• International Journal of Automotive Technology
• /
• v.2 no.2
• /
• pp.39-45
• /
• 2001

Hydrogen is seen as one of the important energy vectors of the next century. Hydrogen as a renewable energy source, provides the potential for a sustainable development particularly in the transportation sector. Hydrogen driven vehicles reduce both local as well as global emissions. The laboratory of transporttechnology (University of Gent) converted a GM/Crusader V-8 engine for hydrogen use. Once the engine is optimised, it will be built in a low-floor midsize hydrogen city bus for public demonstration. For a complete control of the combustion process and to increase the resistance to backfire (explosion of the air-fuel mixture in the inlet manifold), a sequential timed multipoint injection of hydrogen and an electronic management system is chosen. The results as a function of the engine parameters (ignition timing. injection timing and duration, injection pressure) we given. Special focus is given to topics related to the use of hydrogen as a fuel: ignition characteristics (importance of electrode distance), quality of the lubricating oil (crankcase gases with high contents of hydrogen), oxygen sensors (very lean operating conditions), noise reduction (configuration and length of inlet pipes). The advantages and disadvantages of a power regulation only by the air to fuel ratio (as for diesel engines) against a throttle regulation (normal gasoline or gas regulation) are examined. Finally the goals of the development of the engine are reached: power output of 90 kW, torque of 300 Nm, extremely low emission levels and backfire-safe operation.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.4
• /
• pp.1555-1570
• /
• 2016

For monitoring forest fires, a real-time system to prevent fires in wider areas should be supported consistently. However, there has still been a lack of the support for real-time system related to forest fire monitoring. In addition, the 'real-time' processing in a forest fire detection system can lead to excessive consumption of energy. To solve these problems, the intelligent data acquisition of sensing nodes is required, and the maximum energy savings as well as rapid and accurate detection by flame sensors need to be done. In this regard, this paper proposes a node built-in filter algorithm for intelligent data collection of sensing nodes for the rapid detection of forest fires with focus on reducing the power consumption of the remote sensing nodes and providing efficient wireless sensor network-based forest environment monitoring in terms of data transmission, network stability and data acquisition. The experimental result showed that battery life can be extended through the intelligent sampling of remote sensing nodes, and the average accuracy of the measurement of flame detection based on the distance is 44%.

• Journal of Internet Computing and Services
• /
• v.2 no.4
• /
• pp.91-99
• /
• 2001

Since roost of the program execution time is spent in the loop structure, the problem of extracting parallelism from sequential loop has been one of the most important research issues. However. roost programs have Implicit interprocedure parallelism. This paper presents a generalized method extracting parallelism in loops having the procedure calls. Most parallelization of loops having procedure calls focus on the uniform code where data dependency distance is constant. We present algorithms which can be applied to uniform code, nonuniform code, and complex code. The performance of the proposed algorithm, loop extraction, loop embedding and procedure cloning transformation methods have been evaluated using CRAY-T3E. The result shows the effective of the proposed algorithm.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.4
• /
• pp.74-78
• /
• 2008

High-speed tool steels are extensively used in tooling industries for manufacturing cutting tools, forming tools, and rolls. Electrical discharge machining (EDM) has been found to be an effective process for machining these extremely hard and difficult-to-cut materials. Extensive research has been conducted to identify the optimum machining parameters for EDM with different tool steels. This paper presents a fundamental study of the surface characteristics of SKH-51 tool steel machined by micro-EDM, with particular focus on obtaining a better surface finish. An RC pulse generator was used to obtain a better surface finish as it produces fine discharge craters. The main operating parameters studied were the gap voltage and the capacitance while the resistance and other gap control parameters were kept constant. A negative tungsten electrode was used in this study. The micro-EDM performance was analyzed by atomic force microscopy to determine the average surface roughness and the distance between the highest peak and lowest valley. The topography of the machined surface was observed using a scanning electron microscope and a digital optical microscope.

• Current Optics and Photonics
• /
• v.1 no.4
• /
• pp.315-324
• /
• 2017

In recent years, multicast services such as high-definition television (HDTV), video conferencing, interactive distance learning, and distributed games have increased exponentially, and wavelength-division multiplexing (WDM) networks are considered to be a promising technology due to their support for multicast applications. Multicast survivability in WDM networks has been the focus of extensive attention since a single-link failure in an optical network may result in a massive loss of data. But the improvement of network survivability increases energy consumption due to more resource allocation for protection. In this paper, an energy-efficient multicast algorithm (EEMA) is proposed to reduce energy consumption in WDM networks. Two cost functions are defined based on the link state to determine both working and protection paths for a multicast request in WDM networks. To increase the number of sleeping links, the link cost function of the working path aims to integrate new working path into the links with more working paths. Sleeping links indicate the links in sleep mode, which do not have any working path. To increase bandwidth utilization by sharing spare capacity, the cost function of the protection path is defined to use sleeping fibers for establishing new protection paths. Finally, the performance of the proposed algorithm is evaluated in terms of energy consumption, and also the blocking probability is evaluated under various traffic environments through OPNET. Simulation results show that our algorithm reduces energy consumption while maintaining the quality of service.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.2 no.2
• /
• pp.112-118
• /
• 2010

