• 한국안전학회지
• /
• 제19권1호
• /
• pp.12-17
• /
• 2004

By using an experimental approach recently developed to determine the torque-tension relationship for bearing frictional characteristics of several typical bolted joints were studied. The experimental approach allows the direct determination of the bearing friction between the nut and its bearing surface. Detailed friction studies were made on the influences of the size and shape of the hole, the use of a slot in a bolted joint, contact area and position, and other factors such as turning speed, coating, and the use of wax on the bearing surface. The contact area and position of the washer have a marginal effect on the bearing friction. The organic coating on the nuts reduces the bearing friction significantly. Nuts with organic coating over a washer with zinc finish provide the smallest and the most consistent bearing friction. The results from the experimental investigation will be helpful for the better design of bolted joints bearing friction. The results from the experimental investigation Will be helpful for the better design of bolted joints.

• 한국자동차공학회논문집
• /
• 제3권3호
• /
• pp.79-89
• /
• 1995

Rattle noise occurs at manual transmission as idling and driving of a automotive. It can be solved by torsional characteristics of a clutch disc. A clutch disc consist of a region of pre-damper and main-damper. Rattle noise is affected by pre-damper and main-damper equipped for a torsional spring and friction washer. Pre-damper range covers noise radiating from manual transmission when engine is idling and main-damper range covers noise when engine is driving. The aim of this reserch is to clear transmission rattle noise by way of torsional characteristics of a clutch disc. The experiment is carried out as idling and driving of a automobile equipped for 1.5L MPI engine, dry single-disc type clutch and manual transmission. In this study, the results show for a vibration of manual transmission as idling and driving can be cleared by a clutch disc of Pre-damper type.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.996-1001
• /
• 2006

Automatic washing machines have been improved and popularized steadily since the first electric washing machine was produced in the early 1900's. Appliance industry has tried to obtain the performance of washing machine with large capacity, high energy efficiency, low vibration and low noise levels. As the installation peace of a washer becomes closer to the living space, vibration and noise problems become more important challenges. In general, a washing machine has four legs to support its body. Four legs of the washing machine should be attached on a floor. If not so, it may cause severe vibration or walking in the spin-drying process. Unfortunately, the floor of an ordinary house is bumpy in general, and the consumers will not accept bolting washing machines to a foundation; moreover, sometimes they move the location of their washing machines to utility rooms or bath rooms or kitchens and don't care for leveling the legs exactly. In this study, we devise an auto-leg system that prevents the occurrence of abnormal vibration and walking of washing machines. It is simply composed of a spring and a friction damper. Some experiments are implemented to show the dynamic characteristics of the three-dimensional auto-legged washing machine model that is located on the even or uneven ground. A spring parameter is optimized to adjust the length of the auto-leg system automatically up to 10 mm irregularity, and the friction damper is designed to decrease a resonance induced by the spring of the auto-leg system. Some numerical results show that placing the proposed auto-leg system in a washing machine makes good performance with low vibration, as well as low noise, regardless of the unevenness of the floor.

• 한국강구조학회 논문집
• /
• 제9권2호통권31호
• /
• pp.171-179
• /
• 1997

고장력 볼트 이음부에서의 힘의 전달은 부재간의 압축력 및 볼트축력에 의하여 외력과 균형을 이룸으로서 형성되어지며, 부재간의 압축력, 도입된 축력의 변화 및 미끄러짐하중 등은 볼트 체결부 및 볼트의 유효강성에 지배된다. 이때 유효강성은 일반적으로 접합부의 유효단면적과 탄성계수의 곱으로 나타내어지지만 접합부재의 유효단면적이 어느 정도가 되는지는 판단하기가 쉽지가 않다. 이를 위해서 종래에는 이음부의 탄성변형에 관계하는 유효단면적을 등가중공원통형으로 가정하여 이에 대한 여러 가지 검토가 이루어졌다. 그러나 이러한 제안식들은 설계상의 목적과 복잡한 계산을 피하기 위하여 매우 단순화시킨 것으로 어느 식이 타당한 지는 단정하기가 어려우며 이에 대한 상세한 해석적인 검토 및 실험적인 검증이 요구된다. 따라서, 본 연구에서는 볼트 축력에 의한 접합부재의 유효단면적 산정과 이에 대한 검증을 위하여 고장력 볼트 이음 시험편에 대해 피로시험을 실시하고 반복하중 재하 후의 마찰면의 형상을 관찰하여 유효마찰 영역을 측정하였으며, 유한 요소법에 의해 수치 해석을 실시하여 내부 압축응력의 분포형상을 밝히고 접촉면상에 발생하는 응력 분포영역을 근사화하므로서 마찰면의 형상과 내부 압축응력의 분포영역과의 관계 그리고 유효단면적의 산정 방법을 고찰하였다.

• 한국의류학회지
• /
• 제30권5호
• /
• pp.753-761
• /
• 2006

This paper suggests the optimal conditions for the laundry to prevent from the electrostatic charge by the evaluation of the electrostatic characteristics in the full process of washing and drying. Cotton, nylon, and polyester fabrics were used as test washing specimens. Detergent and softener were used under the standard washing cycle, and then the electrostatic characteristics of laundry were measured. The results showed that the moisture regain decreased and the electrostatic charge increased with the drying time. It was observed that the specimen fabrics were already dried up before the standard drying cycle was finished. Consequently, the excessive drying caused a generation of electrostatic charge due to the removal of the trace of moisture remaining and the excessive friction. Especially, the softener played an important role to prevent from a generation of electrostatic charge, whose insertion was more effective in the drying than in the rinsing process. It was also shown that the electrostatic charge could be decreased by drying the fabrics of one kind. On the other hand, for drying the mixed kinds of fabrics, the electrostatic charge increased remarkably. Therefore we suggest that the laundry be classified according to the kinds of fiber, and then be washed and dried before excessive drying to reduce electrostatic charge And further, a proper use of softener is effective to reduce electrostatic charge.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1027-1033
• /
• 2011

VCM 강판은 용융아연도금강판 위에 PET/PVC 코팅하여 가전제품의 외판 소재로 사용되고 있다. 본 연구에서는 VCM 강판의 프레스 성형 중 발생하는 PET 코팅층의 찢김을 저감하기 위해 프레스 성형공정변수를 재설계하였다. 프레스 공정변수들이 PET 코팅층의 찢김에 미치는 영향을 분석하기 위해 유한요소해석을 수행하였다. PET 코팅의 찢김 현상은 드로잉 성형시 제품의 코너부 소재두께의 증가로 인해 금형과 소재 사이의 과도한 마찰에 의해 발생한다. 이를 해결하기 위해 블랭크 형상의 변경을 통해 드로잉성형시 코너부의 소재두께 증가를 저감하였으며, 트리밍 공정시 플랜지부의 과도한 두께 증가부분을 제거하여 플랜지 성형시 소재두께가 금형간극 이하로 분포하도록 하였다. 또한 성형실험과 유한요소해석을 통해 재설계된 공정변수들을 검증하였다. 이를 통해 PET 코팅의 찢김이 없는 양호한 최종제품의 성형이 가능함을 확인하였다.