• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.7 s.196
• /
• pp.120-125
• /
• 2007

Analysis of elders' behavioral characteristic during showering provides important fundamental data when developing an automatic showering system. We recorded showering behavior of 37 elders' at the front, back, left and right view using four CCTV cameras. The photographic data were analyzed by counting the frequencies of body scrub and identifying zones where hands could reach. And we measured their body sizes, and conducted questionnaire of showering for 302 peoples. Analysis was done according to the analysis criteria established. The human body was divided into 14 zones from a body, and the numbers of body scrub for each zone were counted. The average total numbers of body scrub were 170.8 excluding the head, the face and the neck. The average numbers of body scrub with right hand were 70.2, left hand were 88.2, and both hands were 81.8. The percentages of body scrub frequencies were 16.3% (breast), 12.2%(crotch), 8.8% (abdomen), 7.5% (waist), 8.8% (shoulder), 7% (hips), 0.4% (back), 15.2% (arm), and 23.9% (leg). Elders scrubbed the breast, crotch and abdomen more frequently than the back and hips. According to the video analysis and questionnaire results, the distribution of shower heads (or nozzles) at the front side should be arranged at the ratio of 40% of the trunk(breast, shoulders, abdomen), 20% of the thighs, the calves, and the crotch, respectively. The distribution of shower heads (or nozzles) of the back side were arranged at the ratio of 20% of the waist and the arms, 20% of the back, the thighs, the calves, and the hip, respectively.

• Journal of information and communication convergence engineering
• /
• v.4 no.4
• /
• pp.170-173
• /
• 2006

Recently, with increasing efficiency of DSC (photo-electrochemical using a nano-particle), The Performance of DSC solar generation system also needs improvement. The approach consists of a Fly-back DC-DC (transfer ratio 1:10) converter to boost the DSC cell voltage to 300VDC. The four switch (MOSFET) inverter is employed to produce 220V, 60Hz AC outputs. High performance, easy manufacturability, lower component count., safety and cost are addressed. Protection and diagnostic features form an important part of the design. Another highlight of the proposed design is the control strategy, which allows the inverter to adapt to the: requirements of the load as well as the power source. A unique aspect of the design is the use of the DSP TMS320LF2406 to control the inverter by current and voltage feed-back. Efficient and smooth control of the: power drawn from the DSC Cell is achieved by controlling the front end DC-DC converter in current mode.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.21 no.4
• /
• pp.165-179
• /
• 2019

This study used 3D body scan data to classify body shapes according to the torso shape of adult males aged 20-75 years. This data will be provided so that the apparel industry can make apparel products corresponding to body characteristics by age. The study used 1,796 adult males between the ages of 20 and 75 and the 3D body shape data of the '5th Research on National Standard Anthropometry'. For data analysis, the program SPSSWIN Ver. 17.0 was used to calculate the mean and frequency allowing for a factor analysis, cluster analysis, analysis of variance, and Duncan test. To classify body shape according to the torso shape of adult males, this study considered nine factors: 'horizontal size of torso,' 'vertical size of body,' 'curve of torso and waist-abdomen flatness ratio,' 'length of torso,' 'shape of neck area,' 'degree of lateral curve,' 'difference between front and back interscye length,' 'shoulder armscye shape,' and 'chest flatness ratio.' Based on the results of the factor analysis, the torso shapes of adult males were classified into five types. Type 1 is "upright body with flat, curvy shape", Type 2 is "curve sway back body type", Type 3 is "flat, abdominally obese body", Type 4 is "obese, crooked body" and Type 5 is "thick sway front body type." named.

• Journal of Korea Multimedia Society
• /
• v.14 no.2
• /
• pp.171-181
• /
• 2011

A vision-based method for positioning and orienting of pallets is presented in this paper, which guides autonomous forklifts to engage pallets automatically. The method uses a single camera mounted on the fork carriage instead of two cameras for stereo vision that is conventionally used for positioning objects in 3D space. An image back-projection technique for determining the orient of a pallet without any fiducial marks is suggested in tins paper, which projects two feature lines on the front plane of the pallet backward onto a virtual plane that can be rotated around a given axis in 3D space. We show the fact that the rotation angle of the virtual plane on which the back-projected feature lines are parallel can be used to describe the orient of the pallet front plane. The position of the pallet is determined by using ratio of the distance between the back-projected feature lines and their real distance on the pallet front plane. Through a test on real pallet images, we found that the proposed method was applicable to real environment practically in real-time.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.1-31.1
• /
• 2009