The numerical study about the vortex-induced vibration and vortex shedding in the wake has been presented. Prior to the numerical simulation of flexible riser systems concerning engineering conditions, efficiency validating of the proposed FSI solution method have been performed. The comparison between numerical simulation and published experimental data shows that the CFD method designed for FSI solution could give acceptable result for the VIV prediction of flexible riser/pipe system. As meaningful study on VIV and vortex shedding mode with the focus on flexible riser model systems, two kinds of typical simulation cases have been carried out. One was related to the simulation of vortex visualization in the wake for a riser model subject to forced oscillation, and another was related to the simulation of fluid-structure interaction between the pipes of coupled multi-assembled riser system. The result from forced oscillation simulation shows that the vortex-induced vibration with high response frequency but small instantaneous vibration amplitude contributes to vortex conformation as much as the forced oscillation with large normalized amplitude does, when the frequency of forced oscillation was relatively high. In the multi-assembled riser systems, it has been found that the external current velocity and the distance between two pipes are the critical factors to determine the vibration state and the steady vibration state emerging in quad-pipe system may be destroyed more easily than dual-pipe system.

• Proceedings of the KWS Conference
• /
• 1996.10a
• /
• pp.139-141
• /
• 1996

Among various welding parameters, the welding current which is inversely proportional to the tip-to-workpiece distance in GMAW is an essential parameter to monitor the GMAW process of horizontal fillet joints. For the case of weld defect such as overlap in horizontal fillet welding, therefore, the signal processing for process monitoring or automatic seam tracking should be modified by considering the weld pool surface geometry including the corresponding weld defect. In other words, the adequate signal processing algorithm is indispensible to improve the performance of the arc sensor. However, arc sensor algorithm already developed usually focus on weld seam tracing but do not considering the weld qualities. In this paper, various experiments were carried out to investigate the tendencies of the weld defects when weaving motion is added, and the experimental method based on 2$^n$ factorial design was proposed for deriving the mathematical model between the leg length and the various welding conditions. Moreover, a signal processing method based on the artificial neural network(Adaptive Resonance Theory) was proposed far discriminating the current signal of sound weld beads from that of weld beads with overlap. Finally, the algorithm for weld seam tracking combined with the mathematical modeling and the signal processing method was carried out to track the weld line in conjunction with the improvement of the weld qualities. The reliability of the proposed algorithms were evaluated through various experiments, which showed that the proposed algorithms could be effectively used for arc welding automation.

• Journal of architectural history
• /
• v.7 no.2 s.15
• /
• pp.77-90
• /
• 1998

This study on the site of vision in the Villa Savoye of Le Corbusier, concentrates on the precise analysis of the meaning of 'fenetre on longueur' in the living room. A lots of architectural theorists have regarded the Villa Savoye of Le Corbusier as a symbol of modern architecture, and his 'fenetre on longueur' as products of modern technology. But Le Corbusier who defined himself as 'homme visuel', responded keenly to the vision conditions inherent to the human finitude, Indifferent to the modern technology, Such a response would be derived from the experience of Acropolis, where 'the scheme was designed to be seen from a distance.' Generally speaking, 'fenetre en longueur', contra to 'porte-fenetre', makes one to focus on the panorama effect of the horizon, including a distant view. Entering the living room of Villa Savoye, however, we may perceive this window in two ways. Firstly this window acts as a screen to obstruct not to see outside, because of the wall above pressing down the line of view. Secondly this acts as a frame to make us see a distant view as far as eye can reach. These two ways result in the abbreviation of near view, and a sudden shift between a inferiority(derived from 'screen effect') and a distant view(from 'frame effect'). Depending on such a observation, this study can evaluate 'fenetre en longueur' internalizing of a distant view as the highest compressed scene of Le Corbusier's architectural poetics.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.1
• /
• pp.207-210
• /
• 2013

We report the construction of a MALDI imaging mass spectrometer equipped with a specially designed laser focusing lens, a compact aspherical singlet lens, that obtains a high-lateral imaging resolution in the microprobe mode. The lens is specially designed to focus the ionization laser (${\lambda}$ = 355 nm) down to a $1{\mu}m$ diameter with a long working distance of 34.5 mm. With the lens being perpendicular to the sample surface and sharing the optical axis with the ion path, the imaging mass spectrometer achieved an imaging resolution of as good as $5{\mu}m$ along with a high detection sensitivity of 100 fmol for peptides. The mass resolution was about 900 (m/${\Delta}m$) in the linear TOF mode. The high-resolution capability of this instrument will provide a new research opportunity for label-free imaging studies of various samples including tissues and biochips, even for the study at a single cell level in the future.

• Nuclear Engineering and Technology
• /
• v.49 no.4
• /
• pp.865-872
• /
• 2017

For more than 10 years, the laser process has been studied for dismantling work; however, relatively few research works have addressed the effect of high-power fiber laser cutting for thick sections. Since in the nuclear sector, a significant quantity of thick material is required to be cut, this study aims to improve the reliability of laser cutting for such work and indicates guidelines to optimize the cutting procedure, in particular, nozzle combinations (standoff distance and focus position), to minimize waste material. The results obtained show the performance levels that can be reached with 10 kW fiber lasers, using which it is possible to obtain narrower kerfs than those found in published results obtained with other lasers. Nonetheless, fiber lasers appear to show the same effects as those of $CO_2$ and ND:YAG lasers. Thus, the main factor that affects the kerf width is the focal position, which means that minimum laser spot diameters are advised for smaller kerf widths.