• 동력기계공학회지
• /
• 제17권4호
• /
• pp.64-71
• /
• 2013

In this paper, finite element method was used for flow and strength analysis of AZ31 magnesium alloy under friction stir welding. The simulations were carried out by SYSWELD s/w, and the modeling of sheet was doned by unigraphics NX3 s/w. Welding variables for analysis were rotating speed and welding speed of tool. Also two-way factorial design method was applied to confirm the effect of welding variables on maximum temperature and stress of material used. From these results, the increaser welding speed of tool the decreaser maximum temperature, but the increaser maximum stress. Also the increaser rotating speed of tool the increaser maximum temperature, but the decreaser maximum stress. In addition the increaser welding speed of tool and the decreaser rotating speed of tool, the narrower heat effect zone. Finally rotating speed of tool influenced on maximum temperature more than welding speed of tool, and welding speed of tool influenced on maximum stress more than rotating speed of tool from the variance analysis.

• 대한기계학회논문집A
• /
• 제21권6호
• /
• pp.884-895
• /
• 1997

The finite element analysis for the tubular alumina liner which was shrink-fitted into a heat treated high speed steel (HSS) sleeve and subjected to high inner pressure and high temperature was performed. The parameters for the analysis were the interference between the alumina and the HSS, the temperature, the inner pressure, the coefficient of friction between the alumina and the HSS, and the taper at the sleeve ends. From the analysis, it was found that the tensile hoop stresses were decreased when the end parts of the HSS sleeve were tapered and the tensile stresses were decreased as the coefficient of friction between the alumina and the HSS was decreased. Also it was found that the alumina might be used as the structural liner for high pressure and high temperature when it was shrink-fitted into a heat treated HSS sleeve.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.491-497
• /
• 2005

Brake system is indispensible functional part to the transportation machines such as railroad cars, and all of industrial machines. It is mechanical element to stop the movement or slow the speed, transforming kinetic energy of motion object into thermal energy through solid friction. According that recently the railroad cars have become high-speed, the technique in braking domain to secure the overall braking effort is making rapid progress. In particular, material development and manufacturing process are so important to secure friction performance, which is the core in braking performance of mechanical brake units. Wear of brake disk could mainly result in the diminishment of its life span due to thermal cracking, so the endurance against high temperature is required. On the other hand, in this case, the problem is that the side wear of pad, relative material is slightly increased because of enlargement of plastic deformation. It is necessary, therefore, to develop a disk material that will be used in the Tilting System mechanical brake units. The purpose of this paper is to make a study prior to developing brake disk of Tilting Train travelling at 200km/h and to propose the component of brake disk. Accordingly, I will conduct sufficient researches on technical documents of brake disk, that are basic documentations, analyze an impact on components, and further, considering braking degree of train, study for the basic proposal on brake disk's component of the train travelling at 200km/h, which has relatively minor influence of heat stress and maintains the friction. In this respect, I would like to investigate friction characteristics between disk and relative friction material via Test on some possible test segments, analyze and propose friction performance, temperature impact and so forth coming from the contact with pad, relative material to demonstrate the friction characteristics.

• 반도체디스플레이기술학회지
• /
• 제3권1호
• /
• pp.15-20
• /
• 2004

Through shallow trench isolation (STI) chemical mechanical polishing (CMP) tests, we investigated the dependence of pad surface temperature on the abrasive and additive concentrations in ceria slurry under varying pressure using blanket film wafers. The pad surface temperature after CMP increased with the abrasive concentration and decreased with the additive concentration in slurries for the constant down pressure. A possible mechanism is that the additive adsorbed on the film surfaces during polishing decreases the friction coefficient, hence the pad surface temperature gets lower with increasing the additive concentration. This difference in temperature was more remarkable for the higher concentration of abrasives. In addition, in-situ measurement of spindle motor was carried out during oxide and nitride polishing. The averaged motor current for oxide film was higher than that for nitride film, meaning the higher friction coefficient.

• 대한기계학회논문집B
• /
• 제26권8호
• /
• pp.1095-1101
• /
• 2002

An experimental apparatus was prepared to investigate thermal and hydrodynamic characteristics of regenerator at cryogenic temperature under pulsating pressure condition. The regenerator was pressurized and depressurized by a compressor with various operating frequencies. Cold end of the regenerator was maintained around 100 K by means of a liquid nitrogen heat exchanger. Instantaneous gas temperature and mass flow rate were measured at both ends of the regenerator during the whole pressure cycle. Pulsating pressure drop across the regenerator was also measured to see if it could be predicted by a friction factor at steady flow condition. The operating frequency of pressure cycle was varied between 3 and 60 Hz, which are typical operating frequencies of Gifford-McMahon, pulse tube, and Stilting cryocoolers. First, the measured friction factor for typical wire screen mesh regenerator was nearly same as steady flow friction factor for maximum oscillating Reynolds number up to 100 at less than 9 Hz. For 60 Hz operations, however, the discrepancy between oscillating flow friction factor and steady flow one was noticeable if Reynolds number was higher than 50. Second, the ineffectiveness of regenerator was directly calculated from experimental data when the cold-end was maintained around 100 K and the warm-end around 293 K, which simulates an actual operating condition of cryogenic regenerator. Influence of the operating frequency on ineffectiveness was discussed at low frequency range.

