• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.520-528
• /
• 1994

An investigation was carried out to understand the effect of the amount of free silicon on the tribological properties of Si-SiC. The specimens of dense Si-SiC composites with various amount of free silicon were fabricated in the temperature of 175$0^{\circ}C$ after molding under various pressure. Wear properties were measured by ball-on-plate wear tester under the constant weight of 4 Kgf at constant sliding speed of 500 mm/sec in water. As the result, the Rockwell hardness and fracture strength of Si-SiC composites remained nearly constant up to 16.62 vol% of free silicon in the Si-SiC microstructure. The Si-SiC composites containing the free silicon of 16.62 vol% was considered to be prominent in the tribological properties, which had the friction coefficient of 0.08 and the specific wear rate of 2.4$\times$10-8$\textrm{mm}^2$Kgf-1. The analysis of the wear surface indicated the complicated processes occuring on the surface such as fine polishing, abrasion, microfracture.

• Journal of Welding and Joining
• /
• 제18권6호
• /
• pp.74-82
• /
• 2000

The fluxless wetting properties of UBM-coated Si-wafer to the binary lead-free solders(Sn-Ag, Sn-Sb, Sjn-In, Sn0Bi) were estimated by wetting balance method. With the new wettability indices from the wetting curves of one side coated specimen, the wetting property estimation of UBM-coated Si-wafer was possible. For UBM of Si-chip, Au/Cu/Cr UBm was better than au/Ni/TI in the point of wetting time/ At general reflow process temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) was better than that of low melting point one(Sn-Bi, Sn-In). The contact angle of the one side coated Si-plate to the solder could be calculated from the force balance equation by measuring the static state force and the tilt angle.

• 한국자기학회지
• /
• 제16권6호
• /
• pp.276-278
• /
• 2006

스위칭 특성을 향상시키기 위하여 비정질 강자성 CoFeSiB 자유층을 갖는 자기터널접합 (MTJ)의 스위칭 특성을 연구하였다. 자기터널접합의 구조는 $Si/SiO_{2}/Ta$ 45/Ru 9.5/IrMn 10/CoFe 10/CoFe $7/AlO_{x}/CoFeSiB\;(t)/Ru\;60\;(nm)$이다. CoFeSiB는 $560\;emu/cm^{3}$의 낮은 포화자화도와 $2800\;erg/cm^{3}$의 높은 이방성 상수를 가졌다. 이러한 특성이 자기터널접합의 낮은 보자력($H_{c}$)과 높은 자장민감도를 갖게 한다. 이것은 또한 Landau-Lisfschitz-Gilbert 방정식에 근거한 미세자기 전산시뮬레이션을 통하여 submicrometersized elements에서도 확인하였다. CoFeSiB 자유층 두께를 증가함으로서 스위칭 특성은 반자화 자기장의 증가로 인하여 더욱더 나빠졌다.

• 한국세라믹학회지
• /
• 제38권6호
• /
• pp.531-536
• /
• 2001

SiCl$_4$/CH$_4$/H$_2$계를 사용한 플라즈마 화학증착법(PECVD)으로 실리콘(100) 기판 위에 3C-SiC막을 117$0^{\circ}C$~1335$^{\circ}C$의 온도범위에서 증착하였다. 증착온도, 유입가스비, R$_{x}$ [=CH$_4$/(CH$_4$+H$_2$)], 그리고 r.f. power를 변화시켜 증착막의 결정성에 대해 검토하였다. Thermal CVD에 비해 PECVD법은 박막의 증착속도를 향상시켰다. 증착된 3C-SiC은 (111) 면으로 최대의 우선배향성을 지님을 알 수 있었다. 실리콘 기판 위의 3C-SiC막의 결정성은 R$_{x}$값에 의존하였으며, R$_{x}$가 감소할수록 결정성이 더욱 향상되었다. Free Si가 3C-SiC막과 함께 증착되었으나, 증착온도와 r.f power가 증가함에 따라 free Si의 함량은 감소하였다. 증착온도 127$0^{\circ}C$, 유입가스비 R$_{x}$=0.04, r.f. power가 60W에서 비교적 결정성을 가진 3C-SiC막을 얻을 수 있었다.

• 한국결정성장학회지
• /
• 제11권4호
• /
• pp.160-165
• /
• 2001

The effects of various metals on Field Aided Lateral Crystallization (FALC) behaviors of amorphous silicon (a-Si) were investigated. Under an influence of electric field, metals such s Cu, Ni and Co were found to fasten the lateral crystallization toward a metal-free region, exhibiting a typical FALC behavior while the lateral crystallization of a-Si was not obvious for Pd. However, Au, Al and Cr did not induce the lateral crystallization of a-Si in metal-free region. Such phenomenological differences in various metals were studied in terms of dominant diffusing species (DDS) in the reaction between metal and Si. It was judged that the applied electric field enhanced the crystallization velocity by accelerating the diffusion of metal atoms since the occurrence of lateral crystallization would be strongly dependent on the diffusion of metal atoms than that of Si atoms. Therefore, it was concluded that he only metal-dominant diffusing species in the reaction between metal and Si results in the crystallization of a-Si in metal-free region.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.61.2-61.2
• /
• 2010

Ag thick-film has usually been used for the front electrode of Si solar cells with the outstanding electrical properties. Ag paste consists of Ag powers, vehicles, frits and additives. Ag paste has broadly been screen-printed on the front side of Si wafer with the merits of low cost and simplicity. The optimal contact formation between Ag electrodes and Si wafer in the front electrode during a fast firing has been considered as the key factor for high efficiency. Although the content of frit in Ag pastes is less than 5wt%, it can profoundly influence the contact formation between Ag and Si under the fast firing. In this study, the effects of lead-free frits on the contacts between Ag and Si were studied with the thermal properties and compositions of various frits. Our experimental results showed that the electrical properties of cells were related to the interface structures between Ag and Si. It was found that current path of electrons from Si to Ag would be possible through the tunneling mechanism assisted by tens of nano-Ag recrystals on $n^+$ emitter as well as Ag recrystals penetrated into $n^+$ emitter layers. These preliminary studies will be helpful for designing the proper frits for the Ag pastes with considering the properties of various Si wafers.

