• 한국가스학회지
• /
• 제21권2호
• /
• pp.20-25
• /
• 2017

압축 천연가스에 수소를 혼합한 HCNG 연료를 사용하는 HCNG 버스에 대해 WHVC 차량시험 결과를 토대로 연료 경제성 및 $CO_2$ 배출특성을 분석하였다. 동급 CNG 버스 및 디젤버스 시험결과와 비교하여 HCNG 버스의 연비 개선효과와 $CO_2$ 저감효과를 고찰하였다. $CO_2$ 배출특성은 탄소배출계수에 따른 연료효과와 연비에 의한 효과로 분석하였다. 분석결과 HCNG 버스는 CNG 버스 보다 연비는 11.5% 개선되었고 디젤버스와는 동등수준을 보이는 것으로 나타났다. 또한 $CO_2$ 배출 특성으로 HCNG 버스는 CNG 버스에 비해 20.4% 개선효과가 있고 디젤버스에 비해 34.5% 향상되는 것으로 분석되었다. 이산화탄소 배출특성은 연료성분에 따른 탄소배출계수와 엔진성능에 따른 연비에 영향을 받는 것으로 귀결되었다.

• 오토저널
• /
• 제6권4호
• /
• pp.36-45
• /
• 1984

The relationship between vehicle driving pattern and fuel consumption in urban area was studied in Seoul along three representative routes using a test car equipped with all the instruments required for recording modes of traffic and measuring fuel consumption. Correlation with idle speed, fuel consumption and CO concentration of car in use was also measured. The average vehicle speed in Seoul was 31.4 km/h and the time spent in different modes was 23.0% in idle mode, 22.5% in acceleration mode, 32.4% in cruising mode and 22.3% in deceleration mode, respectively. Hence, traffic flow was suggested to be relatively smooth. Fuel consumption per unit distance, .phi. was closely related with trip time spent per unit distance, t, and correlation coefficient obtained from the test car was 0.925, and the relationship between .phi. and t was also obtained from the linear regression with the following equation. .phi.=42.87+0.38 t. Idle speed of vehicle in use was mostly adjusted low and cars which were over the permissible standard of CO concentration (4.5%) were 50% or more. As the idle speed decreased, the fuel consumption was decreased, while the CO concentration was increased. Therefore, the decrease of fuel consumption can not be expected with only a decrease in idle speed.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.41-42
• /
• 2006

A study on the combustion characteristics by using Emulsion Fuel in Diesel Engine is performed experimentally. In this paper, the experiments are performed at engine speed 1800rpm, emulsion fuel ratio is 0%, 10%, 20%, and main measured items are specific fuel consumption, pressure, ratio of pressure rise, rate of heat release etc. The obtained conclusions are as follows. 1) Specific fuel consumption increase maximum 19.8% at low load, but is not effected at full load. 2) Ratio of pressure rise and rate of heat release are about the same in the case of 10% and 20% of emulsion fuel ratio. 3) Cylinder Pressure increase 11.7%, ratio of pressure rise increase 60.4% in case of emulsion fuel ratio 20% at full load. 4) Rate of heat release increase 76.9% in case of emulsion fuel ratio 20% at full load.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권3호
• /
• pp.516-521
• /
• 2004

In this paper, the effects of ethanol blended gasoline on emissions and their catalytic conversion efficiencies characteristics were investigated in gasoline engine with an electronic fuel injection. The results showed that the increase of ethanol concentration in the blended fuels brought the reduction of THC and $CO_2$ emissions from the gasoline engine. THC emissions were drastically reduced up to thirty percent. And brake specific fuel consumption was increased. but brake specific energy consumption was similar level. However. unburned ethanol and acetaldehyde emissions increased. The conversion efficiency of Pt/Rh based three-way catalysts and the effect of ethanol on CO and NOx emissions were investigated by the change of engine speed. load and air/fuel ratio. Furthermore, the ethanol blended fuel results in the reduction effect of THC. CO and NOx emissions at idle speed.

