• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.4
• /
• pp.616-624
• /
• 2018

In this study, a previous DNPH (2,4-dinitrophenylhydrazine) coupled with high performance liquid chromatography (HPLC) method to measure the concentration of formaldehyde in ambient and source environments has been improved. To improve the disadvantage of the previous HPLC method, an appropriate composition ratio of mobile phase (water: acetonitrile (ACN)) was determined and an isocratic analysis was conducted. Furthermore, limit of detection (LOD), limit of quantitation(LOQ), accuracy, and precision were investigated to verify the reliability of the analytical conditions determined. Finally, samples of exhaust gases from five different industrial facilities were applied to HPLC analytial method proposed to determine their formaldehyde concentrations. The appropriate composition ratio of the mobile phase under the isocratic condition was a mixture of water(40%) and ACN(60%). As the volume fraction of the organic solvent ACN increases, retention time of the formaldehyde peak was reduced. Detection time of formaldehyde peak determined using the proposed isocratic method was reduced from 7 minutes(previous HPLC method) to approximately 3 minutes. LOD, LOQ, accuracy, and precision of the formaldehyde determined using standard solutions were 0.787 ppm, 2.507 ppm, 93.1%, and 0.33%, respectively, all of which are within their recommended ranges. Average concentrations of the formaldehyde in five exhaust gases ranged from 0.054 ppm to 1.159 ppm. The lowest concentration (0.054 ppm) was found at samples from waste gas incinerator in a bisphenol-A manufacturing plant. The highest was observed at samples from the absorption process in manufacturing facilities of chemicals including formaldehyde and hexamine. The analytical time of the formaldehyde in ambient air can be shortened by using the isocratic analytical method under appropriate mobile phase conditions.

• Applied Chemistry for Engineering
• /
• v.27 no.1
• /
• pp.62-67
• /
• 2016

In this study, a pellet-type adsorbent was prepared by using the water-treatment sludge as a raw material, and its physical and chemical properties were analyzed through $N_2$-adsorption, XRD, XRF, and $NH_3$-TPD measurements. Adsorption performance for gaseous ammonia and formaldehyde was compared between the pellet-type adsorbents prepared from water-treatment sludge and the impregnated activated carbon. Although the surface area and pore volume of the pellet-type adsorbent produced from water-treatment sludge were much smaller than those of the impregnated activated carbon, the pellet-type adsorbent produced from water-treatment sludge could adsorb ammonia gas even more than that of using the impregnated activated carbon. The pellet-type adsorbent prepared from water-treatment sludge showed a superior adsorption capacity for ammonia which can be explained by chemical adsorption ascribed to the higher amount of acid sites on the pellet-type adsorbent prepared from water-treatment sludge. In the case of formaldehyde adsorption, the impregnated activated carbon was far superior to the adsorbent made from the water-treatment sludge, which can be attributed to the increased surface area of the impregnated activated carbon.

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.2
• /
• pp.259-266
• /
• 2006

A dual-channel glass coil sampling technique was used to measure hourly formaldehyde concentration in the ambient air. The dual-channel coil sampling assembly consists of three parts; an all-pyrex 28-turn coil made of 0.2-cm internal diameter glass tubing for gas-liquid contact and scrubbing of soluble gases, an inlet section upstream of the coil for introducing sample air and scrubbing solution, and a widened glass section downstream of the coil for gas-liquid separation. The scrubbing solution used was a dilute aqueous DNPH (dinitrophenylhydrazine) solution. Hourly concentration of formaldehyde was determined at a Gwangju semi-urban site during two intensive studies between September and October using the dual channel glass-coil/DNPH sampling technique and HPLC (High Performance Liquid Chromatography) analysis. The mean concentration was 1.7($0.4{\sim}4.7$) and 3.0($0.5{\sim}19.1$) ppbv for the September and October intensives, respectively, which are considerably low, compared to those measured in polluted urban areas around the world including several urban areas of Korea. The diurnal variation showed significant increase of formaldehyde in the daytime suggesting the dominance of formation of formaldehyde due to photochemical oxidation of methane and other hydrocarbons. An increase in the formaldehyde sometimes in the night might be due to an increase in primary source, i.e. traffic emissions. It was also found that rapid increase in formaldehyde levels from 3.0 to 19.1 ppbv in the afternoon on October 20 was due to plumes from burning of agricultural wastes such as rice straw and stubble. It is expected from the measurement data that the constructed dual-channel glass coil sampling system can be utilized for measuring atmospheric concentration of the formaldehyde with high time resolution.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.89-94
• /
• 1991

In the quantitative analysis of oxygenated exhaust emissions (unburned methanol, formal- dehyde) from methanol fueled vehicles, the oxygen contained in oxygenated exhaust gases lowers the FID (Flame Ionization Detector) response factor of conventional THC analyzer and leads to erroneous HC reading. For correct measurement of various HCs including oxygenated HCs emitted from FFV(Flexible Fuel Vehicle), first of all, the measurement technique of real HC emissions should be established. GC and HPLC-DNPH measuring methods specified by the EPA are used in this paper to analyze unburned methanol and formaldehyde components in the exhaust emissions. In emission test of FFV, unburned methanol and formaldehyde are emitted mostly during cold transient period, and it is shown that formaldehyde emission level is proportional to engine displacements. In view of the HC emission level, vehicle using M85 has 40% advantage over gasoline-fueled vehicle in OMHCE and has a good potential of a low emission vehicle.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.4
• /
• pp.43-49
• /
• 1996

