• Journal of the Korea Concrete Institute
• /
• v.27 no.2
• /
• pp.103-113
• /
• 2015

This paper studies impact performance of wire-mesh and steel fiber-reinforced concrete based on high-velocity impact experiments using hard spherical balls. In this experimental study, panel specimens were tested with various parameters such as steel fiber volume fraction, presence/absence of wire mesh, panel thickness, impact velocity, and aggregate size for the comparison of impact resistance performance for each specimen. While improvement of the impact resistance for reducing the penetration depth is barely affected with steel fiber volume fraction, the impact resistance to scabbing and perforation is improved substantially. This was due to the fact that the steel fiber had bridging effects in concrete matrix. The wire mesh helped minimizing the crater diameter of front and back face and enhanced the impact resistance to scabbing and perforation; however, the wire mesh did not affect the penetration depth. The wire mesh also reduced the bending deformation of the specimen with wire mesh, though some specimens had splitting bond failure on the rear face. Additionally, use of 20 mm aggregates is superior to 8 mm aggregates in terms of penetration depth, but for reducing the crater diameter on front and back faces, the use of 8 mm aggregates would be more efficient.

• Journal of the Korean Geosynthetics Society
• /
• v.23 no.2
• /
• pp.1-7
• /
• 2024

Various innovative technologies and methods are being applied to ensure the stability of steep rock slopes. However, there are design limitations concerning site ground conditions, leading to discrepancies between the designed and actual ground conditions during construction. In the case of the retaining wall in Yeosu, where the study area is located, although the construction of a 5-stage retaining wall is planned, at the current completion of the second stage, cracks on the upper part of the wall, settlement in the front of the wall, and seepage have been observed. After the completion of stages one and two, issues regarding cracks and settlement on the upper part of the wall and seepage in the front of the wall were discovered. Thus, there was a need to reevaluate the results of the existing stability assessment. It was confirmed that the issue was due to groundwater leakage, attributed to the lack of clear assessment of the colluvial soil layer during the initial design stage. Therefore, to conservatively reflect groundwater level conditions, a groundwater level contour was positioned at the top of the wall to conduct a slope stability assessment. The assessment results indicated that the safety factor during the rainy season exceeded the required value of 1.3, with a calculated safety factor of 1.31. However, during seismic events, the safety factor was determined to be 1.12, falling short of the required safety factor of 1.3. Therefore, it is suggested that the existing retaining walls constructed during stages one and two undergo reinforcement using methods such as micro-piles with grouting, and additional work should be carried out to ensure a clear assessment of the colluvial soil layer.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.98-103
• /
• 2001

A new application of dirchroic mirror for the improvement of luminance and luminous efficacy in an AC-Plasma Display Panel (PDP) is suggested. Only about half of the Vacuum Ultraviolet (VUV) generated in the reflective PDP cell is used for the excitation of the phosphor. We are suggesting an idea of adopting a dichroic mirror which can reflect the VUV toward the phosphor which otherwise is absorbed by the front panel. The optical constants of the thin films of dirhroic mirror were determined from the photometric measurements through an iteration process of matching calculated and measured values of the reflectance and transmittance in the VUV wavelength region. From these results, we could design such a filter whose high reflection zone is centered at 147nm by a computer simulation accurately. The 147nm VUV is radiated from Xenon 3Pl state which is dominantly used to activate the phosphor in the PDP cell. The dichroic mirror was made with an electronbeam evaporator and its reflectance was measured by a reflectometer. We confirmed the usefulness of the dichroic mirror for the improvement of efficiency with experiments done by test panels. The panel with mirror shows improved luminance and luminous efficacy by 20∼30％.

