• 대한기계학회논문집B
• /
• 제23권10호
• /
• pp.1265-1273
• /
• 1999

PIV(Particle Image Velocimetry) velocity field measurements inside the snout of a1/10 scale model of the Zn plating process were carried out at the strip speed $V_s=1.5m/s$. Aluminum powder particles ($1{\mu}m$) and atomized olive oil ($3{\mu}m$) were used as seeding particles to simulate the molten Zinc flow and deoxidization gas flow, respectively. A pulsed Nd:Yag laser and a $2K{\times}2K$ high-resolution CCD camera were synchronized for the PIV velocity field measurement. From flow visualization study, it is found that the liquid flow in the Zn pot is dominantly governed by the uprising flow caused by the rotating sink roll, with its effect on the steel strip inside the snout largely diminished by installing of the snout. The deoxidization gas flow in front of the strip inside the snout can be characterized by a large-scale vortex rotating clockwise direction formed by the moving strip. In the rear side of the strip, a counter-clockwise vortex is formed and some of the flow entrained by the moving strip impinges on the free surface of molten zinc. The liquid flow in front of the strip is governed by the flow entering the snout, caused by the spinning sink roll. Just below the free surface a counter-clockwise vortex is formed near the snout wall. The moving strip affects dominantly the flow behind the strip inside the snout, and large amount of the liquid flow follows the moving strip toward the sink roll. The thickness of the flow following the strip is very thin in the front side due to the uprising flow, however thick boundary layer is formed in the rear side of the strip. Its thickness is increased as moving downstream toward the sink roll. Inside the snout, the deoxidization gas flow above the free surface is much faster than the liquid flow in the zinc pot. Due to the larger influx of the flow following the moving strip in the rear side of the strip, higher percentage of imperfection can be anticipated on the rear surface of the strip.

• 한국지반신소재학회논문집
• /
• 제16권4호
• /
• pp.139-149
• /
• 2017

석굴암이 발견된 이후 수행된 그간의 정비 및 보수 보강 사업과 구조안정성 평가는 주로 석굴암의 석재와 콘크리트 돔 구조체의 상태 점검을 위주로 진행되어 왔다. 그러나, 석굴암 배면에는 높이 12m의 암반비탈면이 위치하여 비탈면 붕괴나 낙석 등의 발생이 우려되고, 이는 석굴암의 안정을 저해하는 요인이 될 수 있다. 또한 석굴암 측면 및 전면부의 토사비탈면과 석축의 경우도 최근 빈번해지고 있는 국지성 호우와 지진의 영향으로 장기적으로 안정성을 확보하고 있는지 의문시된다. 이에 본 연구에서는 석굴암 주변 지반과 비탈면에 대한 상세 현장조사를 통해 지형 및 지질학적 위험요인들을 파악하고, 안정성 해석을 통해 석굴암 배면의 노출암반 및 전면부 비탈면과 석축 등의 구조적 안전성을 검토하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2648-2653
• /
• 2007

Recently, increasing demand on not only lighter but also extremely mobile battery make micro fuel cell device very attractive alternative. By reducing the size of fuel cell, surface tension becomes dominant factor with minor gravitational effect. Therefore, it is very difficult to detach the $CO_2$ bubble generating on a cathode side in ${\mu}DMFC$ (micro direct methanol fuel cell). The degassing of a $CO_2$ bubble has drawn quite attention especially for ${\mu}DMFC$ due to its considerable effect on overall machine performance. Our attention has been paid to the dynamic behavior of immiscible bubble attached to the one side of the wall on 2D rectangular channel subject to external shear flow. We use Level Contour Reconstruction Method (LCRM) which is simplified version of front tracking method to track the bubble interface motion. Effects of Reynolds number, Weber number, advancing/receding contact angle and property ratio on bubble detachment characteristic has been numerically identified.

• 한국연소학회지
• /
• 제6권1호
• /
• pp.1-6
• /
• 2001

To evaluate the effect of lobed structure on pollutant emission, an experimental study examines NOx and CO emissions associated with four burner geometries, such as a conventional circular burner and three lobed ones. Rapid mixing allowed by the lobed burner to produce lean premixed flames, with narrower flame stability diagram than for the conventional circular one. Conventional circular burner of wide and uniform burner rim has an advantage of flame stabilization. Correlation on fuel discharge velocity for flame blowout should be included a variable related to the wall effect of the burner. NOx emission reduces by about 5% at the burner with lobed structure in fuel discharge side compared to conventional circular one. This is due to lower flame temperatures through flame elongation and increased radiative heat losses, caused by partially luminous flame in flame front. Meanwhile, at the burner with lobed structure in air discharge side and both fuel and air discharge sides, NOx emission somewhat increases with reduced radiative heat losses in spite of flame elongation. Therefore, the rapid mixing by lobed structure does not always have an advantage on NOx reduction.

