• 지질공학
• /
• 제8권3호
• /
• pp.207-213
• /
• 1998

이 연구는 팽창성 시멘트의 팽창압에 의한 암석 파괴 시에 발생하는 AE 파의 특성을 규명하기 위하여 수행되었다. 연구결과 AE파의 우세 주파수와 최대 진폭은 팽창성 시멘트 충전공에서의 압력 발달 비율과 관련하여 변화되었다. AE파의 우세 주파수는 소 직경 충전공 시험에서 150∼230kHz이었고 대 직경 충전공에서 400∼500kHz이었으며, 최대 진폭은 각각 0.015∼0.050cm/sec 및 0.025∼0.064cm/sec이었다. 시험에서 충전공의 크기에 따라 각기 높은 주파수의 큰 진폭과 낮은 주파수의 작은 진폭의 AE파가 수신된다는 사실은 동일 시료에서 일정한 규모의 균열을 발생시키는데 필요한 총 에너지는 대체로 동일함을 강하게 암시하고 있다. 팽창성 시멘트에 의한 암석 균열은 진폭이 특별히 큰 AE파의 발생없이 안정적으로 진행되어서 거시적 암석균열은 미소균열의 안정적 성장의 결과임을 시사하였다.

• 자원환경지질
• /
• 제27권4호
• /
• pp.325-333
• /
• 1994

Gold and/or silver mineralization in the southeast province, Korea, occurred in hydrothermal quartz vein that fills fracture zones in Cretaceous volcanic and sedimentary rocks of the Gyeongsang basin or granites and Precambrian gneiss. Most of the gold-silver-bearing veins in the province occur in Hapcheon, Suncheon and Haman-Gunbuk area where they are associated with Cretaceous Bulgugsa granites. On the basis of the Ag/Au ratio on amounts produced and ore grades, mode of occurrence, and associated mineral assemblages, hydrothermal Au-Ag deposits in southeast province, Korea, can be classified as follows: pyrite-type gold deposit (Group IIB, Samjeong and Sangchon deposits), antimony-type gold-silver deposit (Group IV, Gisan and Geochang deposits), and antimony-type silver deposit (Group V, Sanggo, Seweon, Seongju and Gahoe deposits). All of the gold-silver deposits in the province are generally characteristics of the gold-silver or silver-dominant type deposit which contains more silver-bearing minerals than those deposits in central Korea. The gold-silver mineralization in the deposits consist of two generation; the early characterized by gold precipitation and the late represented by silver-rich (as silver-bearing sulfosalts minerals) mineralization. All but one deposit (Samjeong deposit) having relatively lower Au content in electrum values between ${\approx}20$ and ${\approx}50$ atomic %. The mineralogical data on electrum-sphalerite and/or arsenopyrite geothermometry and fluid inclusion data indicate that the gold and silver mineralizations were occurred at temperatures of $190{\sim}280^{\circ}C$ and $150{\sim}180^{\circ}C$, respectively. These suggest that the gold-silver mineralization in the province occurred in the lower temperature and pressure conditions as epithermal-type hydrothermal vein deposit.

• 한국주조공학회지
• /
• 제31권1호
• /
• pp.11-17
• /
• 2011

The effect of CaO addition to AM60B Mg alloy on tensile properties has been investigated, with focus on strength and ductility at room and elevated temperatures. The 0.25-0.65wt% CaO added AM60B Eco-Mg diecastings were prepared by high pressure die casting using Buhler 1,450-ton cold chamber machine without $SF_6$ and $SO_2$ gases. The microstructures and tensile properties of each alloy were tested. The results show that the grains of AM60B are refined and the mechanical properties increase with CaO addition at room temperature. The improvement of strength and ductility is prominent at 0.45-0.55wt% CaO addition. Also, improved mechanical properties are maintained at elevated temperature of $150^{\circ}C$. CaO addition results in $Al_2Ca$ phase formation mostly on the grain boundaries. This phase leads to the refinement of grain structures and improvement of ductility as well as strength. The suppression of ${\beta}-Mg_{17}Al_{12}$ phase as well as the decrease of fracture surface porosity and other casting defects caused by melt cleanliness also contribute to the enhancement of mechanical properties of AM60B Eco-Mg at room and elevated temperature.

