• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.492-501
• /
• 2013

In this paper, a multi polarization reconfigurable microstrip antenna that can be used selectively for four polarizations(vertical polarization, horizontal polarization, right hand circular polarization, left hand circular polarization) at the S-band is presented. The proposed antenna consists of four PIN diodes and a microstrip patch with a cross slot and a circular slot and is fed by utiliting electromagnetic coupling between the microstrip patch and the feed line. The proposed antenna has a DC bias network to supply DC voltage to each PIN diode and the polarization can be determined by controlling the ON /OFF states of four PIN diodes. The fabricated antenna has a VSWR below 2 in the vertical polarization(3.17~3.21 GHz), the horizontal polarization(3.16~3.20 GHz), the left hand circular polarization (3.08~3.19 GHz), and the right hand circular polarization(3.10~3.2 GHz) frequency bands. The designed antenna has the cross polarization level higher than 20 dB, a gain over 5 dBi for the linear polarization states, and 3 dB axial ratio bandwidth wider than 50 MHz in the circular polarization states.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.111-117
• /
• 2006

Reconfigurable CMOS low-noise amplifier (LAN) has been developed for multi-mode/multi-band wireless receiver. By employing common-gate input stage, the performance can be optimized for multiple operation bands by simply controlling the output load impedance. Although the conventional common-gate LAN has larger than 3dB noise figure (NF), the newly developed negative feedback scheme enables the common-gate input LNA to have less than 2dB NF. To have optimum linearity performance of wireless receiver, the gain of the LNA can be controlled. The LNA implemented in a 0.13mm CMOS technology shows $19{\sim}20dB$ voltage gain, $1.7{\sim}2.0dB$ NF, -2dBm iIP3 at $1.8{\sim}2.5GHz$ frequency range. The LNA dissipates 7mW from a 1.2V supply voltage.

• Journal of Navigation and Port Research
• /
• v.28 no.5
• /
• pp.429-434
• /
• 2004

In this paper, we designed a reconfigurable slot antenna using sequentially voltage-applied RF MEMS switches. In order to obtain pull-in voltage and maximum stress of the MEMS switches, the switch structures in accordance with airgap height was analyzed by ANSYS simulation A actuation voltage of MEMS switches can be determined by switch geometry and airgap height between a movable plate and a bottom plate. The designed lengths of MEMS switches were 240 $\mu\textrm{m}$, 320 $\mu\textrm{m}$, 400 $\mu\textrm{m}$, respectively and the airgap was 6$\mu\textrm{m}$. The total size of the designed slot antenna was 10 mm x 10 mm and the slot length and width were 500 $\mu\textrm{m}$ and 200 $\mu\textrm{m}$, respectively. The length and size of the CPW feedline were 5 mm and 30-80-30 $\mu\textrm{m}$, respectively. and then the size of the CPW in the slot was 50-300-150 $\mu\textrm{m}$. The tuning of the resonant frequency of the proposed device is realized by varying the electrical length of the antenna, which is controlled by applying the DC bias voltages to the RF MEMS switches. The designed slot antenna has been simulated, fabricated and measured.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4125-4130
• /
• 2015

This paper presents the communication performance for the radiation pattern reconfigurable antenna in the wearable device measuring bio signal (temperature, blood pressure, pulse etc.) of human body. The operational frequency is 2.4 - 2.5 GHz, which covers Bluetooth communication bandwidth. The maximum gain of the antennas is 1.96 dBi. The proposed antenna is efficiently transmitting and receiving signal by generating two opposite beam directions using two RF switches (PIN diode). Also, we investigated how radiation pattern changes according to three angles ($30^{\circ}$, $90^{\circ}$, $150^{\circ}$) of Top Loading. In this paper, we measured and compared the SNR (Signal-to-Noise Ratio) and BER (Bit Error Rate) performances of the proposed antennas in the condition between an ideal environment of anechoic chamber and smart house existing practical electromagnetic interferences (Universal Software Radio Peripheral, USRP). Throughout the comparing the results of the measurement of two cases, we found that the SNR is degraded over 5dB in average and BER is increased over ten times in maximum, therefore, it is confirmed that the error rate of receiving signal is increased. The measured results of SNR and BER value in this paper able to expect the performance degrading by the interference from the electromagnetic devices.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.719-722
• /
• 2005

