• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.5
• /
• pp.437-445
• /
• 2016

Recently, polyurethane foam has been used in various industry fields to preserve temperature environment of structures, and a wide range of loads from the static to the dynamic are imposed on the material during a life period. The biggest characteristic of polyurethane foam is porosity as being polymeric material, and it is generally known that insulation performance of the material strongly depends on internal void size. In addition, polyurethane foam's mechanical behavior has high dependence on strain rate and temperature as well as being highly non-linear ductile for compression. In the non-linear compressive behavior, volume fraction of voids and elastic modulus decrease as strain increases. Therefore, in this study, temperature-dependent viscoplastic-damage constitutive model was developed to describe the non-linear compressive behavior with the aforementioned features of polyurethane foam.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.5
• /
• pp.543-551
• /
• 2015

Polyurethane Foam(PUF), a outstanding thermal insulation material, is used for various structures as being composed with other materials. These days, PUF composed with glass fiber, Reinforced PUF(R-PUF), is used for a insulation system of LNG Carrier and performs function of not only the thermal insulation but also a structural member for compressive loads like a sloshing load. As PUF is a porous material made by mixing and foaming, mechanical properties depend on volume fraction of voids which is a dominant parameter on density. Thus, In this study, density is considered as the effect parameter on mechanical properties of Polyurethane Foam, and mechanical behavior for compression of the material is described by using modified Gurson damage model.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.202-209
• /
• 2019

The objective of this study is to examine the reproducibility for compressive strength development and mechanical properties of lightweight concrete made using bottom ash aggregates and foam(LWC-BF). Based on the mix proportions conducted by Ji et al., six identical mixes were prepared with different actual foam volume ratios from 0% to 25% and water-to-binder ratios from 25% to 30%. The presently measured properties, including initial slump, slurry density, compressive strength gains at different ages, splitting tensile strength, and modulus of rupture, were very close to those determined in the previous tests by Ji et al. Thus, the developed LWC-BF has a good potential in obtaining a reproducibility for compressive strength development and mechanical properties even though the troubles of mixing control owing to the addition of preformed foam.

• Applied Chemistry for Engineering
• /
• v.17 no.1
• /
• pp.82-86
• /
• 2006

When a domestically manufactured floater is used in a general gasoline or LPG car, or a flowmeter is floated long time in the engine oil under above $150^{\circ}C$, the floater will be swelled or its organization will be slackened because weight and volume will be changed due to the osmosis of fuel. In this study, we conducted a research on a manufacturing technique of a foam-floater with the small changse in weight and volume, oil-resistance, and thermal resistance in the high temperature engine oil. When the prepared floater TROF II-3, where Nitrile Butadiene Rubber (NBR) as basic material of the floater was superseded by Hydrogenated Nitrile Butadiene Rubber (HNBR), was floated for 100 h at the engine oil of high temperature ($150^{\circ}C$), the change rates of the weight and the volume were 2.90%, and 2.56%, respectively. These were less than the NBR (TROF I-3) case, where the change rates of the weight and the volume were 10.81% and 3.08%, respectively, Therefore, TROF II-3 was determined to be suitable as an engine-oil floater in high temperature because the change of weight and volume were small, the appearance, and the specific gravity of floater were maintained uniformly in the high temperature.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.04a
• /
• pp.67-72
• /
• 2003

• Journal of Powder Materials
• /
• v.21 no.4
• /
• pp.266-270
• /
• 2014

Metal foams have a cellular structure consisting of a solid metal containing a large volume fraction of pores. In particular, open, penetrating pores are necessary for industrial applications such as in high temperature filters and as a support for catalysts. In this study, Fe foam with above 90% porosity and 2 millimeter pore size was successfully fabricated by a slurry coating process and the pore properties were characterized. The Fe and $Fe_2O_3$ powder mixing ratios were controlled to produce Fe foams with different pore size and porosity. First, the slurry was prepared by uniform mixing with powders, distilled water and polyvinyl alcohol(PVA). After slurry coating on the polyurethane(PU) foam, the sample was dried at $80^{\circ}C$. The PVA and PU foams were then removed by heating at $700^{\circ}C$ for 3 hours. The debinded samples were subsequently sintered at $1250^{\circ}C$ with a holding time of 3 hours under hydrogen atmosphere. The three dimensional geometries of the obtained Fe foams with an open cell structure were investigated using X-ray micro CT(computed tomography) as well as the pore morphology, size and phase. The coated amount of slurry on the PU foam were increased with $Fe_2O_3$ mixing powder ratio but the shrinkage and porosity of Fe foams were decreased with $Fe_2O_3$ mixing powder ratio.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.30 no.1
• /
• pp.48-55
• /
• 2001

