• Phonetics and Speech Sciences
• /
• v.11 no.4
• /
• pp.97-108
• /
• 2019

An automated Praat script was implemented to measure optimal formant frequencies for adults. Optimal formant analysis could be interpreted to show that the deviation of formant frequency that resulted from the two variously combined setting parameters (maximum formant and number of formants) was minimal. To increase the reliability of formant analysis, LPC order should be set differently, based on the gender or vowel type. Praat recommends 5,000 Hz and 5,500 Hz as maximum formant settings and, at the same time, recommends 5 as the number of formants for males and females. However, verification is needed to determine whether these recommended settings are valid for Korean vowels. Statistical analysis showed that formant frequencies significantly varied across the adapted scripts, especially with respect to the data on females. Formant plots and statistical results showed that linear_script and qtone_script are much more reliable in formant measurements. Among four kinds of scripts, the linear and qtone_scripts proved to be more stable and reliable. While the linear_script was designed to have a linearly increased formant step in for-loop, the increment of formant step in the qtone_script was arranged by quarter tone scale (base frequency×common ratio ($\sqrt[24]{2}$)). When looking at the tendency of the formant setting drawn by the two referred algorithms in the context of front vowel [i, e], the maximum formant was set higher; and the number of formants set at a lower value than recommended by Praat. The back vowel [o, u], on the contrary, has a lower maximum formant and a higher number of formants than the standard setting.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.278-285
• /
• 1991

The authors propose to use the slot system in order to improve of the efficiency for the cambered otter boards. The experiment is divided into 2 parts, one is the efficiency model test, and the other is the visualization model test. The hydrodynamic characteristics of the model otter boards were tested by efficiency model test to measure the shearing, drag force of the models and visualization test using hydrogen bubble method to observe the streak-line and time-line of flow around the models, and milk spout method to observe the separation zone in the wake behind the models. This study tested for 5 models such ad without slot, slot position 0.2C, 0.4C, 0.6C and 0.8C. The results obtained are as follows: \circled1 The maximum C sub(L) of model otter board with slot position 0.6C in attack angle 27$^{\circ}$ was the highest of all models, it's value was 1.59. \circled2 In general, the L/D ratio of the one slot otter boards were 16~28% higher than otter board without slot. \circled3 The slot position 0.6C was better than any other slot position, and it's conformed by visiualization. \circled4 As to the model otter board with slot position 0.6C, flow speed of the back side was faster 1.3 to 1.7 times than in the front side. \circled5 The size of the separated zone in case of the model otter board with 0.6C was smaller than that of any other models.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.4
• /
• pp.1908-1914
• /
• 2013

In this paper, we introduce a design method for a broadband planar quasi-Yagi antenna (QYA) for terrestrial digital television (DTV) reception. The coplanar strip line which feeds the driver dipole is connected to a microstrip line and is terminated by short circuit. By appending a wide strip-type rectangular director at a location close to the driver dipole, broadband impedance matching and gain enhancement in a high frequency region are obtained. The gain characteristics in a low frequency region are improved by adding a reflector formed by a truncated ground plane. To reduce the antenna size, the strip-type dipole and reflector are modified to half bow-tie (V)-shaped elements. The effects of various parameters on the antenna characteristics are examined. An antenna, as a design example for the proposed antenna, is designed for the operation in the frequency band of 470-806 MHz for terrestrial DTV. The optimized antenna is fabricated on an FR4 substrate and the experimental results show that the antenna has a good performance such as a frequency band of 450-848 MHz for a VSWR < 2, gain > 4.1 dBi, and front-to-back ratio > 10.4 dB.

• Journal of the Korean Society of Radiology
• /
• v.5 no.3
• /
• pp.143-148
• /
• 2011

The purpose of this study was to examine the usefulness of SPIO contrast agent in Magnetic Resonance Cholangiopancreatography (MRCP) by performing a quantitative comparative analysis in patients undergoing MRCP for gallbladder stones with and without oral injection of SPIO (Superparamagnetic iron oxide) contrast agent. The subjects were 36 patients undergoing MRCP for suspected gallbladder stones between January 2009 and February 2010 and they were divided into halves to compare the two groups of with and without SPIO agent. For each subject in both the injected and non-injected group, T2-weighted images on a 1.5T MR scanner were obtained, using both the breath-holding and respiratory-triggered methods, respectively. The following regions were measured; for breath-hold T2-weighted images, the measurement regions were located at the central part of the gallbladder, and the areas 15 mm away from its center, toward the front and back, respectively, which were chosen to include surrounding tissues, while for respiratory-triggered T2-weighted images, at the central part of the gallbladder, and segment 5 and 6 of liver. In a quantitative analysis, average signal to noise ratio (SNR) in each of regions of interest (ROI) for each group were calculated and then average contrast to noise ratio (CNR) in each of ROI were obtained by using the SNR in the gallbladder as the basis to compare and analyze the values between the two groups. The CNR were higher for the injected group in those regions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.4165-4170
• /
• 2012

In this paper, a method for the improvement in the gain and bandwidth of a microstrip-fed broadband planar quasi-Yagi antenna (QYA) is studied. The broadband characteristics of the QYA are achieved from the coplanar strip-fed planar dipole driver and a parasitic director close to the driver. In order to obtain stable gain variation over the required frequency band, a director and a ground reflector are appended to the driver having a nearby parasitic director. The QYA is fed through an integrated balun composed of a microstrip line and a slot line which are terminated in a short circuit. By adjusting the feeding point, a broadband impedance matching is obtained. A QYA with an operating frequency band of 1.75-2.7 GHz and a gain > 4.5 dBi is designed and fabricated on an FR4 substrate with dielectric constant of 4.4 and thickness of 1.6mm. The experimental results show that the fabricated antenna has good performance such as a broad bandwidth of 59.7%(1.55-2.87 GHz), a stable gain between 4.7-6.5 dBi, and a front-to-back ratio > 10 dB. The measured data agree well with the simulation, which validates this study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.11
• /
• pp.5214-5218
• /
• 2011

