• Journal of Environmental Science International
• /
• v.14 no.1
• /
• pp.61-69
• /
• 2005

Adsorption characteristics of toluene vapor, which is one of important source of volatile organic compounds (VOCs), by activated carbon were investigated using a fixed bed adsorption column. The operating parameters such as breakthrough curve, adsorption capacity, mass transfer zone (MTZ), and length of unused bed (LUB) were studied. The experimental results showed that the breakthrough time decreased with increasing inlet toluene concentration and gas flow rate. MTZ and LUB increased with the increase of inlet concentration, gas flow rate, and particle size of activated carbon. The adsorption capacity increased with the increase of inlet toluene concentration, while it decreased with increasing particle size. However, it was kept at constant value regardless of the increase of gas flow rate. Adsorption isotherm of toluene vapor could be represented by the Freundlich adsorption equation fairly well. From the adsorption experiments using some VOC gases such as toluene, xylene, butyl acetate. butanol and acetone, it was also found that the adsorption capacity was higher in the case of gas with higher boiling point and lower vapor pressure.

• Applied Chemistry for Engineering
• /
• v.27 no.3
• /
• pp.265-269
• /
• 2016

Ammonia gas as a hydrogen source has received great attention since the importance of hydrogen gas as a clean energy source increased. However, ammonia is toxic and corrosive to metal such that the absorbent that can store and transport ammonia became an important issue. As an effort to solve this, a large pored covalent organic framework, COF-10 was proposed as an adsorbent for storage and safe transportation of ammonia. During the ammonia adsorption process, boron in COF-10 structure can act as a Lewis acid site and bind with ammonia. In this study, COF was synthesized and its structure was identified by BET, XRD and FT-IR. The adsorption characteristics of COF were investigated by TPD and adsorption isotherm. The COF-10 showed an excellent adsorption capacity for ammonia (9.79 mmol/g) which could be utilized as an ammonia adsorbent.

• Advances in environmental research
• /
• v.8 no.1
• /
• pp.23-38
• /
• 2019

In this study, Malachite Green (MG) dye removal from synthetic wastewaters by adsorption process using raw boron enrichment waste (BEW) and it's modifications (with acid and ultrasound) were aimed. 81% MG removal was obtained by BEW at optimum equilibrium conditions (time: 40 min., dosage: 500 mg/dm³, pH: 5-6, speed: 200 rpm, 298 K). MG removal from wastewaters using acid modified boron enrichment waste (HBEW) was determined as 82% at optimum conditions (time: 20 min., dosage: 200 mg/dm³, pH: 10, speed: 200 rpm, 298 K). For ultrasound modified BEW (UBEW), the highest MG removal percent was achieved as 84% at optimum conditions (time: 30 min, dosage: 375 mg/ dm³, pH: 8, speed: 200 rpm, 298 K). The equilibrium data of Malachite Green was evaluated for BEW, HBEW and UBEW adsorbents by using sorption isotherms such as Langmuir, Freundlich and Temkin models, out of which Langmuir model (R² = 0.971, 0.987 and 0.984) gave better correlation and maximum adsorption capacity was found to be 147.05, 434.78 and 192.30 mg/g, respectively. The adsorption kinetics followed the pseudo-second-order kinetic equation for sorption of MG onto wastes. A look at thermodynamic data reveals that natural sorption is spontaneous and endothermic because of free negative energy exchange and positive change in enthalpy, respectively. The results indicated that boron enrichment waste, and HCl and ultrasound-modified boron enrichment waste served as good alternative adsorbents in dye removal from wastewater.