The synthesis of the 3D images is the most important part of the virtual reality. The photon mapping is the best method for reality in the 3D graphics. This paper presents an architecture for photon mapping applications on SOC devices. The proposed architecture reduces the computation time to photonmap search and radiance estimation. Also this architecture is implemented by a SIMD processor which trades parallelism for frequency of operation.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.318-320
• /
• 2009

A switchable Yagi-Uda antenna prototype with radiation pattern reconfiguration is presented in this letter. The proposed reconfigurable antenna is based on the concept of switching between the reflector and director of a Yagi-Uda antenna using a radio frequency PIN diode. As a result, the minimum/maximum radiation can be steered towards desired signals or away from interfering signals in opposite directions. The measured 10 dB impedance bandwidth and gain are 210 MHz (7%) and 8.02 dBi at 3 GHz, respectively. Details of the antenna design and its performance are described and empirically analyzed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.9
• /
• pp.1652-1659
• /
• 2008

With the increase of huge amount of data in network systems, ultimate high-speed network has become an essential requirement. In such systems, the encryption and decryption process for security becomes a bottle-neck. For this reason, the need of hardware implementation is strongly emphasized. In this study, a mixed inner and outer round pipelining architecture is introduced to achieve high speed performance of ARIA hardware. Multiplexers are used to control the lengths of rounds for 3 types of keys. Merging of encryption module and key initialization module increases the area efficiency. The proposed hardware architecture is implemented on reconfigurable hardware, Xilinx Virtex2-pro. The hardware architecture in this study shows that the area occupied 6437 slices and 128 BRAMs, and it is translated to throughput of 24.6Gbit/s with a maximum clock frequency of 192.9MHz.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2005.11a
• /
• pp.1195-1198
• /
• 2005

Radio Frequency Identification(RFID)를 이용한 물류 시스템은 바코드를 대체할 시스템으로 주목받고 있다. 이러한 RFID 를 이용한 물류 시스템이 실제로 적용하는 데에는 매우 큰 설치 비용이 문제로 제기된다. 이를 해결하기 위해 무선으로 연결되는 이동형 RFID 리더를 이용한다. 한편 동기화 모드 및 비동기화 모드로 전송되는 RFID 데이터의 특성과 기존의 라우팅 기법의 브로드캐스트에 따른 오버헤드를 줄이기 위해 재구성 가능한 클러스터 기반의 라우팅 기법이 적합하다. 따라서 RFID 창고 관리 시스템을 위한 재구성 가능한 클러스터 기반의 라우팅 기법을 제안한다.

• Journal of the Optical Society of Korea
• /
• v.1 no.1
• /
• pp.52-59
• /
• 1997

In this paper, we propose a system design for a parallel3-dimensional optical interconnection network utilizing variable grating mode liquid crystal devices (VGM LCD's) which are optical transducers capable of performing intensity-to-spatial-frequency conversion. The proposed system performs real-time, reconfigurable, but blocking and nonbroadcasting 3-dimensional optical interconnections. The operating principles of the 3-D optical interconnection network are described, and some of the fundamental limitations are addressed. The system presented in this paper can be directly used as a configuration of switching elements for the 2-D optical perfect-shuffle dynamic interconnection network, as well as for a B-ISDN photonic switching system.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.1
• /
• pp.151-155
• /
• 2010

Reconfigurable radio technology is needed to reconstruct frequency and modem functionality, which can be different in various regions. In addition, it makes a single mobile handset capable of supporting various standards of wireless communication and thus plays a key role in mobile convergence. An MMIC VCO (voltage controlled oscillator) has been developed for high power and wide bandwidth where Clapp-Gouriet type oscillators are adapted for series feedback, and was fabricated based on 0.15um pHEMT of TRW. The MMIC VCO was connected to an aluminar substrate on the carrier for testing. This MMIC VCO module showed good performance in comparison to existing works. Furthermore, it can be potentially extended to reconfigure an MMIC VCO for wireless systems such as military applications and satellite communications.