Carbon nanotubes (CNTs) are attractive material because of their superior electrical, mechanical, and chemical properties. Furthermore, their geometric features such as a large aspect ratio and a small radius of curvature at tip make them ideal for low-voltage field emission devices including backlight units of liquid crystal display, lighting lamps, X-ray source, microwave amplifiers, electron microscopes, etc. In field emission devices for display applications, the phosphor anode is positioned against the CNT emitters. In most case, light generated from the phosphor by electron bombardment passes through the anode front plate to reach observers. However, light is produced in a narrow depth of the surface of the phosphor layer because phosphor particles are big as much as several micrometers, which means that it is necessary to transmit through the phosphor layer. Hence, a drop of light intensity is unavoidable during this process. In this study, we fabricated a transparent cathode back plate by depositing an ultra-thin film of single walled CNTs (SWCNTs) on an indium tin oxide (ITO)-coated glass substrate. Two types of phosphor anode plates were employed to our transparent cathode back plate: One is an ITO glass substrate with a phosphor layer and the other is a Cr-coated glass substrate with phosphor layer. For the former case, light was radiated from both the front and the back sides, where luminance on the back was ~30% higher than that on the front in our experiments. For the other case, however, light was emitted only from the cathode back side as the Cr layer on the anode glass rolled as a reflecting mirror, improving the light luminance as much as ~60% compared with that on the front of one. This study seems to be discussed about the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the cathode back side. The experimental procedures are as follows. First, a CNT aqueous solution was prepared by ultrasonically dispersing purified SWCNTs in deionized water with sodium dodecyl sulfate (SDS). A milliliter or even several tens of micro-liters of CNT solution was deposited onto a porous alumina membrane through vacuum filtration. Thereafter, the alumina membrane was solvated with the 3 M NaOH solution and the floating CNT film was easily transferred to an ITO glass substrate. It is required for CNT film to make standing CNTs up to serve as electron emitter through an adhesive roller activation.

• Fashion & Textile Research Journal
• /
• v.9 no.4
• /
• pp.418-424
• /
• 2007

The purpose of this study is to propose a standard of converting 3D shape of men in twenties to 2D patterns. This can be a basis for scientific and automatic pattern making for high quality custom clothes. Firstly, representative 3D body shape of men was modeled. Then the 3D model was divided into 3 shells, front, side and back. Among them, the front shell was divided into 4 blocks by bust line and princess line. Secondly, curves are generated on each block according to matrix combination by grid method. Then triangles were developed into 2D pieces by reflecting the 3D curve length. The grid was arranged to maintain outer curve length. Next, the area of developed pieces and block were calculated and difference ratio between the block area and the developed pieces' area is calculated. Also, area difference ratio by the number of triangles is calculated. The difference ratio was represented as graphs and optimal section is selected by the shape of graphs. The optimal matrix was set considering connection with other blocks. Curves of torso upper front shell were regenerated by the optimal matrix and developed into pieces. We validated it's suitability by comparing difference ratio between the block area and the developed pieces' area of optimal section. The results showed that there was no significant difference between block area and the pieces' area developed by optimal matrix. The optimal matrix for 2D developing could be characterized as two types according to block's shape characteristics, one is affected by triangle number, the other is affected by number of raws more than columns. Through this study, both the 2D pattern developing from 3D body shape and 3D modeling from 2D pattern is possible, so it's standardization also possible.

• Korean Journal of Human Ecology
• /
• v.16 no.3
• /
• pp.577-585
• /
• 2007

This research aimed for 20 latter man whose body shape of torso alters remarkably to develop nipper pattern of running type considered characteristic of body shape of 20 latter man to keep rather balanced body shape against middle age when body shape changes extremely. 1. running type nipper pattern design. Pattern of running, lining and nipper were designed by flattening surface shell. A basis line of running pattern is completed by applying reduction ratio after 3 times of modification & complement based on surface shell. Nipper pattern is designed with design line set by a plaster cast based on running pattern line. Lining pattern is designed with lining design line set by a plaster cast based on running type outside material and nipper pattern. 2. Functional evaluation of research and commercial nipper. Functional inspection through dress test was applied 5point evaluation method and the result of functional inspection on the sight of a wearer is that research nipper(running reduction ratio 15%, nipper reduction ratio 18%) averaged more 4.8point but commercial nipper averaged less 1.8point in the aspect of 20 items such as wear sensibility, motional function and external appearance aesthetic. Research running type nipper scored high in order of motional function, looks of side, back, front and whole and wear sensibility. Functional inspection in the point of view of an observer is that research nipper(running reduction ratio 15%, nipper reduction ratio 18%) averaged over 4.8point and commercial nipper averaged under 1.9point in 17 items of external appearance beauty. Research running type nipper marked high in order of looks of back, whole, front and side.

• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.42-48
• /
• 2004

Lean laminar premixed propane and methane flames which were anchored by a hydrogen-pilot flame in a tube were investigated experimentally. The flame shapes were observed by varying mean velocity from 10cm/s to 140cm/s and equivalence ratio from 0.45 to 0.8. In this study, behaviors of flames are divided into five regions such as tail-out, flash-back, flickering, stable and vibrating flames with respect to the mean velocity and the equivalence ratio. Although the flames are unstable in both the flickering and the vibrating region, they have different characteristics such as the frequency, sound generation and creation process of flame curvature. The flickering region exists near the flammability limit and the flame flickers in a frequency of about 10Hz. When flame front is bended, the propane flame front is straightened and the methane flame front is bended more by thermo-diffusive instability. In the vibrating region, the flame vibrates emitting audible sound in a frequency of about 100Hz. In the boundary of vibrating region, the vibration of flame changes between two modes such as single frequency vibration and dual frequency vibration. Increase and decrease of vibration in each mode are determined by thermo-acoustic instability.

• Fashion & Textile Research Journal
• /
• v.12 no.4
• /
• pp.467-476
• /
• 2010

The purpose of this study was to develop a plausible methodology based on experimental data how to set up darts and split lines on 3D parametric body dressed with tight-fit garment. The results were as following: Through the process of making convex hull, the concave parts were straightened to make a convex hull, especially in the center part of bust, under breast part and scapular part. To figure out the optimum positions of darts and split lines, the inflection points of curve ratio were searched along the horizontal polylines of waist and bust. This procedures produced reliable results with low deviation. Using Rapidform, CATIA and Unigraphics, six patches of bodice patterns were drawn and aligned. Paired t-test results showed the outline and area between 3D surface and 2D were not significantly different, meaning this method could be adaptable when flattening 3D surfaces. The amount of waist dart measured on the pattern showed that the highest portion was allocated on 2nd dart(back), followed by 1st dart(back), 1st dart(front), 2nd dart(front)/side dart, and center back dart. A series of findings suggested that curve ration inflection point could be used as a guide to set up darts and split line on 3D parametric model with low deviation.

• Fashion & Textile Research Journal
• /
• v.13 no.5
• /
• pp.661-671
• /
• 2011

This study was designed to produce rounded belt pattern and tight-skirt pattern drafting method using 3D body scan data. Subjects were thirty women in their early twenties. In order to figure out the optimum cutting points, namely, where darts are made, using CAD program, curve ratio inflection points on the horizontal curve of waist, abdomen, and hip to find 1 point in the front, two points in the back part. The average length from center front point to maximum curve ratio was 7.7 cm(46.3%) on the waist curve; 7.9 cm(39.4%) on the abdomen curve. And the average length from center back point to maximum curve ratio point was 6.9 cm(39.0%) for first dart and 11.2 cm(63.3%) for second dart on the waist curve; 8.9 cm(35.8%) for first dart and 15.7 cm(63.3%) for second dart on the hip curve respectively. The cutting lines from were made up by connecting curve inflection points. After divided using cutting lines, each patch was flattened onto the plane and all the technical design factors related with patternmaking were measured, such as dart amount, lifting amount of side waist point, etc. Based on the results of correlation analysis among these factors, regression analysis was done to produce equations to estimate the variables necessary to draw up pattern draft method; F1=F8+1.1, $F4=2.5{\times}F2+0.9$, $F5=0.9{\times}F4+1.0$, $F6=0.3{\times}F4+0.4$, $B1=0.9{\times}B8+2.3$, $B4=2.1{\times}B2+1.3$, $B5=0.9{\times}B4+3.5$, and $B6=0.3{\times}B4+0.4$.