• 한국추진공학회지
• /
• 제24권3호
• /
• pp.18-30
• /
• 2020

본 연구는 고체추진기관의 추력측정불확도 추정 방법에 관한 것이다. 힘 측정불확도 추정 지침은 ISO와 국내외 기구에서 제공하고 있으나 모든 내용이 실험실에서 운용하는 하중시험기와 하중 센서의 교정을 중심으로 기술되고, 개념적으로 기술되어 있다. 추력시험대 불확도의 주요 원인인 교정식과 선형화 불확도의 추정에 대해서는 해당 지침을 직접 적용할 수는 없다. 본 논문에서는 측정불확도 기본 개념을 이용하여 교정식 불확도와 교정식의 선형화 불확도를 추정하는 식을 만들고, 이를 추력 시험대의 추력측정불확도에 추정하여 적용하였으며, 비교적 간단한 추력측정불확도 추정 방법을 제안하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.837-841
• /
• 2001

The column-type sensing element in building and mechanical construction parts was designed as three forces and three moments sensor by attaching strain gages approximately. Compared to conventional multi-component sensor, the designed sensor can solve the problem about low stiffness and high cost. The radius of the column was designed analytically and compared with finite element analysis. The coupling errors between components were minimized by using addition and subtraction procedure of signals. The fabricated sensor was tested by using a deadweight force standard machine and a six-component force calibration machine in Korea Research Institute of Standards and Science(KRISS). The calibration showed that the multi-component force/moment sensor had coupling error less than 19.8 % between $F_x$ and $M_y$ components, and 9.0 % in case of other components.

• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.47-52
• /
• 2008

The force transducer in the acceleration plant due to dynamic fracture is calibrated by dynamically using the stress pulses from a longitudinal bar. The bar is supported by two strings attached to the ceiling. The bar velocities before and after impact are measured and a full bridge at bar and transducer is formed by the four strain gauges. A transient recorder is used to store the stress pulse signals of force transducer and bar. For the first test series, three point bend test specimens can be chosen by means of test rig design and the inspection as sample experiment in this presented paper is sufficient for proving with the numerical simulation of the specimen model.

• 센서학회지
• /
• 제12권6호
• /
• pp.258-264
• /
• 2003

본 연구에서는 영상처리를 통한 부액계의 교정방법을 연구한다. 이 방법은 부액계를 교정하기 위해 선정된 부액계의 측정눈금과 기준액체의 수평면을 교정자의 조작 없이 자동으로 일치시킨다. 이 시스템은 CCD카메라, frame grabber, 스텝모터, 영상처리를 포함한 시스템프로그램으로 구성된다. 영상처리프로그램은 부액계의 측정눈금부위와 기준액체의 수평면사이에서 발생하는 메니스커스를 검색하여 눈금을 일치시키는 부분과 스텝모터를 제어하는 부분으로 구성한다. 본 연구에서 개발한 시스템의 성능을 검증하기 위하여 교정자의 눈으로 직접 메니스커스와 측정눈금을 관측한 수동교정방법의 교정결과와 비교한다 각각의 교정값의 차이가 $0.004\;kg/m^3$ 이하로서 교정값의 측정 불확도 $0.06\;kg/m^3$을 고려하면 두 방법의 교정결과가 거의 같은 연구결과를 얻었다.

• 소음진동
• /
• 제1권2호
• /
• pp.115-120
• /
• 1991

The impact hammer is extensively used in experimental modal analysis as a means to provide force over a broad range of frequencies. The hammer mass and the impact head are often changed to achieve a desired impact time duration with its corresponding input frequency spectrum, these mass changes affect the performance and sensitivity of the force transducer employed to measure the impact force. Both a mathematical model describing the effects of impact head and hammer mass on the performance of the force transducer and experimental verification of this model are presented here.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.709-710
• /
• 2010

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.711-712
• /
• 2010

• 대한기계학회논문집A
• /
• 제21권3호
• /
• pp.477-484
• /
• 1997

This paper describes the build-up force measuring system of 9.9 MN capacity which consists of nine force transducers of each having 1.1 MN capacity. We have specially designed a force transducer for a build-up force measuring system to reduce the uncertainty of a build-up system and to accomodate the new test procedure for a build-up system. It reveals that the relative uncertainty of the force measuring system is less than 1.5*10$^{-4}$ in the ran9e of 1-4.5 MN irrespective of loading direction. The force measuring system may be used to calibrate a 10 MN force standard machine to be used as a large force standard in Korea.

• 한국정밀공학회지
• /
• 제20권8호
• /
• pp.39-46
• /
• 2003

Productivity and machining performance can be improved by cutting analysis including cutting force prediction, surface error prediction and machining stability evaluation. In order to perform cutting analysis, cutting force coefficients database have to be constructed. Since cutting force coefficients are dependent on cutting condition in the existing research, a large number of calibration tests are needed to obtain cutting force coefficients, which makes it difficult to build the cutting force coefficients database. This paper proposes a generalized method for constructing the cutting force coefficients database us ins cutting-condition-independent coefficients. The tool geometry and workpiece material were considered as important components for database construction. Cutting force coefficients were calculated and analyzed for various helix and rake angles as well as for several workpiece. Furthermore, the variation of cutting force coefficients according to tool wear was analyzed. Tool wear was found to affect tool geometry, which results in the change of cutting force coefficients.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.27-28
• /
• 2009

건축물의 지진모의실험을 수행할 경우, 부재에 작용하는 전단력과 축력의 계측이 필요하다. 본 연구에서는 2축 전단, 1축 압축을 측정할 수 있는 Load Cell의 제작 및 Calibration법을 제시하고 있다.