• Journal of Korean Foot and Ankle Society
• /
• v.7 no.2
• /
• pp.269-273
• /
• 2003

Although osteochondromas are common lesions, osteochondroma accompanying diastasis of the ankle joint in a child or adult is an uncommon condition. No previous cases of distal tibiofibular diastasis caused by an osteochondroma in adult have been reported except in child. The authurs experienced a case of mild distal tibiofibular diastasis secondary to an osteochondroma in a 37-year-old female presented with right ankle pain. Osteochondroma of the distal tibiofibular joint were detected on magnetic resonance imaging (MRI). She was pain-free 4 weeks after excision of the osteochondroma. The patient has remained asymptomatic for 1 years postoperatively. Early excision obviates the need for complex reconstructive surgery to correct ankle deformity later.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.2983-2985
• /
• 1999

This paper presents the attitude control of the double inverted pendulum with compliant joint. The biped robot with compliant ankle joint instead of a motor have a good contact between it's sole and ground in the uneven ground. The compliant ankle joint proposed here is composed of springs and mechanical constraint. The lower link is hinged on the plate to free for rotation in the vertical plate. The upper link is connected to the lower link through a DC motor. The DC motor is used to control the posture of the pendulum by adjusting the position of the upper link. The algorithm for controlling a proposed inverted pendulum is nonlinear feedback controller. Simulation with mathematical model are conducted to show the validity of the proposed controller.

• Journal of Welding and Joining
• /
• v.22 no.3
• /
• pp.56-61
• /
• 2004

Friction stir weldability of AZ31B Mg alloy was studied using microstructural observation and mechanical tests. Defect free joints was obtained under the condition of 2000rpm-100mm/min. In TMAZ, a lot of twin deformation were observed due to the mechanical effect of the FSW tool and thus relatively high hardness was obtained. In SZ, the twin deformation was disappeared by recovery and the hardness decreased because the. grain structure was coarsened by dynamic recrystallization and grain growth. The Al-Mn precipitates were observed throughout the joint regions. On the other hand, $$\beta$-Mg_{17}Al_{12}$ intermetallic compounds were not observed in either of the zone. The joint efficiency was about 80% and the impact value of the joint was almost equal to that of base metal.

• Structural Engineering and Mechanics
• /
• v.83 no.5
• /
• pp.693-707
• /
• 2022

Bonded joints have proven their performance against conventional joining processes such as welding, riveting and bolting. The single-lap joint is the most widely used to characterize adhesive joints in tensile-shear loadings. However, the high stress concentrations in the adhesive joint due to the non-linearity of the applied loads generate a bending moment in the joint, resulting in high stresses at the adhesive edges. Geometric optimization of the bonded joint to reduce this high stress concentration prompted various researchers to perform geometric modifications of the adhesive and adherends at their free edges. Modifying both edges of the adhesive (spew) and the adherends (bevel) has proven to be an effective solution to reduce stresses at both edges and improve stress transfer at the inner part of the adhesive layer. The majority of research aimed at improving the geometry of the plate and adhesive edges has not considered the effect of temperature and water absorption in evaluating the strength of the joint. The objective of this work is to analyze, by the finite element method, the stress distribution in an adhesive joint between two 2024-T3 aluminum plates. The effects of the adhesive fillet and adherend bevel on the bonded joint stresses were taken into account. On the other hand, degradation of the mechanical properties of the adhesive following its exposure to moisture and temperature was found. The results clearly showed that the modification of the edges of the adhesive and of the bonding agent have an important role in the durability of the bond. Although the modification of the adhesive and bonding edges significantly improves the joint strength, the simultaneous exposure of the joint to temperature and moisture generates high stress concentrations in the adhesive joint that, in most cases, can easily reach the failure point of the material even at low applied stresses.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.365-366
• /
• 2002

The sliding wear behavior of ultra high molecular weight polyethylene (UHMWPE) was examined on a novel low temperature degradation-free zirconia/alumina composite material and conventional alumina and zirconia ceramics used for femoral head in total hip joint replacement. The wear of UHMWPE pins against these ceramic disks was evaluated by performing linear reciprocal sliding and repeat pass rotational sliding tests for one million cycles in bovine serum. The weight loss of polyethylene against the novel low temperature degradation-free zirconia/alumina composite disks was much less than those against conventional ceramics for all tests. The mean weight loss of the polyethylene pins was more io the linear reciprocal sliding test than in the repeal pass rotational sliding lest for all kinds of disk materials. Neither the coherent transfer film nor the surface damage was observed on the surface of the novel zirconia/alumina composite disks during the test. The observed r,'stilts indicated that the wear of the polyethylene was closely related to contacting materials and kinematic motions. In conclusion, the novel zirconia/alumina composite leads the least wear of polyethylene among the tested ceramics and demonstrates the potential as lhe alternative materials for femoral head in total hip joint replacement.