In this paper, bandwidth improvement of a series-fed two dipole array(STDA) antenna applicable for mobile communication base station antennas is studied. The proposed STDA antenna consists of two strip dipole antennas with different lengths which are connected directly trough a coplanar stripline(CPS). By adjusting the spacing between the two dipoles and the length of the second dipole, the bandwidth of the STDA can be enhanced. In addition, an integrated balun composed of a short-circuited microstrip line and a slot line is utilized to minimize the area required for a feeding part, and a broadband impedance matching is obtained by adjusting the feeding point. Based on the proposed antenna structure, an STDA antenna covering the frequency band ranging from 1.75 GHz to 2.7 GHz, which includes almost all the existing mobile communication frequency bands, with more than 5 dBi gain is designed and fabricated on an FR4 substrate with dielectric constant of 4.4 and thickness of 1.6mm, and experimentally tested. The fabricated antenna shows impedance bandwidth of 49%(1.7-2.8 GHz) for VSWR<2, a gain higher than 5.5 dBi, and a front-back ratio better than 12 dB.

• Journal of Conservation Science
• /
• v.32 no.4
• /
• pp.579-588
• /
• 2016

This study analyzed nonmetallic inclusions in iron swords with a ring pommel excavated in the Ipbuk-dong, Suwon. Scanning electron microscopy with energy dispersive spectroscopy(SEM-EDS) was used to estimate the iron-making temperature, and we compared the oxide with $SiO_2$ to investigate the heat-treatment technology in the production of iron swords with a ring pommel by investigating the artificial insertion of a slag former and the metallurgical structure. From the wustite observed in most of the specimens, it is judged that these swords were produced by heating and forging iron smelted at a low temperature using the solid reduction method. In addition, judging from the partial presence of $P_2O_5$, it is assumed that they were smelted directly with natural ore, not calcined. From the ratios of $CaO/SiO_2$ and $TiO_2/SiO_2$, it is judged that the raw material for iron-making was iron ore and that a calcareous slag former was not artificially inserted. The structure of the blade part on the front end was pure iron. From the high carbon content of the blade part on the ring pommel and the formation of a martensitic structure and pearlite colony, it is judged that they were tempered after carburizing and that the back, handle part, and ring pommel were unintentionally carburized. Judging from the structure of these specimens, it was noted that they were produced by applying artificial partial heat-treatment technology. This study attempted to present a more scientific analysis by using the method of interpretation through component analysis of nonmetallic inclusions appearing in one relic by the ratio of the oxide divided by $SiO_2$. It is judged that reinterpreting the arguments by the results of the existing analysis and research in this way can obtain different interpretations.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.2
• /
• pp.286-291
• /
• 2006

The objective of the present study was to investigate the effects of growth performance, chemical composition and meat quality parameters by the addition of fermented persimmon shell diets (FPSD). The experimental animals were ninety-six Berkshires. The pigs were allotted at 8 per pen in front-open building with three replicate pens per treatment. Until $61{\pm}1kg$ live weight at 140 days, the animals were fed growing diet, after which, experimental samples were fixed at 0, 3, 5 and 7% FPSD as C, T1, T2 and T3 in the finishing diets. Pigs of $103{\pm}1kg$ live weight were slaughtered by electrical stunning. In growth performance, ADG increased more (p<0.05) in T2 than C and T1. ADFI (kg/day) was higher (p<0.05) in T2 than in other groups. Feed conversion ratio was lower (p<0.05) in T2 than in other groups. On longissimus dorsi muscle (LM), the content of moisture was lower (p<0.05) in T3 than in other treatments. Crude fat increased (p<0.05) by addition of FPSD. pH at 24 h ($pH_{24}$) decreased more (p<0.05) in T2 and T3 than C and T1 by addition of FPSD. WHC decreased (p<0.05) by addition of FPSD. In meat, Hunter $L^*$ and $a^*$ were lower (p<0.05) in C than in other treatments. Hunter $b^*$ was higher (p<0.05) in T3 than in other treatments. In back-fat, Hunter $L^*$ was higher (p<0.05) in C than in other treatments. Hunter $a^*$ was not different in C and T1 but increased (p<0.05) in treatments by addition of FPSD. Hunter $b^*$ increased (p<0.05) by addition of FPSD. In sensory evaluation scores, for fresh meat, the value of meat color was higher (p<0.05) in T2 and T3 than in C and T1. The value of marbling was lower (p<0.05) in C than in other treatments. The value of drip loss was higher (p<0.05) in C than in other treatments and was lower (p<0.05) in T2 and T3 than in other treatments. The results of cooked meat, the value of tenderness was not different in C and T1 but increased (p<0.05) in other treatments. The value of flavor was significantly higher (p<0.05) in T2 and T3 than in C and T1. The value of overall acceptability was increased (p<0.05) by addition of FPSD. Hence we can conclude that addition of FPSD affected growth performance and meat quality parameters, in particular, it improved crude fat, hunter $L^*$ and $b^*$, and sensory evaluation on pork and was also seen to affect $pH_{24}$ and WHC. FPSD can be used for improvement of meat quality parameters.