• 한국세라믹학회지
• /
• 제26권6호
• /
• pp.771-782
• /
• 1989

Synthesis of $\beta$-Sialon powder was attempted with carbothermal reduction of porous glass. The porous glass was prepared by heat and hydrothermal treatments of 9.32 Li2O.46.5B2O3.37.2SiO2.6.98Al2O3 glass. Carbon pyrolyzed from propane gas was deposited on the porous glass, thereafter activated carbon was added as reducing agents. The synthesized $\beta$-Sialon powder was pressureless sintered at 175$0^{\circ}C$ for 1hr in N2 atmosphere. The characterization of the $\beta$-Sialon powder was performed with XRD, BET, SEM and particle size analysis. The sinterability and mechanical properties of the sintered bodies were investigated in terms of bulk density, M.O.R., fracture toughness, morphology of microstructure and etc. The reduction effect of deposited carbon was better than that of activated carbon mechanically added. The formation of SiC was precominant over that of Si2ON2 and $\beta$-Sialon owing to low partial pressure of N2 inside the pore, wehreas on the surface of porous glass the formation of Si2ON2 and $\beta$-Sialon were predominant. Thereafter, SiC reduced unreacted glass to be $\beta$-Sialon. Single phase of $\beta$-Sialon(Z=1.92) was obtained from PGA porous glass having the largest pore radius by the simultaneous reduction and nitridation method at 145$0^{\circ}C$ for 5hrs. The bulk density, M.O.R., and KIC of the sitered body are 3.17g/cc, 434.4MPa and 4.1MPa.m1/2, respectively.

• Nuclear Engineering and Technology
• /
• 제47권3호
• /
• pp.340-350
• /
• 2015

This paper proposes strain-based acceptance criteria for assessing plastic instability of the safety class 1 nuclear components made of ferritic steel during level D service loads. The strain-based criteria were proposed with two approaches: (1) a section average approach and (2) a critical location approach. Both approaches were based on the damage initiation point corresponding to the maximum load-carrying capability point instead of the fracture point via tensile tests and finite element analysis (FEA) for the notched specimen under uni-axial tensile loading. The two proposed criteria were reviewed from the viewpoint of design practice and philosophy to select a more appropriate criterion. As a result of the review, it was found that the section average approach is more appropriate than the critical location approach from the viewpoint of design practice and philosophy. Finally, the criterion based on the section average approach was applied to a simplified reactor pressure vessel (RPV) outlet nozzle subject to SSE loads. The application shows that the strain-based acceptance criteria can consider cumulative damages caused by the sequential loads unlike the stress-based acceptance criteria and can reduce the overconservatism of the stress-based acceptance criteria, which often occurs for level D service loads.

• Journal of Welding and Joining
• /
• 제26권4호
• /
• pp.85-91
• /
• 2008

The grooving corrosion is caused mainly by the different microstructures between the matrix and weld which is formed during the rapid heating and cooling cycle in welding. By this localized corrosion reaction of pipes, it evolves economic problems such as the early damage of industrial facilities and pipe lines of apartment, and water pollution. So lots of researches were carried out already about grooving corrosion mechanism of ERW carbon steel pipe but there is seldom study for water hammer happened by fluid phenomenon and corrosion rate by flow velocity. In this study, the analysis based on hydrodynamic and fracture mechanics was carried out. ANSYS, FLUENT and STAR-CD were used for confirmation of flow phenomenon and stress on the pipe. As the results, fatigue failure is able to be happened by water hammer and grooving corrosion rate is increased cause by turbulent. Grooving corrosion is happened on the pipe, then friction loss of fluid is occurred from corroded part. Erosion can be happened enough in corroded region of microscopic size that wear "V" form. Also pipe is able to be damaged by water hammer effects because of corroded region is general acting as a notch effects. Corrosion depth was more than half of total thickness, it can be damaged from water hammer pressure.

• 한국세라믹학회지
• /
• 제38권11호
• /
• pp.987-992
• /
• 2001

내화물 등급의 저가 질화규소 분말을 분석 및 가공한 후, 소결조제을 첨가하여 가스압 소결하였다. 원료분말에는 다량의 free Si가 있었으며 Fe, Al, Ca등의 불순물도 각각 0.72wt%, 0.5wt%, 0.31wt%로 다량 존재하였다. 산소와 탄소의 함량도 각각 3.3wt%와 0.4wt%로 많았으며, 96%의 $\beta$-상과 4%의 $\alpha$-상으로 구성하였다. 원료 분말을 탈철처리 및 질화처리 하여 소결조제인 6wt% yttria와 2wt% alumina를 첨가하고, 1823K-2133 K의 온도 범위에서 1시간씩 소결하여 소결거동을 조사하였다. 또, 2123K에서 2시간동안 소결하여 충분히 치밀화된 소결체를 얻었다. 비교를 위하여 상용 질화규소 분말을 같이 소결하여 소결거동과 기계적 특성 등을 조사하였다. 저가의 분말을 상용 분말보다 치밀화 속도는 늦었다. 충분히 치밀화된 저가 분말의 소결체는 낮은 aspect rtio를 갖는 조대 결정립들이 다수 존재하였으며, 경도, 파괴인성, 꺽임강도, 내열 충격성 등이 상용 분말의 소결체 보다 떨어졌다.