• Korean Journal of Materials Research
• /
• v.27 no.3
• /
• pp.166-171
• /
• 2017

Removal of phosphate from environmental water has become more important to prevent eutrophication. In the present study, sorption behavior of phosphate onto magnesite was investigated under different conditions. The optimum pH of phosphate adsorption was determined to be 6.0. The adsorption capacity was found to decrease with increasing temperature, which indicates that a low temperature was beneficial for phosphate adsorption. The sorption capacity for phosphate was found to be 10.2 mg/g at an initial concentration of 100 mg/L and a dose of 2 g/L. The first order kinetic equation and Freundlich isotherm model fit the data well. Phosphate adsorption on magnesite was explained by electrostatic attraction and weak physical interactions.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.2
• /
• pp.218-229
• /
• 2011

Dyeing properties of cotton and ramie fabrics with pine needles colorants were studied by investigating the analysis of pine needles colorants, the effect of dyeing conditions (such as dye concentration, dyeing temperatures and times on dye uptakes), effect of mordants, and color change. The various colorfastness of dyed fabrics were evaluated for practical use; in addition, the antimicrobial ability, ultraviolet-cut ability, and deodorant ability were estimated. In the UV-Visible spectrum, the wavelength of the maximum absorption for pine needles extract was 285nm, and pine needles colorants produced a yellow color. From FT-IR and GC-MS results, it was assumed that chromophoric substance from pine needles extracts were mixed with flavonol tannin and flavanol tannin. An increased dyeing concentration resulted in a larger dye uptake and a Freundlich absorption isotherm was obtained. A larger dye uptake occurred as the dyeing time and temperature increased. Post-mordanting was more effective than pre-mordanting and the dye uptake of fabrics improved by mordanting. The colorfastness of dyed fabrics showed a low rating; however, colorfastness to washing and dry cleaning of cotton fabrics mordanted with N.Cu, and friction fastness of ramie fabric mordanted with Cu improved. The dyed fabrics showed very good antimicrobial abilities of 99.9%. In addition, the ultraviolet-cut ability and deodorant ability improved in fabrics dyed with pine needles extracts.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.2
• /
• pp.206-217
• /
• 2011

The dyeing properties of cotton fabrics with bamboo colorants were studied by investigating the analysis of bamboo colorants, the effect of dyeing conditions (dye concentrations, dyeing temperatures and times on dye uptakes), effect of mordants, and color change. The various colorfastness of dyed fabrics were evaluated for practical use; in addition, the antimicrobial ability, ultraviolet-cut ability, and deodorant ability were also estimated. In the UV-Visible spectrum, the wavelength of the maximum absorption for bamboo stems and leaves extracts was found to be 280nm and 295nm, respectively; in addition, bamboo colorants produced a yellow color. From the FT-IR and GC-MS results, it was assumed that the chromophoric substance from bamboo extracts was composed of flavones substances with tricin. An increased dyeing concentration resulted in a larger dye uptake and a Freundlich absorption isotherm was obtained. A larger dye uptake occurred as the dyeing time and temperature increased. The post-mordanting was more effective than pre-mordanting. Mordants, Fe and N.Fe, were effective for an increased dye uptake. The color of fabrics mordanted with Cu and N.Cu changed to GY. Regardless of mordanting, the colorfastness on the washing of dyed fabrics showed a low rating compared to other fastness. Mordanting adversely affected the lightfastness of dyed fabric. The dyed fabric showed very good antimicrobial abilities of 99.9%. In addition, the ultraviolet-cut ability and deodorant ability improved in cotton fabric dyed with bamboo extracts.

• Korean Chemical Engineering Research
• /
• v.48 no.6
• /
• pp.784-790
• /
• 2010

VOCs such as acetone, benzene, toluene, ethylbenzene were adsorbed in a fixed-bed adsorber using zeolite synthesized from coal fly ash and 4 kinds of activated carbon at 101.3 kPa. The adsorber was operated batchwise with the charge of 5 g adsorbent to obtain the breakthrough curve of VOCs. Experiments were carried out at $40^{\circ}C$, nitrogen flow rate of $70cm^3/min$ and sparger temperature of $30^{\circ}C$. The deactivation model was tested for these curves by combining the adsorption of VOCs and the deactivation of adsorbent particles. The observed values of the adsorption rate constant and the deactivation rate constant were evaluated through analysis of the experimental breakthrough data using a nonlinear least square technique. The experimental breakthrough data were fitted very well to the deactivation model than the adsorption isotherm models in the literature. Also, adsorption capacities of adsorbents were obtained from the breakthrough curve to observe the correlation between adsorption capacity and the physical properties of VOCs.

