• Journal of Welding and Joining
• /
• v.19 no.6
• /
• pp.608-613
• /
• 2001

In this study, the rotary bending fatigue test was carried out with two kinds of base metal, martensite stainless steel STR3 and austenite stainless steel STR35 and the dissimilar friction welded material with them. To compare the fatigue fifes according to the notch positions, the small circular defect was worked on the bonded line, 1.0mm and 0.5mm distance form the bonded line. The fatigue limits of the STR3 and STR35 base metal were 429.0MPa and 409.4MPa respectably. In comparison with fatigue life at the same notch positions, the STR35 specimens showed about 190% for base metal, 82% for 1.0mm distance notched specimens higher than that of the STR3. But the fatigue life of the 0.5mm distance notched STR35 specimen showed about 35% lower than that of the STR3 specimen. And the bonded line notched specimen was much lower fatigue life than the other specimens because of separation of the bonded line.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.672-677
• /
• 2000

This paper compares the two kinds of friction model. The first model is classical stick/slip model. In the stick/slip model, the system is treated to have two different states, namely, stick state or slip state. The second one is continuous model developed by Dahl et. al, namely, Extended Dahl's model. Each model has unique properties, and can be best useful when it is applied on the appropriate system. In this paper, each model is applied on the simple two-block system and the complex automatic transmission system. And the simulation result including simulation accuracy and time required are compared.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1215-1220
• /
• 2008

The aim of this paper is to perform a finite element analysis that will have the ability to predict the seal performance characteristics, such as deformation, contact load and friction and also is to provide a means of potential seal designs, which can reduce the time and cost of designing the performance of the seal. The material property tests of elastomer seal are performed to obtain the hyperelastic properties and The Mooney-Rivlin constants are determined from these test results. A 2D modelling of the seal cross section is performed to simulate the contact behavior between the seal on the piston and the cylinder bore under operation conditions. The deformation behavior, contact load and friction of an elastomer seal is analyzed by a finite element method which performs three analytic phases of interference fit, the variations of pneumatic pressure and piston movement under the operational conditions.

• Textile Coloration and Finishing
• /
• v.22 no.3
• /
• pp.264-271
• /
• 2010

The purpose of this study was to investigate performance evaluation of absorbing and fast-drying fabric after washing. In the comparison of absorption and fast-drying properties, there was slight difference among the materials depending on thickness, weight, and fabric structure. Absorption speed of the materials depended on the frequency of washing which might be caused by modification of fabric structure or composition fiber due to friction during washing. The ability of fast-drying of the materials was gradually decreased with the increase of washing frequency, which might be caused by fatigue accumulation on inner fiber and structural change or destruction with friction during washing.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.5 s.98
• /
• pp.145-150
• /
• 1999

We have studied on the tribological characteristics of surface modification by Arc Ion Implantation(AIP) coating method. Coating materials were deposited by the Titanium carbide(TiC) and Titanium nitride(TiN). An experimental process was established to determine the tribological characteristics of friction and wear behaviour with the variation of applied load, temperature and the time by the Falex friction and wear test machine. The results, It can be improved that when the surface modification of hard coatings(TiC, TiN) was deposited steel, the tribological characteristics become better. It is argued that improved because of excellence of the anti-wear, the extreme pressure properties and the heat stability.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.185-190
• /
• 2003

Synchronizer ring performance is strictly required in order to extend manual transmission oil drain interval. Zn type additive, which is used as dispersant and anti-wear additive instead of SP additives in manual transmission oil, is applied to improve Synchronizing function and durability. But only Zn type additive is not suitable for high torque transmission because it has not good extreme pressure characteristics. We research on the synchronizer friction and extreme pressure properties in according to change additive types. As a result, it was found that the use of non-active extreme pressure and friction modifier additives has benefit in the improvement of synchronizer friction characteristics and durability.

• Tribology and Lubricants
• /
• v.15 no.2
• /
• pp.156-163
• /
• 1999

The mechanical characteristics of the high speed steel by Powder metallurgy Process (PM-HSS) has been reported to improve with several alloying constituents, such as high carbon, vanadium and cobalt. In this paper, sliding wear test has been conducted using a pin-on-disc machine for three PM-HSS which contains 0%, 5% and 12% cobalt respectively, in order to evaluate the effect of cobalt on wear properties of PM-HSS. The results of this study showed that the wear resistance of PM-HSS has been increased by the addition of cobalt on the range of experimental friction velocities. When compared with the effect of addition of cobalt, the wear resistance of PM-HSS with 5% cobalt has been found to be superior to that of PM-HSS with 12% cobalt.

• Journal of Welding and Joining
• /
• v.3 no.2
• /
• pp.1-9
• /
• 1985

In this study, the influence of carbon equivalents on friction welds of similar steels was investigated. Four types of steels with 15mm diameter tested in the wide range of carbon equivalents from 0.3 to 1.1 Main experimental results are summarized as follows : (1) Under the constant burn-off length, the friction time becomes longer with the increasing carbon equivalent, but the upset length shows no consistent tendencies. (2) Due to the recrystallization in the contact area, the maximum hardness occurs some away from the contact surface. And it increases almost linearly with the increasing carbon equivalent. (3) Even a steel with 1.1 C.E. can be friction welded to make defect-free welds. (4) With the increasing carbon equivalent, the bend angle and charpy impact value decrease very rapidly in the range from 0.3 C. E., but remain nearly unchanged for C. E. higher than 0.6. (5) Heat treatment of the base metals before welding has very little influence on the mechanical properties of welds. On the other hand, normalizing of the welds improves the bend angle and charpy impact value, but its effect becomes almost negligible, when the carbon equivalents are higher than 0.6.

• Journal of Welding and Joining
• /
• v.24 no.1
• /
• pp.50-55
• /
• 2006

In an attempt to optimize friction spot joining process of Al alloys for automobiles, effects of joining parameters such as tool rotating speed, plunging depth, and joining time on the joints properties were investigated. A wide range of joining conditions could be applied to join Al alloys for automobile without defects in the weld zone except for certain welding conditions with a lower heat input. For sound joints without defects, tensile shear strength of joints was higher than acceptable criteria of tensile shear strength of resistance spot welded joints for aluminum.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.384-386
• /
• 2005

Initial oxide layer on the butt surface fragments during friction stir welding (FSW) and then often remains as a faint zigzag-line pattern on the cross section. When remnant of the oxide layer often adversely affects the mechanical properties in the weld, it is called as 'kissing-bond'. The present study systematically examines effect of oxide array on bend property in the root of friction stir (FS) welded Al alloy 1050 by transmission electron microscopy (TEM), and then clarifies identity of the kissing-bond.