With the recent interest in methanol as a SI engine fuel, aldehyde emissions have become a greater concern. A M-90 fueled passenger car was operated in a chassis dynamometer using FTP 75 driving cycle to examine formaldehyde emissions. Formation process of aldehyde and methods to reduce them are discussed in this paper for a SI-engine passenger car operating by M-90. Aldehyde emissions have been found to be 3 to 7 times higher from M-90 than from gasoline, while CO, NOx, THC are as low or lower than gasoline. Noble metal compositions appeared to play a role in formaldehyde and unburned methanol emission performance. For example, catalyst Pd showed better reduction of both formaldehyde and methanol than catalyst Pt. however, emission rates of formaldehyde and methanol for catalyst Pt were relatively similar to catalyst Pt/Rh.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.8
• /
• pp.1103-1105
• /
• 2002

H-ZSM-5 and γ-alumina were treated with formaldehyde and sodium carbonate. The treatment increased the amounts of weak acid sites, removing strong acid sites. The maximum temperature of weak acid sites in their ammonia TPD spectra shifted in the direction of high temperature. The modified H-ZSM-5 and g-alumina were mixed with the methanol synthesis catalyst to perform dimethyl ether synthesis from syn-gas. The modified catalysts showed better selectivity to dimethyl ether, minimizing the reforming reaction to carbon dioxide. The maximum yield of 53.3% to dimethyl ether was achieved under the reaction conditions of 54.4 atm, 523 K, and the feed rate of 4500 Lhr-1 .gcat-1.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.6
• /
• pp.83-88
• /
• 2003

The woodceramics are porous amorphous carbon and glassy carbon composite materials. Woodceramics attracted a lot of attention in recent years because they are environmentally friendly and because of their unique functional characteristics such as catalysis, moisture absorption, deodorization, purification, carrier for microbial activity, specific stiffness, corrosion and friction resistance, and their electromagnetic shielding capacity. In this paper, we made new products of clay-woodceramics to investigate the industrial analysis and ethylene gas adsorption for basic data of building- and packging- materials keeping fruit fresh for a long time. Clay-woodceramics were carbonized for 3 h of heating in a special furnace under a gas flow of nitrogen(15 ml/min.) from 3 layers-clay-woodparticleboard made from pallet waste wood, phenol- formaldehyde resin(hereafter PF, Non volatile content:52%, resin content 30%), and clay(10%, 20% and 30%). Carbonization temperature was 400℃, 600℃ and 800℃. Experimental results shows that the higher the carbonization temperature, the higher the fixed carbon and the lower the volatile contents. The higher the clay content, the more the ash content. The higher the carbonization temperature, the more the ethylene gas adsorption. Carbonization temperature of 800℃ gave the best reslts as same as that of white charcoal and activated carbon.(800℃-clay-woodceramic: 5.36 ppm, white charcoal: 5.66 ppm, activated carbon: 5.79 ppm) The clay contents did not make difference of ethylene gas adsoption.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.1
• /
• pp.29-34
• /
• 2008

The charcoal has been used not only as fuel but also as human health care material since it was used. Charcoal's performances were generally investigated in aspects of energy efficiency and caloric values. This study was conducted in order to increase charcoal's application area and to develop functional paper. Five types of charcoal were used on a basis of gas absorption properties from previous study. Handsheets were made by two methods by internal loading and surface spray on interlayer. Strength properties of internal loading and interlayer spray handsheets were decreased as the charcoal loading increased. Ethylene gas absorption property was higher in both of oak's black charcoal and white charcoal than others. In terms of strength, 5-10% charcoal loading was efficient. Above 10% loading, a rate of strength decrease was higher than that of ethylene gas absorption rate. Formaldehyde absorption property was higher at both of oak's black charcoal and mixed charcoal than others. However, to guarantee enough charcoal loading should be higher than 95 $g/m^2$ for sufficient formaldehyde absorption.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2005.11a
• /
• pp.550-551
• /
• 2005

• Journal of Conservation Science
• /
• v.31 no.3
• /
• pp.287-298
• /
• 2015

The formaldehyde is damage to the metal are known universally. However, the quantification of the damage level and degree of damage is not clear. This study was conducted to test the following steps using a gas corrosion tester, and then evaluated by the optical, chemical and physical measurement. First, it was confirmed the damage level of the metal specimen(silver, copper, iron, lead, brass) by the formaldehyde(0.5, 1, 10, 100, 500ppm). Second, weighted damage to the metal specimens were tested according to the temperature and humidity conditions under damage levels. Third, the damage of accelerated degradation metal specimens were examined under damage levles. As a result, at 500ppm / day, the optical, chemical and physical damage of lead have been identified, the optical damage of all metals are was observed. The optical damage of some specimens were weighted in $25^{\circ}C-50%$, $30^{\circ}C-50%$. Chemical damage to the lead specimen is 2.8 times, 1.3 times were weighted in $30^{\circ}C-80%$, $25^{\circ}C-80%$. Referring to formate ion concentration of the accelerated degradation metal, corrosion products of iron and brass were actived the reaction of the formaldehyde gas, oxide film of lead was blocked the reaction of formaldehyde gas.