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.3
• /
• pp.339-344
• /
• 2014

Purpose: This study relates to the development of the day and night scope using the reflecting surface of a BS (beam splitting) prism. Methods: We have placed the LCD panel and the dot reticle generator to the top and bottom of the reflecting surface of the BS prism, and have placed a reflector, which is designed to doublet type, in the front of the BS prism. Doing so, we have developed a new type of day and night scope, which is able to image the virtual image of dot reticle from the dot reticle generator to the direction of the observer, to make the observer survey the peripheral information of the outside target by 1x magnification, and to make the observer survey the image of the LCD panel directly. Results: We could develope a new type of day and night scope, which has the function of night scope as thermal image display device at night time and the function of day scope as dot sight at day time, by letting the reflective surface of the BS prism have the role of dot sight which reflects the dot reticle and have the role of reflective optical system by which the observer surveys the night thermal image displayed in LCD panel. Conclusions: In this study, we have developed the new type of day and night scope which is able to play the role of the day or night scope selectively, combining the existing dot sight and the existing night scope by using the BS prism. By doing so, we could design and fabricate the new type of day and night scope with the BS prism which can further increase the rapidity of firing and provide more convenience in the mounting of a firearm than the detachable combination of an existing dot sight and an existing night scope.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.5
• /
• pp.608-614
• /
• 2018

In addition to the diffusion of ICT technology, various protocols of short range wireless communication technology are being applied for efficient information operation. However, due to limitations of short-range wireless communication, communication is not smooth in places where frequency environment is poor, such as frequency confusion and warehouse type factory. When an alternative is needed. The development of LED technology and expansion of infrastructure through LED based visible light communication is attracting attention as an alternative and spreading the usage in wide range now a days. In addition, the infrastructure has been expanded with solar panels in response to the development of smarthome built-in with renewable energy. In this situation, visible light communication using PD has been limitedly applied in a near environment where the receiving angle of the PD and the ambient light ensure the LoS and the influence of the ambient light is small. In order to solve this problem, we have implemented visible light communication using LED lighting with large current infrastructure and solar panel with large receiving area, and proposed a circuit for restoring accurate data even in ambient light. Through this study results, it is expected that visible light communication can be more widely used and this result used as the base data for visible light communication research using the solar panel as the receiver.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.12
• /
• pp.858-862
• /
• 2013

The front electrode should be used to make solar cell panel so as to collect electron. The front electrode is used by paste type, printed on the Si-solar cell wafer and sintered at about $800^{\circ}C$. The paste is composed Ag powder and glass frit which make the ohmic contact between Ag electrode and n-type semiconductor layer. From the previous study, the Ag electrodes which used two commercial glass frit of Bi-system were so different on the interface resistance. The main composition of them was Bi-Zn-B-Si-O and few additives added in one of them. In this study, glass frit was made with the ratio of $Bi_2O_3$ and ZnO on the main composition, and then paste using glass frit was prepared respectively. And, also, the paste using the glass frit added oxide additives were prepared. The change of interface resistance was not large with the ratio of $Bi_2O_3$ and ZnO. In the case of G6 glass frit, 78 wt% $Bi_2O_3$ addition, the interface resistance was $190{\Omega}$ and most low. In the glass frit added oxide, the case of Ca increased over 10 times than it of G6 glass frit on the interface resistance. It was thaught that after sintering, Ca added glass frit was not flowed to the interface between Ag electrode and wafer but was in the Ag electrode.

• Journal of the Korean Home Economics Association
• /
• v.29 no.2
• /
• pp.87-120
• /
• 1991

The purpose of this study was to identify the design characteristics of the multi-leveled chest(jang) which was the main furniture of the master bedrom(anbang) in the Chosun Dynasty. The major findings and conclusions were: 1. The front view of the multi-leveled chest were composed of a protruded top panel(kaepan), drawers, folded doors, sectional panels(chwibyok kan and morum kan) and base stand(madae) in general. Variety in the front view found more frequently in single level chests than bi- or tir-level chests. 2. The overall dimensions of each type of chest increased with increase in number of levels, but the height of the sectional parts decreased. That is, the overall proportion of the single level chests were 10 : 9, bi-level chests were 5 : 6, and tri-level chests were 2 : 3. The proportion of 1 : 1, 4 : 5, 1 : 3, 1 : 4, 1 : 5 were found often in the sectional parts such as drawers, doors, chwibyok kans and morum kans. 3. In general, the surface treatments were subtle. Carved or inlayed ornamentation were seldom seen, and most chess were finished with clear lacquer to show the natural wood grain. There were no distinctive characteristics of surface ornamentation characteristic of any one type of chest. 4. The general patterns of the metal ornaments were spade(yowidu), round, bow, rectangular(yakgua), bat and flower shapes. The multi-level chests were decorated with more metal ornament types compared with the single-level chests. 5. In conclusion, there was more variety in all the design elements in the single level chests compared with the other types of chests. The bi-and tri-level chests were quite stylized in composition, size, proportion, surface treatment, and metal ornamentation.