• Tribology and Lubricants
• /
• 제30권1호
• /
• pp.29-35
• /
• 2014

The temperature-dependent tribological properties of brake discs for a train were examined in this study. The discs were produced using heat-resistant alloy steel, which showed different thermal conductivity after the heat treatments. A commercial brake friction material was used to evaluate the friction effectiveness, and the friction tests were carried out using a 1/5 scale dynamometer under various initial braking temperature conditions. The results showed that the tribological property of the disc was strongly affected by the heat treatment schedule. At low temperatures (below $250^{\circ}C$), the friction coefficient increased as a function of disc temperature, indicating that frictional heat increased the adhesion between the disc and pad. In addition, fade was observed at high temperatures (above $250^{\circ}C$); it was pronounced in the case of the disc with low thermal conductivity. The different fade resistances observed in the discs with different heat treatment schedules appear to be influenced by microstructural changes such as carbide redistribution occurring during the heat treatments, which affected the thermal conductivity.

• 한국산학기술학회논문지
• /
• 제17권7호
• /
• pp.434-441
• /
• 2016

마찰교반용접은 소재와 용접 툴 간의 마찰열에 의해 접합되는 고상접합 공정이다. 용접 시 발생하는 입열량에 따라 용접부의 건전성이 결정된다. 과도한 입열량은 산화물 및 기공결함의 원인이 되며, 불충분한 입열량은 터널결함 등의 문제점이 발생한다. 따라서 마찰교반용접부 중심에서의 온도 이력을 파악하는 것은 건전성을 판단하는 데 있어 매우 중요한 연구이다. 본 연구에서는 마그네슘 합금소재에 대한 마찰교반용접부의 온도분포 특성을 평가하였다. 이를 위해 유한요소해석을 통한 마찰교반용접부의 유동장 및 온도분포를 예측하였다. 유한요소해석을 위해 용접 툴 형상 간소화, 마찰 조건 선정 등 선행 해석을 수행하고 최적조건을 도출하였다. 또한, 해석모델의 검증을 위해 마그네슘 합금의 맞대기 마찰교반용접 시 용접부 중앙에서의 온도를 측정하였다. 유한요소해석 결과 마찰교반용접부의 온도에 영향을 미치는 주요변수의 기여도는 회전속도가 이송속도보다 더 높은 것으로 판단된다. 또한, 용접부 중심에서의 실측 온도와 유한요소해석 결과 사이에 5.4% - 7.7% 수준의 오차 내에서 잘 일치하였다.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.15-22
• /
• 2017

Because the running speed of vehicles is increasing and a shorter braking distance is required, high heat-resistant brake pads are needed to satisfy the requirements of customers and car makers. In the near future, hazardous materials such as Cu, Cr, Zn, and Sb will be restricted from use in friction materials. Ceramic composites reinforced by carbon fibers are good candidates for eco-friendly friction materials. In this study, we develop ceramic composite friction materials. The friction materials are composed of carbon fibers, Si, SiC, graphite, and phenol resin and are prepared by hot forming and heat treatment at high temperatures. The density, void ratio, and compressive strength are $1.59-1.66g/cm^3$, 16.6-20, and 70-90 MPa, respectively. Friction and wear tests are performed using a pin-on-plate-type reciprocating friction tester at 25, 100, and $200^{\circ}C$. The counterpart material is a CrMoV steel extracted from a KTX brake disc. Friction coefficient, wear amount, and wear mechanism are measured and examined. We determine that the friction coefficients depend on the temperature and the fluctuation of the friction coefficients is larger at higher temperatures. The amount of wear increases with the surface temperatures of the specimens. The tribological properties of the developed composites are similar to those of a Cu-based sintered friction material. Through this study, it is confirmed that ceramic composite materials can be used as friction materials.

• 한국기계가공학회지
• /
• 제7권3호
• /
• pp.110-114
• /
• 2008

In this study, to examine the friction coefficient and wear amount of dental prosthesis, pin-on-disk type wear test were at room temperature. Vickers hardness and fracture toughness measurement of dental materials were preformed. Microscopic observations on worn surfaces of specimens were conducted by SEM. The friction coefficient of dental material was investigated according to weight and slinging velocity. dental material have investigated composed to nature teeth.

• Tribology and Lubricants
• /
• 제24권1호
• /
• pp.44-48
• /
• 2008

The wear characteristics of the gold alloy dental prosthesis have been investigated. The wear tests were performed by using a pin-on-disk wear tester at room temperature. Vickers hardness and fracture toughness measurement of dental materials were preformed. Microscopic observations on worn surfaces of specimens were conducted by microscope. The friction coefficient of the gold alloy dental prosthesis was investigated according to weight and slinging velocity. The hardness of the gold alloy dental prosthesis were similar and a half of the enamel of natural teeth.