• 한국산학기술학회논문지
• /
• 제17권3호
• /
• pp.270-275
• /
• 2016

본 연구에서는 디젤 연료 온도에 따른 실제 분사되는 연료량, 분사율 그리고 거시적 분무 발달 과정에 대한 특성을 파악하고자 하였다. 시험 결과 동일한 분사 시작 신호 및 분사 기간 신호를 입력하였음에도 불구하고, 연료 온도가 낮아짐에 따라 실제 연료 분사량이 감소하는 경향을 보였다. 분사율 측정 결과를 통해 연료 온도가 낮은 조건에서 실제 분사 시작 시점이 지연되며, 실제 분사가 유지되는 기간이 짧아지는 것을 확인하였으며, 이를 통해 실제 분사되는 연료량 저감에 대한 근거를 찾을 수 있었다. 거시적 분무 이미지 촬영 결과를 연료 온도 별 분무 도달 거리로 표현하여 비교 하였으며, 낮은 연료 온도 조건에서 분무 미립화 성능 악화로 인해 분무 도달 거리가 길어지는 것을 확인하였다. 저온 조건에서의 연소 개선을 위해 향후 시도할 선행 평가로서 피스톤 타켓팅 평가를 수행하였으며, 이른 시기에 분사되는 파일럿 연료가 크레비스 영역으로 유입되는 것을 확인하였으며, 이를 통해 파일럿 분사 방식 적용 시 연료량 분배 및 분사 시기 선정이 매우 중요한 인자가 됨을 파악하였다.

• 한국분무공학회지
• /
• 제12권3호
• /
• pp.166-171
• /
• 2007

Recently, many studies on HSDI diesel engines have been performed to reduce the fuel consumption and $CO_2$ emission. One of the prominent technique to reduce emission is a high pressure multiple injection. For this technique, the injection rate is a critical parameter in order to determine precise injection duration and timing for combustion control. Thus the purpose of this study was to investigate relationship between the injection rate and the time-signature of chamber pressure at different injection pressure conditions in a common rail direct injection type injector using the Zeuch method. Using the measured correlation constants, estimated fuel injection rates are presented at many different injection conditions.

• Journal of Mechanical Science and Technology
• /
• 제20권9호
• /
• pp.1436-1448
• /
• 2006

This paper describes the effects of injection rate shaping on the combustion, fuel consumption and emission of $NO_x$ and soot of a medium duty diesel engine. The focus is on the influence of four different injection rate shapes, square type 1, square type 2, boot and ramp, with a variation of maximum injection pressure and start of injection (SOI). The experiments were carried out on a 1 liter single cylinder research diesel engine equipped with an amplifier-piston common rail injection system, allowing the adjustment of the injection pressure during the injection event and thus injection rate as desired. Two strategies to maintain the injected fuel mass constant were followed. One where rate shaping is applied at constant injection duration with different peak injection pressure and one strategy where rate shaping is applied at a constant peak injection pressure, but with variable injection duration. Injection rate shaping was found to have a large effect on the premixed and diffusion combustion, a significant influence on $NO_x$ emissions and depending on the followed strategy, moderate or no influence on soot emission. Only small effects on indicated fuel consumption were found.

• 오토저널
• /
• 제14권5호
• /
• pp.54-60
• /
• 1992

This paper deals with the results of injection characteristics and the influence parameters upon the fuel injection performance of the inline injection system in a diesel engine. In this study, the characteristics of the injection rate, the injection pressure and the injection duration have been investigated by changing the injection parameters. The predicted results and injection performance are compared to the measured data from the injection test system.