• Journal of Fashion Business
• /
• v.22 no.4
• /
• pp.30-46
• /
• 2018

The purpose of the study was to suggest certain measurements of the skirt block pattern drafting process for the Korean female fashion models, with the aim to improve its fit. For this purpose, the study carried out an analysis of the lower body features of a dress form developed for the study. This form was representative of Korean female fashion models' body features. The study performed a cross-sectional analysis at waist and hip levels and measured the angles from the frontal and lateral silhouettes of the dress forms. The comparisons of the skirt block patterns developed through draping by the use of 2 types of the dress forms developed and existed and through drafting according to the current patternmaking method have led to noticeable findings in terms of implementation of the skirt block drafting process for the Korean female fashion models. The results of the study are as follows: (1) the vertical lengths between the levels at the front waist point and the side waist point in the patterns are 0.7cm; (2) the vertical length between the levels at the front waist point and the back waist point in the back panel is 0.7cm; (3) the horizontal lengths between the perpendicular line from the side hip point and the side waist point in patterns are within a range of 2.0 to 2.2cm; (4) the horizontal length between the original and the adjusted back waist points moved into the waist line, in a range of 0.0 to 1.0cm, differs whether the center back line would be folded or sewn.

• Fashion & Textile Research Journal
• /
• v.17 no.3
• /
• pp.429-439
• /
• 2015

This study develops a new brassiere for new silver women. A new brassiere design was developed for the silver generation based on apreliminary survey; subsequently, a wire and no-wire type of brassier were developed after a second fitting evaluation. The results were as follows. First, in terms of brassiere design, the cup shape was designed as mold type full cup, shoulder straps were designed as camisole type with cups, bias tape was designed for body correction in the side line and mash tape was designed for easy movement below the cups. On the other side ofthe cup shape was a pocketdesigned on a support pad forthe wire type and a support panel to serve as a wire in the no-wire type brassiere. Second, brassiere patterns were designed by referencing the educational H pattern. Thetotal length was elongated by 5cmto reduce pressure when wearing a brassiere and the height of the front center increased by 8cm for the stability of the front center of the brassiere. In addition, the side line was moved back by 3cm and the width of the brassiere wings was designed widely at 10.5cm. Third, a wearing test was conducted for the wire type and the no-wire type brassiere with comparison products, using a 7-point Likert scale. Appearance results and movement tests for the wire and no-wire type showed a higher score than comparison products.

• Industry Promotion Research
• /
• v.4 no.2
• /
• pp.1-8
• /
• 2019

This research is a technology for cutting the insulation of the busbar (busbar) installed in the distribution panel or switchboard, the results of the study, first, the cutting unit and frame of the cutting unit including a housing attached to the upper and lower cutters, respectively Busbar coating laser cutting machine is installed on the top, characterized by consisting of a stopper for adjusting the coating cutting distance of the busbar. Second, the frame is installed with the guide bar in the longitudinal direction at the top so as to be located at the rear side end of the table, the post is installed vertically at the front and rear at the upper middle part, respectively, and cut to the table at the outer side of the front post. It is characterized by the formation of holes. Third, the supporter is fixedly installed on the upper part of the guide bar arranged in the frame, and is characterized by consisting of a cylinder and a support plate. The meaning of this study is to prevent the safety accidents of workers, to improve the efficiency of cutting work, and to prevent the occurrence of scratches on the surface of the busbar.