• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.512-514
• /
• 2008

In this paper, a new electromagnetic circuit is proposed for an optical pickup actuator with high sensitivity. Contrary to those of conventional actuators, the proposed circuit has two focusing coils which are diagonally placed at the front and rear of a moving part. The configuration which makes the effective length of the focusing coil longer and the moving part lighter, is helpful in increasing the sensitivity of the actuator. However, the asymmetry of the moving part by two focusing coils causes flexible node vibrations in quite low frequency range. This paper shows that the design modification of the moving part for the reconfiguration of mass moment of inertia can reduce the mode vibrations.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.744-749
• /
• 2005

In this paper, a lens actuator for mobile devices is proposed using stack type piezoelectric materials. In general, the deformation of PZT actuators is not enough for lens motion when the allowed voltage is applied. The small stroke problem can be solved by accumulating a lot of small displacements in high frequency. In this paper, a new inch-worm type model for focusing actuator is suggested based on the interaction of inertial and frictional forces. Theoretical analysis and simulation using ANSYS are performed to verify the feasibility of the inch-worm PZT actuator model. Various types of clamps are considered to determine the effect of frictional force on the motion, and appropriate clamp-actuator models are proposed. The proposed models are experimentally verified and the experimental results show high correspondence with theoretical and simulated values. The inch-worm type focusing actuator enable a large stroke with 7.79 mm/sec with 10kHz and 10V.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.136-139
• /
• 2006

In this paper we propose a small form factor actuator using an inclined motion guide for auto-focusing and zoom motions for mobile information devices. The novel structure using the inclined motion guide and a lens-supporting beam converts the circular motion by an ultrasonic motor into the linear motion of the optical lens. The proposed actuator has a simple structure to minimizing the mechanical tolerance, and the stroke is easy to modify by controlling the inclined angle. Experiments using a prototype verify the validity of the model as small form factor optical actuator.

• 한국소음진동공학회논문집
• /
• 제21권3호
• /
• pp.227-233
• /
• 2011

The ultrasonic guided wave phased array using magnetostrictive patch transducers is proposed. The magnetostrictive transducer has received much attention because it is cost-effective and capable to generate ultrasonic waves with a simple configuration. However, it has not been used for ultrasonic guided wave phased array applications until now. In this paper, we propose a magnetostrictive transducer based phased array system consisting of a multi-channel function generator, power amplifiers and Lamb wave magnetostrictive transducers. To check the performance of the ultrasonic guided wave phased array, several Lamb wave focusing experiments were carried out in an aluminum plate. The results demonstrated the capability of the developed array to focus the Lamb waves at specific target points.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.1101-1106
• /
• 2003

As the disk in the ODD rotates, disturbances acting on the ODD servo system generally have periodic components. Such disturbances can make the system unstable and make the controller hard to work. The repetitive controller can be the solution of the periodic disturbances by making the periodic control signals. In this paper repetitive controller is proposed that make the control signal follow the periodic disturbances. A low pass filter, which can make the system stable, is proposed by the simple stability conditions. We will show the performance of the repetitive controller in actual commercial system. Simulation and experimental results will be given as the evidences

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.438-444
• /
• 1997

Recently, optical disk drives are increasingly demanded to have higher speed as well as high information density, especially for applications like CD-ROM drives. To this end, improvement of their optical pick-up structure and control is recognized the very challenging issue. In this paper, the 2-D motion of the pick-up is first analytically modelled to identify the cause and effect of the troublesome cross coupling between auto-focusing and tracking directions. Subsequently, the overall system equations are derived to include the dynamics of the related components in the auto-focusing servo system. While its unmeasurable parameters being estimated by the least square error method, a simple but decent linear model can be obtained within its operating frequency range. To design the high speed and robust positional servo controller, the design specifications are detailed and H$\sub$.inf./ control method is employed based on the simple model. Using the pickup in a commercial 8 fold speed CD-ROM drive as an example, performance of the designed controller is verified by realtime experiments.

• 대한기계학회논문집A
• /
• 제33권1호
• /
• pp.1-26
• /
• 2009

Cylindrical shells of isotropic and composite laminated materials are being used many engineering applications. This paper reviews the literature focusing on various aspects of shell research. The aspects of research receiving interest here are the cylindrical theory being used, the stress, buckling analysis and the impact analysis. The vibration analyses and stiffening characteristics of the cylindrical shell are investigated. The design optimizations of the cylindrical shell are reviewed. The studies on the conical and spherical shell are also reviewed. This review aticles contain 236 referencees.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.786-790
• /
• 2001

In this paper, we propose an optimum design method for optical pick-up actuators. Using this method, we can design an optimal pick-up actuator having the required tracking/focusing performances. Also, the designed actuator has the small mass, force constant for small size of magnetic circuit and large resistance for reduction of heat generation. Simulation results show that this method can be potentially implemented in all the pick-up actuators.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.232-235
• /
• 2004

• 한국소음진동공학회논문집
• /
• 제23권6호
• /
• pp.537-545
• /
• 2013

In this paper, the vibration for actuators having lens module, confined to lateral and torsional directions of suspensions, is described by mathematically analyzing its suspension configuration and motion. In order to prove the accuracy of this result, it is compared to a finite element analysis. Also it is shown that modal frequencies can be modified by changing design parameters in mathematical motion expressions.