• 오토저널
• /
• 제9권1호
• /
• pp.57-68
• /
• 1987

The driving pattern was studied in Seoul along nineteen representative routes using a test car equipped with all the instruments required for recording traffic flow and measuring fuel consumption. Speed histories, gear shift points, instantaneous fuel consumption rates, etc. were recorded and the data were anlyzed to determine the traffic characteristics for Seoul. The Seoul-14 Mode has been developed to simulated actual driving conditions in Seoul with respect to fuel consumption. The average speed of the Seoul-14 Mode is 30.1 Km/h and the Mode length is 11.94 Km.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.121-130
• /
• 2014

This paper is the second investigation on the effects of intake flow control methods on the part load performance in a spark ignition engine. In the previous work, two control methods, port throttling and masking, were compared with respect to lean misfire limit, fuel consumption and emissions. In this work, the effects of these two methods on EGR characteristics were studied and simultaneously the differences between EGR and lean combustion as a dilution method were investigated. The results show that EGR limit is expanded up to 23% and 3 ~ 5% improvement in the fuel consumption are achieved around 8 ~ 13% rates by the flow controls comparing with 10% limit and 1.5% reduction around 3% rate of non-control case. The masking method is more effective on the limit expansion than throttling as like as lean misfire limit; however there is no substantial difference in fuel consumptions improvement regardless the control methods except high load condition. Also it is observed that there exist critical EGR rates around which the combustion performance and NOx formation change remarkably and these rates generally coincide with optimum rates for the fuel consumption. In addition, dilution with fresh air is much more advantageous than that of the exhaust gas from the view point of dilution limit and fuel consumption, while utilization of the exhaust gas is more effective on NOx reduction in spite of considerably small dilution compared with the use of fresh air. Finally, the improvement of fuel consumption by massive EGR is highly dependent on the EGR limit at which the engine runs stably, therefore the stratified combustion technique might be a best solution for this purpose.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1091-1096
• /
• 2004

It is necessary to consider the stability, economic environmental-friendly problems by the development of the road, supply of the automobile, environmental problem as designing the exhaust system. To reduce the noise and the vibration of the automobile. The need for stricter regulation limits emission and demand for lower fuel comsumption. According to motor vehicle company develop variable type muffler, dual muffler and active intelligence exhaust system unit. Improvement in engine performance and fuel consumption for demand information of pressure fraction and heat characteristics. To be able to determine these factor for we experiment on each case of exhaust system unit. In this study, in order to establish the optimized conditions design factors which are taking many performance as the variable valve, it shows how the standard performance and the additional element of the exhaust system effects on the engine performance.

• Journal of Biosystems Engineering
• /
• 제34권3호
• /
• pp.135-139
• /
• 2009

Harmful exhaust emissions of diesel engines are recognized as main causes of air pollution in these days. But, the direct injection diesel engine is widely used for sake of minimization on energy consumption. Because biodiesel fuel is a renewable and alternative fuel for a diesel engine, its usability is expanded. To investigate the effect of biodiesel fuel(extracted from rapeseed oil) on the characteristics of performance and exhaust emissions in an agricultural diesel engine, the biodiesel fuel derived from rapeseed oil was applied in this study. Smoke emission of esterified rapeseed oil was reduced remarkably by approximately 44.5% at 1500 rpm, full load in comparison with the commercial diesel fuel. The power, torque and brake specific energy consumption of the diesel engine showed very slight differences. It was concluded that esterified rapeseed oil could be utilized effectively as an alternative and renewable fuel for agricultural direct injection diesel engines.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.1243-1248
• /
• 2008

$CO_2$ emission amount and characteristics of combined heat and power (CHP) plant in industrial complex of Korea is evaluated by using the fuel analysis method. Fuel analysis methods of several foreign countries and developed one which is developed considering the operation characteristics of the surveyed CHP plants are used. The operation data is surveyed for all of the CHP plants in industrial complex and is composed of fuel consumption amount, generation, sale and efficiency of heat and electricity, condensed steam enthalpy, and etc of the each CHP.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권7호
• /
• pp.1123-1130
• /
• 2004

Numerical simulations have been carried out to investigate the effect of nozzle hole geometry on the combustion characteristics of the large diesel engine. 6S90MC-C. Spray and combustion phenomena were examined numerically using FIRE code. Wane breakup and Zeldovich models were adopted to describe the atomization characteristics and NOx formation processes. Predictions on the cylinder peak pressure and NOx emission were first verified with the experimental data to confirm the reliability of numerical calculations. The comparison results showed good agreements within the range of 0.64% and 4.6% respectively. Finally, the effects of fuel spray angle and diameter on the engine performance were investigated numerically to find the optimum nozzle hole geometry considering fuel consumption, NOx emission and heat flux of the combustion chamber wall. It was concluded that the combustion gas recirculation in cylinder by changing fuel injection direction is an effective method to reduce NOx emission by about 10% with increasing fuel oil consumption, 1.4% in a large diesel engine.