• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.1
• /
• pp.191-200
• /
• 1992

In order to simulate the line heating process which is a three-dimensional transient thermo elastic plastic state, a simple modified strip model is suggested. First attempt is made to verify the validity of the model using a finite element program, and the result gives good agreement with the plate theory where conventional two-dimensional model fails totally.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1994.10a
• /
• pp.118-132
• /
• 1994

This paper investigates a new method to design blocker geometry in rib-web type closed die forging. By examining various forging and blocker geometries, it was found that blocker geometry can be generated by eliminating high frequency mode from finisher geometry. In order to formalize the procedure, low pass filters, which can convert finisher to blocker geometry, are proposed. Also discrete Fourier transform is used for computational efficiency. The blocker geometry designed by the present method are compared with the one by an experienced designer. The blocker geometries are also validated by using FEM simulation. Present results shows that the frequency approach may offer a promising method to design blocker automatically.

• Transactions of Materials Processing
• /
• v.18 no.1
• /
• pp.80-86
• /
• 2009

This paper presents the plastic inhomogeneous deformation behavior of bimetal composite rods during the axisymmetric and steady-state extrusion process through a conical die. The rigid-plastic FE model considering frictional contact problem was used to analyze the co-extrusion process with material combinations of Cu/Al. Different cases of initial geometry shape for composite material were simulated under different conditions of co-extrusion process, which includes the interference and frictional conditions. From the simulation results, the sleeve cladding rate at the core/sleeve interface was recorded as a distribution of diameter ratio and interference conditions, which will be useful for the investigations of the bonding process during co-extrusion process. In addition, the results of the co-extrusion, connected with the results of the variations of diameter rate and average contact pressure, demonstrate a good agreement and present the possibility of describing the parameters of the plastic zones in non-uniform deformation of these type of composite materials.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.437-440
• /
• 2009

In this paper, an aluminum ring forging process of manufacturing an optimized perform for a hot forging process is simulated using AFDEX 3D, a general-purpose metal forming simulator based on rigid-thermoviscoplastic finite element method. Non-isothermal analysis is carried out and the predictions are compared with the experiments in terms of dimensional accuracy. It was shown that the predictions are in good agreement with the experiments.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.213-214
• /
• 2009

Recently the use of ferritic stainless steels for automotive exhaust system has been increased dramatically. A detailed knowledge of material behavior of ferritic stainless steel is important for successful manufacturing of exhaust systems. To achieve this goal, numerical study of square cup deep drawing for ferritic stainless steel sheet, type 409L was conducted with Yld2000-24. Uniaxial tensile test and hydraulic bulge test were performed to characterize plastic material behavior. Finite element simulation of square cup deep drawing was performed successfully.

• Transactions of Materials Processing
• /
• v.23 no.7
• /
• pp.446-452
• /
• 2014

In the current study finite element forming analysis is performed to understand the final geometric accuracy limitations for the stamping of an automotive S-rail from four different steel sheets having tensile strengths of 340MPa, 440MPa, 590MPa and 780MPa. Comparisons between the analysis and the experiments for both springback and formability as measured by the amount of edge draw-in and the thickness distribution were conducted. The springback modes were classified according to a scheme proposed in the current investigation and the error was calculated using the normalized root mean square error method. While the analysis results show fairly good agreement with the experimental data for deformation and formability, the simulation accuracy is lower for predicting wall curl, camber and section twist as the UTS of steel sheet increases.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2004.10a
• /
• pp.345-348
• /
• 2004

Every bridge node participating in multiple piconets and forming a scatternet should schedule the inter-piconet traffics in an efficient manner. Frequent piconet switching due to short polling intervals for the links of a bridge node leads to considerable time slots loss caused by the guard time and power consumption for transceiving and processing. On the other hand, restrained piconet switching may result in failures of fulfilling QoS (Quality of Service) requirements for some links. Tn this paper, we present a QoS aware inter-piconet scheduling scheme minimizing the piconet switching events within guaranteed QoS requirements. According to simulation results, the proposed scheme is confirmed to have great improvement in throughput and number of switching events over the credit scheme as current inter-piconet scheduling scheme for the scatter mode.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.6
• /
• pp.33-42
• /
• 1997

In this paper, a new structure for a dC plasma display pane(PDP) with a wall-catode and a wall-auxilizry anode has been suggested. The wall-cathode with a sufficient discharge area maximizes the discharge volume. The auxiliary anode surrounding the discharge region makes the effective control of the charged particles possible. We have investigated the cahracteristics of the new cell structure with a 2-dimensional computer simulation and a micro gap discharge system, and compared experimentally with those of previous cell structure. The new cell structure with the wall-cathode and auxiliary wall-anode turned out to have improved luminance, discharge forming time and sustain voltage.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.1
• /
• pp.34-39
• /
• 2013

In this paper, we described the study on back-radiation level improvement of IFF antenna after briefly describing a design of IFF antenna to distinguish the target as the sub-antenna of surveillance radar. The proposed IFF antenna was minimized a size with use all-in-one power divider as a two-channel IFF antenna forming sum and difference pattern. The method for back-radiation level reduction was studied, and the identified method through the simulation confirmed the decrement throught the measurement.

• ETRI Journal
• /
• v.11 no.2
• /
• pp.109-119
• /
• 1989

Based on the 2-dimensional charge-control simulation[4], a purely analytical model for MODFET's is proposed. In this model, proper treatment of the diffusion effect in the 2-DEG transport due to the gradual channel opening along the 2-DEG channel was made to explain the enhanced mobility and increased thershold voltage. The channel thickness and gate capacitance are experssed as functions of gate vlotage including subthreshold characteristics of the MODFET's analytically. By introducing the finite channel opening and an effective channel-length modulation, the slope of the saturation region of the I-V curves was modeled. The smooth transition of the I-V curves from linear-to-saturation region of the I-V curves was possible using the continuous Troffimenkoff-type of field-dependent mobility. Furthermore, a correction factor f was introduced to account for the finite transtition section forming between the GCA and the saturated section. This factor removes the large discrepanicies in the saturation region fo the I-V curves presicted by existing 1-dimensional models. The fitting parameters chosen in our model were found to be predictable and vary over relatively small range of values.