• Transactions of Materials Processing
• /
• v.13 no.2
• /
• pp.129-136
• /
• 2004

Recently, instead of a matched die forming method requiring a high cost and long delivery term, a multi-point dieless forming method using a pair of matrix type punch array as flexible dies has been developed. Since the conventional multi-point dieless forming method has some disadvantages of difficulty in precise punch control and high-cost of equipment, a new concept of multi-point dieless forming method combined with an elasto-forming method has been suggested in this study. For optimal selection of elastomers, compression tests of rubbers, polyethylene and foams were carried out together with FEM analysis of the deformation behavior during sheet forming process using a rigid punch and elastomers. Compressive strain was concentrated on the upper central area of the elastomer under the punch, and the rubber exhibited higher concentration of the compressive strain than foams. Two-dimensional curved surface was formed successfully by the multi-point elasto-dieless forming method using an optimal combination of rubber and foam materials.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.08a
• /
• pp.21-28
• /
• 2003

Recently, instead of a matched die forming method requiring a high cost and long deliverly ten a multi-point dieless forming method using a pair of matrix type punch array as flexible dies has been developed. As this multi-point dieless forming method has some disadvantage of difficulty in precise punch control and high-cost of equipment, a new concept of multi-point dieless forming method combined with elastomer forming was suggested in this study. For optimal selection of elastomers, compression tests of rubbers, polyethylene and foams were carried out together with FEM analysis of the deformation behavior during sheet forming process using a rigid punch and elastomers. Compressive strain was concentrated on the upper central area of the elastomer under the punch, and the rubber exhibited higher concentration of the compressive strain than foams. Two-dimensional curved surface was formed successfully by the multi-point elasto-dieless forming method using an optimal combination of a rubber and foam.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.38 no.4
• /
• pp.177-183
• /
• 2015

Incremental sheet metal forming is a manufacturing process to produce thin parts using sheet metals by a series of small incremental deformation. The process rarely needs dedicated dies and molds, thus, preparation time for the process is relatively short as to be compared to conventional metal forming. Spring back in sheet metal working is very common, which causes critical errors in dimensions. Incremental sheet metal forming is not fully investigated yet. Hence, incremental sheet metal forming frequently produces inaccurate parts. This paper proposes a method to minimize dimensional errors to improve shape accuracy of products manufactured by incremental forming. This study conducts experiments using an exclusive incremental forming machine and the material for these experiments are sheets of aluminum AL1015. This research defines a process parameter and selects a few factors for the experiments. The parameters employed in this paper are tool feed rate, tool diameter, step depth, material thickness, forming method, dies applied, and tool path method. In addition, their levels for each factor are determined. The plan of the experiments is designed using orthogonal array $L_8$ ($2^7$) which requires minimum number of experiments. Based on the measurements, dimensional errors are collected both on the tool contacted surfaces and on the non-contacted surfaces. The distances between the formed surfaces and the CAD models are scanned and recorded using a commercial software product. These collected data are statistically analyzed and ANOVAs (analysis of variances) are drawn up. From the ANOVAs, this paper concludes that the process parameters of tool diameter, forming depth, and forming method are the significant factors to reduce the errors on the tool contacted surface. On the other hand, the experimental factors of forming method and dies applied are the significant factors on the non-contacted surface. However, the negative forming method always produces better accuracy than the positive forming method.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.113-119
• /
• 1995

The green body was fabricated by a new forming method, pressureless powder packaing forming method, and the characteristics of sintered specimen were investigated. It was found that alumina ceramics prepared by the present method showed porous structure with narrow pore size distribution, and in case of abrasive powder sintered body, compared with dry-pressed specimen, had the nearly same density. Especially, the specimen prepared with spray-dried granules showed the characteristic that granules were not either deformed or fractured during forming and sintering process. Therefore, it was found that this new forming method was effective method in fabrication of porous ceramics on account of easy control of porosity and pore size and its high thermal stability.