• Nuclear Engineering and Technology
• /
• v.28 no.1
• /
• pp.44-55
• /
• 1996

For the purpose of controlling the release of radioiodine to the environment in nuclear power plants, adsorption characteristics of elemental iodine and methyl iodide on the base carbon and 2%, 5% TEDA impregnated carbons were studied. The amounts of adsorption of elemental iodine and methyl iodide on the carbons were compared with Langmuir, Freundlich, Sips and Dubinin-Astakhov(DA) isotherm equations. Adsorption data were well correlated by the DA equation based on the potential theory. Adsorption energy distributions were obtained from the parameters of the DA equation derived from the condensation approach method. For the adsorption of methyl iodide and elemental iodine-carbon system, the DA equation can be well expressed by the degree of heterogeneity of the micropore system because the surface is nonuniform when its potential energy is unequal. The adsorption energy distribution wes investigated to find a surface heterogeneity on the carbon. The surface heterogeneity for iodine-carbon system is highly affected by the adsorbate-adsorbent interaction as well as the pore structure. The surface heterogeneity increases as a content of TEDA impregnated increases. The adsorption nature of methyl iodide on carbon turned out to be more heterogeneous than that of elemental iodine.

• Journal of Industrial Technology
• /
• v.27 no.A
• /
• pp.195-202
• /
• 2007

Milled Korean pine (Pinus densiflora) wood was used to evaluate its adsorption capacity of Cu(II) ions from aqueous solution by running a series of batch experiments. Prior to the tests, the milled woods were pretreated with 1N NaOH, 1N $HNO_3$, and distilled water, respectively, to examine the effect of pretreatment. Within the tested pH range between 3 and 6, copper adsorption efficiency of NaOH-treated wood(96~99%) was superior to the $HNO_3$-treated wood(19~31%) and distilled water-treated wood(18~35%). The efficiency of copper removal by wood enhanced with increasing solution pH and reached a maximum copper ion uptake at pH 5~6. Adsorption behavior of copper onto both raw and $HNO_3$-treated woods was mainly attributed to interaction with carboxylic acid group. For NaOH-treated wood, carboxylate ion produced by hydrolysis or saponification was a major functional group responsible for Cu sorption. NaOH treatment of wood changed the ester and carboxylic acid groups into carboxylate group, whereas $HNO_3$ treatment did not affect the production of functional groups which could bind copper. A pseudo second-order kinetic model fitted well for the sorption of copper ion onto NaOH-treated wood. A batch isotherm test using NaOH-treated wood showed that equilibrium sorption data were better represented by the Langmuir model than the Freundlich model.

• Journal of Environmental Health Sciences
• /
• v.34 no.3
• /
• pp.240-246
• /
• 2008

The purpose of this study was to gain basic information on the characteristics of $CO_2$ adsorption in relation to $Na_2CO_3$, $K_2CO_3$, $Li_2CO_3$-impregnated activated carbon in a Fixed Bed Reactor. From the results of this study the following conclusions were made: $Na_2CO_3$, $K_2CO_3$, $Li_2CO_3$-impregnated activated carbon had a longer breakthrough time and more enhanced adsorption capacity than activated carbon alone. When tested with isothermal adsorption and tested for $CO_2$ adsorption the amount of $CO_2$ adsorbed varied with temperature, $CO_2$ inlet concentration, gas flow rate, aspect ratio, etc. Based on the results, when Langmuir, Freundlich and Dubinin-Polanyi adsorption isotherms were used for linear regression of isothermal adsorption data, Langmuir adsorption isotherm was the most suitable. And, the optimum condition for $Na_2CO_3$ and $K_2CO_3$ impregnated activated carbon make-up was 1N and $Li_2CO_3$ was 0.1N. It could be concluded that adsorption capacity was decreased with adsorption temperature and increased gas concentration. When the aspect ratio (L/D) was varied 0.5, 1.0 and 2.0, the significant drop of adsorption amount was observed below 1.0 and breakthrough time was shortened with gas flow rate.