• 한국분무공학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2017

Recently, Performance and fuel efficiency of gasoline engines have been improved by adopting direct injection (DI) system instead of port fuel injection (PFI) system. However, injecting gasoline fuel directly into the cylinder significantly reduces the time available for mixing and evaporation. Consequently, particulate matters(PM) emissions increase. Moreover, as the emission regulations are getting more stringent, not only the mass but also the total number of PM should be reduced to satisfy the Euro VI regulations. Increasing the fuel injection pressure is one of the methods to meet this challenge. In this study, the effects of increased fuel injection pressures on combustion and emission characteristics were experimentally examined at several part load conditions in a 1.6 liter commercial gasoline direct injection engine. The main combustion durations decreased about $2{\sim}3^{\circ}$ in crank angle base by increasing the fuel injection pressure due to enhanced air-fuel mixing characteristics. The exhaust emissions and number concentration distributions of PM with particle sizes were also compared. Due to enhanced combustion characteristics, THC emissions decreased, whereas NOx emissions increased. Also, the number concentrations of PM, larger than 10 nm, also significantly decreased.

• 대한기계학회논문집
• /
• 제10권3호
• /
• pp.367-375
• /
• 1986

본 연구에서는, 주분무의 착화지연기간에 미치는 보조연료 분사시기의 영향 및 공기유동을 연소장 내에 도입시켜 분무와 공기의 혼합을 적극적으로 촉진시킴에 따라 그 후의 연소과정이 어떤 영향을 받는가에 대해서 검토했다.또 소형고속 디이 젤기관에서는 분무의 연소기간을 최대한 단축 시키지 않으면 안되므로, 보조연료 분사 에 의해 그 단축목적이 어느 정도 달성될 수 있는 가능성을 제2보에서 시사한 바 있으 나 본 연구에서 더욱 상세히 검토했다.

• 한국분무공학회지
• /
• 제17권3호
• /
• pp.121-127
• /
• 2012

The study is to investigate the mixing stability, fuel properties, and macroscopic spray characteristics of diesel-gasoline blended fuels in a common-rail injection system of a diesel engine. The test fuels were mixed diesel with gasoline fuel, which were based volume fraction of gasoline from 0 to 100% in 20% intervals. In order to analyze the blended effect of gasoline to diesel fuel, the properties of test fuels such as density, viscosity, and surface tension were measured. In addition, the spray behavior characteristics were studied by investigating the spray tip penetration and spray angle using a spray images through a spray visualization system. It was revealed that the density, kinematic viscosity and surface tension of diesel-gasoline blending fuels were decreased with the increase of gasoline fuel. The injection quantity of test fuels were almost similar level at short energizing duration condition. On the other hand, the increase of energizing duration shows the decrease of injection quantity compared to short energizing duration. The test blending fuels have similar growth in Spray tip penetration and Spray cone angle.

• 한국연소학회지
• /
• 제22권3호
• /
• pp.23-28
• /
• 2017

The fuel and oxidizer mixing process in the shock tube driven section is simulated numerically. The boundary condition is set based on an shock tube experimental condition. The objective is to predict the gas mixing time for experiments. In the experiment, the amount of fuel to be injected is determined in advance. Then, according to duration of fuel injection, 5 cases with the same fuel mass but different fuel mass flow rate are simulated. After fuel is injected into the driven section, the fuel and air will be mixed with each other through convection and diffusion processes. The mixing time is predicted numerically for experiments.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.88-94
• /
• 2010

In this paper, the effect of the ultrasonic energy on the diesel engine's smoke reduction has been investigated for indirect injection diesel engine. The smoke concentration of the ultrasonically reformed diesel fuel was reduced remarkably in comparison with conventional diesel fuel. And in-cylinder pressure, heat release rate and mass fraction burned was improved but combustion duration was decreased. However, The combustion durations and the smoke concentrations of both diesel fuels were proportional to the increases of engine loads. Also, When the combustion duration has been increasing, the smoke emission has been augmenting in the shape of the exponential functions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권3호
• /
• pp.644-654
• /
• 2001

In this paper, an electronic control unit of the automobile engine for optimal fuel injection an spark timing control has been designed and developed. This system includes hardware and software for a precise control of fuel injection and ignition timing. Especially, the crank angle sensor provides two separate signals: One is the position signal (POS) which indicates 180 degree pulses per revolution, and the other is the reference signal (REF) that represents each cylinder individually. Consequently, the developed engine control system has been able to control fuel injection and ignition timing more quickly and accurately. Through the experiment, it has been found that the fuel injection duration and the position of MBT have been influenced by coolant temperature, air flow rate and engine speed.