreased. The open circuit voltage ratio decreased with respect time; however, its behavior was evidently different from the reduction behavior of the peak power density. The activation resistance ratio increased as ~127% for 30 min, which was almost similar with the reduction behavior of the peak power density ratio.