• Advances in materials Research
• /
• 제1권1호
• /
• pp.51-74
• /
• 2012

A powder metallurgy-based rapid consolidation technique, Plasma Pressure Compaction ($P^2C^{(R)}$), was utilized to produce near-net shape parts of gamma titanium aluminides (${\gamma}$-TiAl). Micron-sized ${\gamma}$-TiAl powders, composed of Ti-50%Al and Ti-48%Al-2%Cr-2%Nb (at%), were rapidly consolidated to form near-net shape ${\gamma}$-TiAl parts in the form of 1.0" (25.4 mm) diameter discs, as well as $3"{\times}2.25"$ ($76.2mm{\times}57.2mm$) tiles, having a thickness of 0.25" (6.35 mm). The ${\gamma}$-TiAl parts were consolidated to near theoretical density. The microstructural morphology of the consolidated parts was found to vary with consolidation conditions. Mechanical properties exhibited a strong dependence on microstructural morphology and grain size. Because of the rapid consolidation process used here, grain growth during consolidation was minimal, which in turn led to enhanced mechanical properties. Consolidated ${\gamma}$-TiAl samples corresponding to Ti-48%Al-2%Cr-2%Nb composition with a duplex microstructure (with an average grain size of $5{\mu}m$) exhibited superior mechanical properties. Flexural strength, ductility, elastic modulus and fracture toughness for these samples were as high as 1238 MPa, 2.3%, 154.58 GPa and 17.95 MPa $m^{1/2}$, respectively. The high temperature mechanical properties of the consolidated ${\gamma}$-TiAl samples were characterized in air and vacuum and were found to retain flexural strength and elastic modulus for temperatures up to $700^{\circ}C$. At high temperatures, the flexural strength of ${\gamma}$-TiAl samples with Ti-50%Al composition deteriorated in air by 10% as compared to that in vacuum. ${\gamma}$-TiAl samples with Ti-48%Al-2%Nb-2%Cr composition exhibited better if not equal flexural strength in air than in vacuum at high temperatures.

• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.524-531
• /
• 2004

To investigate relevance of the definition of the reference stress to estimate J and $C^{*}$ for surface crack problems, this paper compares FE J and $C^{*}$ results for surface cracked pipes with those estimated according to the reference stress approach using various definitions of the reference stress. Pipes with part circumferential inner surface crack and finite internal axial crack are considered, subject to internal pressure and global bending. The crack depth and aspect ratio are systematically varied. The reference stress is defined in four different ways using (i) the local limit load, (ii) the global limit load, (iii) the global limit load determined from the FE limit analysis, and (iv) the optimized reference load. It is found that the reference stress based on the local limit load gives overall excessively conservative estimates of J and $^{*}$. Use of the global limit load clearly reduces the conservatism, compared to that of the local limit load, although it can provide sometimes non-conservative estimates of J and $^{*}$. The use of the FE global limit load gives overall non-conservative estimates of J and $^{*}$. The reference stress based on the optimised reference load gives overall accurate estimates of J and $^{*}$, compared to other definitions of the reference stress. Based on the present finding, general guidance on the choice of the reference stress for surface crack problems is given.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제28권5호
• /
• pp.383-389
• /
• 2002

This is a retrospective study on emergency patients with active oral bleeding. The study was based on a series of 135 patients treated as emergency patients at Wonju Christian Hospital, from Jan. 1, 1997, to Dec. 31, 2001. The postoperative bleeding was the most frequent cause of active oral bleeding in emergency room and bleeding from trauma and medically compromised (bleeding disorders) patients were next in order of frequency. In the injury of maxillofacial vessels, peak incidence was occurred in the inferior alveolar vessel (42.9%), followed by the submucosal vessel of lip & cheek, the superior alveolar vessel, and sublingual vessels. The most common disease of bleeding disorders was vascular wall alteration (infection, etc), followed by liver disease, thrombocytopenic purpura, anti-coagulation drugs in order. In the characteristics of dental diseases on bleeding disorders, periodontal disease and alveolar osteitis (osteomyelitis) were more common. The hemostasis was most obtained by use of wound suture, simple pressure dressing, drainage for infection control and primary interdental wiring of fracture. In the complication group, the infrequent incidence was showed in vomiting, hypovolemic shock, syncope, recurred bleeding & aspiration pneumonia. In the uncontrolled oral bleeding, the injured vessels were suspected as skull base & ethmoidal vessels. In this study, authors found that the close cooperation between the dentistry (Oral and maxillofacial surgery) and the medicine (emergency & internal medicine) was the most important for early proper control of active oral bleeding. And then post-operative wound closure, drainage for infection control and previous systemic evaluation of bleeding disorders were critical for the prevention of postoperative bleeding in the local dental clinic.