• 한국공간구조학회논문집
• /
• 제17권1호
• /
• pp.77-84
• /
• 2017

Vortex-induced vibration and instability vibration of tall buildings are very important fluid-structure interaction phenomenon, and many fundamental questions concerning the influence of body movement on the unsteady aerodynamic force remain unanswered. For tall buildings, there are two experimental methods to investigate the characteristics of unsteady aerodynamic forces, one is forced vibration method and the other is free vibration method. In the present paper, a free vibration method was used to investigate the unsteady aerodynamic force on tall building whose aspect ratio is 9 under boundary layer simulating city area. Wind pressures on surfaces and tip displacements were measured simultaneously, and the characteristics of tip displacements and generalized forces were discussed. It was found that variation of across-wind displacements showed different trend between the case when wind speed increases and wind speed decreases, and the fluctuating generalize forces in across-wind direction of vibrating model are larger than that of static model near the resonant wind speed and approach to the static value. And for higher wind speed range, there were two peaks in across-wind power spectra of generalize forces of vibrating model, which means that two frequency components are predominant in unsteady aerodynamic forces.

• 대한기계학회논문집B
• /
• 제20권7호
• /
• pp.2277-2288
• /
• 1996

This study was performed to analyze the cooling effect of heated ribs which are frequently used for cooling of electronic parts, using the numerical method. To prevent the excessive pressure drop due to turbulence promoters for the enhancement of heat transfer rate especially, the effect of the angle of turbulence promoter was investigated by the numerical analysis. Heat transfer rate with turbulence promoters with rectangular cross-section increased by 13% in average, but the coefficient of pressure drop increased by 1.68 times than that without them. In the present study, triangular cross-sectional shape turbulence promoters were suggested and numerically tested. Pressure drop of turbulence promoter with the 30 degree triangular cross-sectional shape decreased by 30% from that of rectangular cross-section promoters while heat transfer rate was almost the same. While with 4 turbulence promoters, the heat transfer rate increased by 21%, the pressure drop increased 4 times. It means that the higher capacity of cooling fan should be needed. With the triangular cross-sectional shape, the size of vortex region at the rear of promoters became considerably smaller, so pressure drop became smaller. The effect of the change of cross-sectional shape was not found in the flow pattern near the ribs, so that heat transfer characteristics in the ribs were not changed.

• 한국정밀공학회지
• /
• 제17권10호
• /
• pp.155-161
• /
• 2000

Recently, environmental pollution has become a big problem in industry and many researches have been done in order to preserve the environment. In the grinding process, the coolant has great influence on environment. It contains several chemicals(sulfur, phosphorus and chlorine) to improve the grinding efficiency. If these additives go into the workplace atmosphere, it is harmful for workers. It can also cause the environment pollution. Because of these reasons many studies have been done to minimize the amount of coolant. However the small amount of coolant can cause the thermal defect on the ground surface layer. This study forced the effects of the compressed cold air when the spindle shaft materials(SCM4 & SCM21) were cylindrical ground with WA wheel. The compressed cold air was used as the coolant and grinding performance was compared with that of the conventional grinding fluids(emulsion). Many experiments were carried out with these two cooling materials. The surface roughness, residual stress, and roundness were measured for the cylindrical grinding. The test results showed that the compressed cold air was very useful as the cooling materials for grinding process. It was also efficient to minimize the thermal defects of workpiece and could also play a role in solving environmental pollution.

• 한국해안·해양공학회논문집
• /
• 제31권4호
• /
• pp.209-220
• /
• 2019

해빈 안정화를 위해 거치되는 강성 구조물의 규모는 해빈의 자기 치유 능력이 구현되는 해빈 대순환 과정이 훼손되지 않는 범위에서 결정되어야 하나 최근 지나치게 대형화 되어 광폭 잠제도 빈번하게 차용되고 있는 실정이다. 이러한 시각에 기초하면 Irie et al.(1994)가 제안한 왜도 된 연흔모양 매트는 규모가 크지 않다는 점에서 현재 선호되는 광폭잠제의 대안이 될 수 있을 것으로 판단된다. 전술한 왜도 된 연흔모양 매트의 해빈 안정화 효과는 매트의 유수 단면 축소부에서 강제되는 와류가 run-down 시 외해방향으로 이송되는 표사를 얼마나 효과적으로 포획할 수 있느냐에 따라 결정되는 것으로 추정된다. 본 논문에서는 이러한 가설을 확인하기 위해 수치모의를 수행하였다. 수치모형은 Navier-Stokes 식과 물리기반 지형모형으로 구성하였으며, 모의 결과 왜도 된 연흔모양 매트 정점부에서 강제된 와류에 의해 포획된 표사가 해안 방향으로 이송되는 등 왜도 된 연흔모양 매트의 해빈 안정화 효과를 구성하는 주요 기작과 해빈 안정화 효과를 확인할 수 있었다.