• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1062-1065
• /
• 2002

We demonstrate the MMIC(monolithic microwave integrated circuit) frequency doublers generating stable and low-cost 29 ㎓ local oscillator signals from 14.5 ㎓ input signals. These devices were designed and fabricated by using the MMIC integration process of 0.1 $\mu\textrm{m}$ gate-length PHEMTs (pseudomorphic high electron mobility transistors). The measurements showed S$\_$11/ of -9.2 dB at 14.5 ㎓, S/sub22/ of -18.6 dB at 29 ㎓ and a minimum conversion loss of 18.2 dB at 14.5 ㎓ with an input power of 6 dBm. The fundamental signal of 14.5㎓ was suppressed below 15.2 dBc compared with the second harmonic signal at the output port, and the isolation characteristics of the fundamental signal between the input and the output port were maintained above 30 dB in the frequency range of 10.5 ㎓ to 18.5 ㎓.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.12A
• /
• pp.1019-1024
• /
• 2003

In the thesis, we propose a new type of the predistortion linearizer using frequency multiplier The linearizer utilizing the 2nd and 3th harmonic used the individual control of the 3rd and 5th order intermodulation distortion(IMD) component. This structure is composed of wilkinson power combiner for combine and isolation of output signal, 3rd order IMD product controller using doubler and 5th order IMD product controller using tripler. The proposed predistortion linearizer controlled by individual order is obtained for about -16 dBc and 18 dBc of 3rd order and 5th order IMD components, respectively, over the frequency band 870 MHz to 880 MHz at the output power of 34 dBm/tone.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.6
• /
• pp.195-200
• /
• 2018

A W-band frequency octupler is implemented on 100-nm GaAs pHEMT process. The fabricated octupler can be used as a local oscillator or a signal source of W-band transceivers. Three common-source doublers are connected in cascade to multiply an input signal of 10.75 GHz to 83 GHz. A common-source amplifier is followed for each doubler to improve the conversion gain and suppress the unwanted harmonics. The fabricated octupler showes high output of more than 6 dBm in the 80 - 84 GHz band and achieved excellent spurious suppression performance over 20 dBc.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.368-371
• /
• 2020

In this paper, we propose a linear tapered slot rectifying antenna for a portable UHF-band RFID system. Since the proposed rectifying antenna does not use a dielectric substrate, the planar antenna is implemented with a thin metal thickness. The rectifier circuit converts input RF power into output DC voltage using a voltage doubler circuit based on two anti-parallel schottky diodes. The rectifying antenna is integrated by the voltage doubler circuit into a linear tapered slot antenna. For conjugate impedance matching of the rectifying circuit and the linear tapered slot antenna, the source-pull method was utilized by adjusting the angle of the tapered slot and the length of the antenna feed line. The proposed antenna prototype has been verified with the electrical and radiation characteristics through RF-DC conversion and far-field radiation test in open space measurement environment. Finally, the proposed antenna is realized to 0.23-wavelength (75 mm) and 0.18-wavelength (60 mm) at 915 MHz center frequency.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.3
• /
• pp.242-249
• /
• 2011

The proposed converter has easy device selection for high step-up and high power applications since boost half bridge and voltage doubler cells are connected, respectively, in parallel and series in order to increase output power and voltage. Especially, optimized design of high frequency transformers is possible owing to reduced turn ratio and eliminated dc offset, and distributed power through three cores is beneficial to low profile and thermal distribution. The proposed converter does not necessitate start-up circuit and additional clamp circuit due to the use of whole duty range between 0 and 1 and is suitable for applications with wide input voltage range. Also, high efficiency can be achieved since ZVS turn on of switches are achieved in wide duty cycle range and ZCS turn on and off of diodes are achieved. The proposed converter was validated through 5 kW prototype.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.980-982
• /
• 2002

In this paper, we report the experimental results of the Forward-flyback DC-DC converter with current doubler and synchronous rectifier. The experimental converter, that has a output voltage 1.8V, output current 25A, maximum power of 45W, switching frequency of 290kHz and input voltage range of 36-75V, has been successfully implemented. As a result, in the entire voltage range the measured full load efficiency was above 82%, and the output voltage was regulated at 1.8V within ${\pm}$3% tolerance.

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.132-134
• /
• 2006

This paper presents the design and implementation of 1 kW prototype DC-DC power converter with bridge voltage-doubler suitable for small scale PEM fuel cell system and its associated control scheme. The operation principle of this converter is described using some operating waveforms and the switching mode equivalent circuits based on simulation results and a detailed circuit operation analysis and soft-switching conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.523-526
• /
• 2001

In this paper, we design and fabricate the high-efficiency and low-power switched-capacitor DC-DC converter. This converter consists of internal oscillator, output driver and output switches. The internal oscillator has 100kHz oscillation frequency and the output switches composed of one pMOS transistor and three nMOS transistors. According to the configuration of two external capacitors, the converter has three functions that are the Inverter, Doubler and Divider. The proposed converter is fabricated through the 0.8$\mu\textrm{m}$ 2-poly, 2-metal CMOS process. The simulation and experimental result for fabricated IC show that the proposed converter has the voltage conversion efficiency of 98% and power efficiency more than 95%.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.528-532
• /
• 1987

Closed-loop fiber-optic gyroscope with linear scale factor for a wide dynamic range is demonstrated using a gating process and two-harmonic phase modulation, of which the second harmonic is obtained by a frequency doubler. Also the effects of the second harmonic and duty cycle of gating signal on the linearity of scale factor are estimated theoretically and compared with the measured data. The experimental results show the best linearity of scale factor is about 0.5% within the rotation rate 90.deg./sec. The closed-loop fiber-optic gyroscope with gated two-harmonic phase modulation can be used in the application demanding less sensitive performance and modest scale factor linearity.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1999.11a
• /
• pp.95-98
• /
• 1999

This paper describes preliminary discussions on spatial distribution of NO density, which is mostly contained in simulated NOX exhaust, between a wire-cylinder geometry discharge gaps by using Laser Induced Fluorescence(LIF) Spectroscopy. Spatial distribution of NO density will be measured with varying NO concentrations from 166 to 644[ppm] and diameters of central electrode from 6 to 10mm. Pulsed Nd:YAG laser, Optical Parametric Oscillator(OPO), and Frequency Doubler are used to excite NO molecules to their excited state.