• Journal of the Korean Ceramic Society
• /
• v.31 no.1
• /
• pp.31-38
• /
• 1994

To overcome the demerit of conventional forming method, new forming method, pressureless powder packing forming method, was investigated. This technique is performed by powder packing followed by the infiltration of binder solution. Various alumina powders were used as starting materials and the powders showing good packing condition through powder packing experiment were chosen. The green densities prepared by this new forming method with these powders were lower than those of specimens by pressing method, but, nearly same density was obtained in case of green body prepared with the powders having high packing density. The distribution of binder in a green body was homogeneous and it was possible to a complex shape form by this forming method.

• Journal of the Korean Ceramic Society
• /
• v.32 no.6
• /
• pp.710-718
• /
• 1995

The new forming method, Pressureless Powder Packing Forming Method was applied to the manufacturing of reaction sintered SiC. After the experiments of vibratory powder packing and binder infiltration, the abrasive SiC powder of which mean size is 45${\mu}{\textrm}{m}$ was selected to this forming method. Uniform green bodies with porosity of 45% and narrow pore size distribution could be formed by this new forming method. Also, complex or varied cross-sectional shapes could be easily manufactured through the silicone rubber mould used in this forming method. Maximum 15 wt% amorphous carbon was penetrated into green body by multi impregnation-carbonization cycles. And reaction-bonded SiC was manufactured by infiltration of SiC-carbon shaped bodies with liquid silicon.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.66-69
• /
• 2002

In the ideal forming theory(1), which has been deviously developed as a direct method for optimizing forming process, material elements are required to deform following the minimum plastic work path (or the proportional true strain path). Besides the general theory(2,3), specific ideal forming theories have been developed for membrane sheet forming(4) as well as two-dimensional steady bulk forming(5-7). In this work, the ideal forming theory was successfully applied for non-steady bulk forming under the plane strain condition. Here, the shape change complying with the minimum plastic work path, was effectively described by developing a numerical code based on the characteristic method. Numerical results obtained for a specific industrial part also include the optimum pre-forming shape and its evolving shape change to the final shape as well as the boundary traction history.

• Transactions of Materials Processing
• /
• v.11 no.3
• /
• pp.223-230
• /
• 2002

Matched die forming technology has been used widely as a sheet metal forming method for a long time. This conventional method, however, needs a high cost and long delivery time to prepare a set of matched dies or, in many cases, several sets of dies. For more than ten years, some alternative methods using single die or non-matched dies have been developed and applied practically in various fields of industry. Elasto-forming, fluid forming, hydro-forming, and blow forming are some examples of these new methods. Recently, a dieless sheet forming technology using a reconfigurable matrix of punch elements has been developed, and started to be used in some industries such as aircraft and railroads. A new concept of dieless forming technology has also been proposed to overcome the drawback of the conventional dieless forming technology.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.16-22
• /
• 2005

The flow forming has been used to produce long thin walled tube parts, with reduced forming force and enhanced mechanical and surface quality for a good finished part, compared with other method formed parts. So flow forming technique is used widely in industrial production. Especially spinning and flow forming techniques are used frequently in automotive, aerial, defense industry. In this paper, finite element method analysis of three-roller backward flow forming of a workpiece is carried out to study effects of forming depth and feed rate on forming force. The axial and radial forces on several forming depth and feed rate conditions are obtained.

• Transactions of Materials Processing
• /
• v.21 no.4
• /
• pp.234-239
• /
• 2012

This study examines the forming properties and forming loads needed to increase the edge thickness on the external face of a plate using finite element analysis(FEA). Recently, forming optimization techniques within FEA are being extensively used in designing the optimal forming conditions for processes like forging, extrusion, rolling, and spinning. Most of these existing forming operations involve reducing the volume per unit length, but research for increasing volume per unit length is not very extensive. For this study we chose an automotive engine flywheel which is a welded assembly of a plate and a gear with each component having a different thickness. We considered a forming technique to increase the thickness in order to allow the machining of the gear directly on the external face of plate alleviating the need for a weld. To study various forming techniques, we used the finite element method with the flow stress of material and incremental forming steps. We conclude from this study that the analysis of forming properties and forming loads by using the finite element analysis and testing is useful as a method to increase the thickness per unit length.