• Journal of Welding and Joining
• /
• 제33권3호
• /
• pp.19-24
• /
• 2015

Joint properties of electric control unit (ECU) module using Sn-Cu-(X)Al(Si) lead-free solder alloy were investigated for automotive electronics module. In this study, Sn-0.5Cu-0.01Al(Si) and Sn-0.5Cu-0.03Al(Si) (wt.%) lead-free alloys were fabricated as bar type by doped various weight percentages (0.01 and 0.03 wt.%) of Al(Si) alloy to Sn-0.5Cu. After fabrications of lead-free alloys, the ball-type solder alloys with a diameter of 450 um were made by rolling and punching. The melting temperatures of 0.01Al(Si) and 0.03Al(Si) were 230.2 and $230.8^{\circ}C$, respectively. To evaluation of properties of solder joint, test printed circuit board (PCB) finished with organic solderability perseveration (OSP) on Cu pad. The ball-type solders were attached to test PCB with flux and reflowed for formation of solder joint. The maximum temperature of reflow was $260^{\circ}C$ for 50s above melting temperature. And then, we measured spreadability and shear strength of two Al(Si) solder materials compared to Sn-0.7Cu solder material used in industry. And also, microstructures in solder and intermetallic compounds (IMCs) were observed. Moreover, thickness and grain size of $Cu_6Sn_5$ IMC were measured and then compared with Sn-0.7Cu. With increasing the amounts of Al(Si), the $Cu_6Sn_5$ thickness was decreased. These results show the addition of Al(Si) could suppress IMC growth and improve the reliability of solder joint.

• 대한화학회지
• /
• 제54권6호
• /
• pp.723-726
• /
• 2010

마이크로 반응을 이용하여 $NaHSO_4/SiO_2$을 촉매로 하는 solvent-free 합성을 통하여 $\beta$-enaminone 과 2-methylquinolin-4(1H)-one 및 그 유도체를 합성하는 효율적인 방법을 개발하였다. 반응 시간이 짧고, 수율이 좋았으며, 마이크로웨이브를 사용하지 않는 반응보다는 높은 선택성, 간단성, 무용매 반응 및 친환경적인 반응이다.

• 한국주조공학회지
• /
• 제12권4호
• /
• pp.335-345
• /
• 1992

Aluminum alloy matrix composites reinforced with various amounts of SiC particles have been produced by rheo-compocasting followed by hot extrusion. A relatively uniform distribution of SiC particles in the composites was obtained. The amounts of pore and SiC particles cluster were relatively small in the composites. Particle free zones were observed in the hot extruded composites when the amount of SiC particles was less than 20 vol%. However, the width of particle free zone decreases with the increase of SiC particle content. Eutectic Si phase play an important role for improving bonding between SiC particle and matrix. Tensile and yield strength increased with the increase of SiC particle content. the strenthening effect of SiC particle addition was effective even at relatively high temperature of 573 K.

• 전기화학회지
• /
• 제9권1호
• /
• pp.34-39
• /
• 2006

Li free 음극으로써 구리 foil 집전체에 $Li_{0.5}La_{0.5}TiO_3$ 및 Si 박막을 r.f, 스퍼터링법을 이용하여 증착하고 양극 물질로는 $Li[Co_{0.1}Ni_{0.15}Li_{0.2}Mn_{0.55}]O_2$를 이용하여 전기화학적 특성을 평가하였다. 박막 증착시 플라즈마 내(in-plasma)와 밖(out of plasma)에 구리 foil을 각각 위치시켰다. X-ray 회절 분석의 경우 각각의 조건에서 $Li_{0.5}La_{0.5}TiO_3$ 및 Si 모두 결정 특성의 차이를 발견할 수 없었다. $Li_{0.5}La_{0.5}TiO_3$의 경우 플라즈마 내에서 증착된 경우 그리고 Si 경우는 플라즈마 밖에서 증착된 경우 각각 싸이클 특성이 우수한 것으로 나타났다. 이는 $Li_{0.5}La_{0.5}TiO_3$ 경우 결정성이 존재할 경우 이온전도 특성이 우수하며 Si 경우 플라즈마 내에서 성장된 박막이 더욱 치밀하여 충방전 중 부피변화에 더욱 민감하였기 때문으로 판단된다. 이상의 결과로부터 (1)전지 용량을 갖는 5게 의한 표면 개질의 경우 구조적으로 안정할 수 있는 비정질 상의 Si이 보다 더 바람직하며 (2) 이온전도 특성을 보이는 $Li_{0.5}La_{0.5}TiO_3$와 같은 소재를 이용하여 표면 개질을 할 경우 Li의 확산이 더욱 용이한 구조가 바람직할 것으로 판단된다.