• 플랜트 저널
• /
• 제13권2호
• /
• pp.46-51
• /
• 2017

본 연구에서는 정격출력 870MW, 대향류 석탄보일러의 최상부층 버너운전에 따른 보일러 연소상태 변화와 보일러 효율을 측정하였다. 시험방법은 하부와 중간층 버너가 운전중인 상태에서 최상부층 전방버너, 전,후방 버너 동시 운전, 후방 버너 운전으로 구분하여 최상부층 버너 운전에 따른 보일러 효율을 측정하였으며 시험 결과 최상부층 전 후방 버너 동시운전 > 최상부층 전방 버너 > 최상부층 후방 버너 운전의 순으로 보일러 효율이 높게 나타났다. 최상부층 전방과 후방 버너를 동시에 운전할 경우 보일러 노 내 열흡수율 증가 및 대류전열면 좌우 증기온도 편차가 감소되었다. 보일러 열흡수율 개선에 따라 보일러 배기가스손실 감소 및 석탄공급량이 후방버너 운전 대비 8t/h 감소하였으며, 이는 연료비 절감은 물론 온실가스 배출량 감축에도 크게 기여할 것으로 판단된다.

• 한국농촌건축학회논문집
• /
• 제7권1호
• /
• pp.73-87
• /
• 2005

The purpose of this study is aimed at grasping the architectural characteristics of modern buildings in Gangneung from 1910's to 1970's. The results are as follows. 1) The commercial buildings are mostly unsymmetrical flat type and others except commercial buildings are mostly symmetrical flat type. 2)Up until the 1940's, staircases were located inner of building between the first and the second floor, however after the 1950's, they were separately located in one side of the building to ensure perpendicularly more space and easier mobility than before. 3)Windows were widely used in order to avoid monotonous wall elevation after 1950' s. 4)Striped decorations were put to use to decorate the front elevation of building. 5)Parapet which had decorative stripes to the top was generally used to hide roof.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.848-851
• /
• 2004

This paper studied a method for minimizing the noise level emitted from range hoods. Range hoods were used for discharging various hazardous materials generated during household cooking to the outdoors, thus preventing them from being diffused through rooms in the house since they are the main cause of air pollution within dwellings. This study assumed that static pressure was not applied at the discharge outlet of the range hood. As such, the range hood was installed on the wall without the use of a connecting duct or other connectors attached to its discharge outlet. The vibration having the greatest influence on the noise level was determined by measuring the vibration at the front side of the hood where the acoustic omission was at its maximum. A method was then proposed to reduce the noise by simply suppressing the vibration at the vibrating part.

• 설비공학논문집
• /
• 제28권11호
• /
• pp.458-465
• /
• 2016

The purpose of this research is to improve the thermal effiency of solar collector and to quantitatively analyze its performance. Solar thermal systems have been limited to water heating systems mainly using low-temperature range. However, through diverse developments, the application has been extended to medium- and high-temperature fields such as solar heating, solar air conditioning, and solar thermal industrial process. Among the diverse research, this research is specially focusing on enhancement of the thermal performance by minimizing the heat loss coefficient of flat plate solar collectors. In order to do it, a front-side glazing material and a back-side insulation material with high insulated structure is proposed and based on computational analysis, the performance of energy collecting volume of the proposed solar collector is analyzed. The research shows that the proposed structure has the excellent performance at medium- and high-temperature range. therefore, it is expected that the proposed structure can easily replace existing technologies.

• 한국농촌건축학회논문집
• /
• 제14권4호
• /
• pp.67-76
• /
• 2012

The main purpose of this study is to understand the existing and the architectural characteristics of the Secondary Stations of Catholic Church in Jeju. The method of this study is to research all the literature and to visit. The time of establishment of the Secondary Stations of Catholic Church in Jeju was mostly 1950's, and that time was the heyday of the Secondary Stations of Catholic Church that was built in Korean. Catholicism was spread throughout Jeju during this time, and in the process, the Secondary Stations of Catholic Church was built. The Secondary Stations of Catholic Church in Jeju are sited mostly in coastal villages, and especially Catholicism was actively spread throughout the west of Jeju and the a large number Secondary Stations of Catholic Church were built in the west of Jeju. The Secondary Stations of Catholic Church were built between the mid-1950's to the mid-1960's. The plan type is kept as plan shaped of straight shape. When made an enlargement of the interior space and altered, framework of the Secondary Stations of Catholic Church was generally maintained. The head of the side window and the front door have the same design characteristics. When the belfry is located, it is attached to an outer wall of the Secondary Stations of Catholic Church, or is located to the left or the right the front of the Secondary Stations of Catholic Church. The design of belfry found expression in various forms. The buttress are not located in the others but in Young-su Gong-So, and it has not the structural functions but the design functions.

• 한국안전학회지
• /
• 제5권2호
• /
• pp.66-75
• /
• 1990

This study is conducted to establish the structural standard of tube and coupler scaffold which is suitable for our present stuation through the comparison analysis for domestic and foreign standards as well as measurement of field survey. The results of this study are as follows ： 1) The load is classified by three categories, light-duty(equal and lower than 150kg/m$^2$), medium-duty(150-250 kg/m$^2$), heavy-duty(250-350kg/m$^2$), and the equivalent horizontal length of side posts is each, 1.5-1.8m, 1.2-1.5m, equal and lower than 1.2m, and the equivalent horizontal length between front and rear posts is each 1.2-1.5m, 0.9-1.2m, equal and lower thatn 0.9m, in accordance with the load classification. 2) The height between upper and lower runner is equal and lower than 1.5m, and the brace across the width of scaffold should be installed within 15m in horizontal direction at 45 degree angle. 3) The entire scaffold should be securely tied to the wall of permanent structure with uslng anchor and bolt at intervals not to exceed 6m in case of non-connection and 4.5m in case of connection in both horizontal and vertical direction. 4) The post should be installed on the sound foundation tied to lumber footing with using base plate, and standard platform plank should be produced in the factory and widely used in the construction field.