• Korean Journal of Head & Neck Oncology
• /
• v.18 no.2
• /
• pp.179-183
• /
• 2002

Objective: A comparison of American Joint Committee on Cancer (AJCC) 1988 and 1997 nasopharyngeal carcinoma (NPC) classifications was made in terms of patient distribution and efficacy in predicting prognosis. Materials and Methods: Between Jan. 1981 and Dec. 1998, 60 cases of node negative nasopharyngeal carcinoma were retrospectively reviewed. The extent of disease each patients restaged according to the 4th and 5th AJCC system and Ho system, respectively. Results: The overall and disease free 5-year survival rates were 61.1% and 62.6%, respectively. Among T classifications of 4th AJCC, 5th AJCC and Ho staging system were not observed significantly different in disease-free survival rates, respectively. Conclusion: We observed a better patient distribution with AJCC 1997 comparing to AJCC 1988. The new classification also attained better statistical significances among stages in the overall survival and disease free survival rates was needed.

• Journal of Welding and Joining
• /
• v.4 no.2
• /
• pp.21-29
• /
• 1986

The influence of welding heat input variation(600-900J/cm) and heat-treatment condition after welding on tensile strength of butt welded joint in $175Kg/mm^2$ strength level Maraging steel(Co-free and Co-containing) sheets was investigated on the basis of hardness distribution, microstructure of weld metal and fracture surface. The obtained main results are as follows; 1. The strength of weldment (UTS, NTS), joint efficiency showed a little decreasing tendency with the increase in welding heat input, and the elongation showed a little increasing tendency with the increase in the width of weld metal. It was considered because of the plastic constraint of the high strength base metal. 2. The strength of weldment was better in the solution treatment and aging than the aging only after welding due to the disappearance of almost denverite in weld metal. 3. The hardness distribution in weldment after welding and heat-treatment was almost similar to both Co containing and Co free Maraging steel with change in welding heat input. 4. The fracture was occurred at weld metal, and the fracture surface showed a relatively shallow dimples in both Co containing and Co free Maraging steel.

• Journal of Welding and Joining
• /
• v.21 no.7
• /
• pp.59-64
• /
• 2003

Microstructure and shear strength of Sn-Zn lead-free solders and Au/Ni/Cu UBM joint under thermal aging conditions was investigated. The samples were aged isothermally at 10$0^{\circ}C$ and 15$0^{\circ}C$ for 300, 600, and 900 hours. The IMCs(Intermetallic Compound) at the interface between solder and UBM were examined by FESEM and TEM. The results showed that the shear strength was decreased with aging time and temperature. The solder ball with high activated RA flux had about 8.2% higher shear strength than that of RMA flux. Poor wetting and many voids were observed in the fractured solder joint with of RMA flux. The decreased shear strengths were caused by IMC growth and Zn grain coarsening. Zn reacted with Au and then was transformed to the $\beta$ -AuZn compound. Although AuZn grew first, $r-Ni_5Zn_{21}$ compounds were formed with aging time. The layers indicated by $Ni_5Zn_{21}(1)$, (2), and (3) were formed with the thickness of ∼0.7 ${\mu}{\textrm}{m}$, ∼4 ${\mu}{\textrm}{m}$, and ∼2 ${\mu}{\textrm}{m}$, respectively.

• The Journal of the Korean bone and joint tumor society
• /
• v.1 no.1
• /
• pp.60-67
• /
• 1995

It is difficult to manage the growing deformity of forearm bone caused by hereditary osteochondromatosis in children, because deformity and discrepancy of limb length is progressive. The are many treatment methods of these problems including excisio of osteochondroma, lengthening of ulna, shortening of radius, corrective osteotomy with or without lengthening apparatus. Among many treatment methods, we tried free vascularized epiphyseal transplantation with the proximal fibular epiphysis in 3 patients of hereditary osteochondromatosis for inducement of continuous bone growth and deformity correction. The average duration of follow up was 7 years and 1 month, the shortest duration being to 4 years and 5 months and the longest 10 years and 8 months. Serial radiologic and clinical evaluation were carried out during follow up and there were satisfactory length gain, deformity correction and improvement of adjacent joint motion in 2 cases. According to our follow up evaluation, free vascularized epiphyseal transplantation is valuable procedure in forearm deformity of hereditary osteochondromatosis although it needs skillful and experienced operative technique.

• Korean Journal of Applied Biomechanics
• /
• v.30 no.1
• /
• pp.37-49
• /
• 2020

Objective: The purpose of this study was to investigate the injury factors of Taekwondo jumping kick during landing phase according to the experience of injury and to suggest a stable landing movement applicable to free style Poomsae. Method: The participants were non-injury group (NG), n = 5, age: 20.5±0.9 years; height: 171.6±3.6 cm; body weight: 65.7±4.4 kg; career: 5.0±2.7 years. Injury group (IG), n = 9, age: 21.0±0.8 years; height: 170.9±4.6 cm; body weight: 67.1±7.0 kg; career: 8.6±5.0 years. The variables are impact force, loading rate, vertical stiffness, lower limb joint angle, stability, balance, and muscle activity in the landing phase. Results: NG was statistically larger than IG in the gluteus medius (p<.05). The impact force, loading rate and vertical stiffness decreased as the landing foot angle, the ROM of lower limb joint angle and COM displacement increased (p<.05). Conclusion: Based on the results, it means that the landing foot angle plays an important role in the impact reduction during landing phase. It is required the training to adjust the landing foot angle.