This study investigated the quality characteristics of sponge cakes with addition of yam (Dioscorea) powders prepared by different drying methods, hot air (HDYP : hot air dried yam powder) and freeze drying (FDYP: freeze dried yam powder), using several physical and sensory examinations. For the foam forming ability and foam stability, the specific gravities of egg foams containing 5% yam powders were measured by drainage using funnels for 78 hrs. The results showed that HDYP and FDYP did not affect the foam forming ability but FDYP increased foam stability due to increased viscosity. When the strength of 8% gels composed of wheat starch and HDYP/FDYP was measured to predict the setting of cake structure, the strengths of starch gels containing yam powders were higher than those of control without yam powders. The volume of sponge cake containing 5% HDYP increased whereas those containing FDYP decreased at the levels of 5, 7%. From the texture profile analysis data, hardness, gumminess and chewiness of cakes containing yam powders increased. The color of cake crust and crumb became darker as the amount of yam powders increased. The results of sensory evaluation by QDA (quantitative descriptive analysis) to compare two different drying methods showed that appearance and texture of cakes containing 5% HDYP were closer to those of control than cakes containing 5% FDYP but overall acceptability of sponge cakes containing yams were comparable to the control cakes regardless of drying methods. The addition of yam powders to sponge cakes increased yam flavor and decreased egg smell. Therefore, it can be suggested that HDYP and FDYP can be added to the sponge cake formula up to 7% and 5%, respectively.

• Resources Recycling
• /
• v.26 no.6
• /
• pp.97-101
• /
• 2017

Metal foams have a cellular structure consisting of a solid metal containing a large volume fraction of pores. In particular, open pores which are penetrable pores are necessary for industrial applications such as in high temperature filters and as support for catalysts. In this study, Fe foam with greater than 90% porosity and 2-mm pore size was successfully fabricated using a slurry coating process and the pore properties were characterized. The Fe and $Fe_2O_3$ powder mixing ratios were controlled to produce Fe foam samples with different pore sizes and porosity. First, the slurry was prepared through the uniform mixing of powders, distilled water, and polyvinyl alcohol(PVA). The amount of slurry coated with the PU foam increased with increasing $Fe_2O_3$ mixing powder ratio, but the shrinkage and porosity of the Fe foams decreased, respectively, with increasing $Fe_2O_3$ mixing powder ratio.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.618-623
• /
• 2008

To enhancement heat transfer performance, the metallic foam as heat exchanger was studied rapidly. This was attributed to its high surface area to volume ratio as well as intensive flow mixing by tortuous flow passages. So the experimental study about the heat transfer characteristic of metallic foam is presented in this paper. The material in this experiment was used as FeCrAl which has density of 10 ppi, 20 ppi and 30 ppi respectively. And the results show the heat transfer is rise with permeability Reynolds number increase and the pressure drop metallic foam was increased with the ppi increase.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.1
• /
• pp.17-27
• /
• 2019

We carry out the numerical simulation to test a hypothesis that freak waves can be triggered by the infragravity waves of bound mode underlying the ever-present swells and its constructive interaction with swells using the Tool Box called the ihFoam that has its roots on the OpenFoam, and Bi-spectrum. Numerical simulation is implemented for the SamChcuk LNG Plant where freak waves have been reported in front of the private wharf during its construction phase due to the uncompleted northern breakwater. Infra-gravity waves of bound mode is generated using the difference wave-wave interaction between the local wind waves of 7 s and a swell of 11.4 s based on the Bi-spectrum. For the sake of comparison, numerical simulation for infra-gravity waves of free mode is also carried out. Numerical results show that stem waves along the private wharf for SamChcuk LNG Plant can be triggered by the infra-gravity waves of bound mode coming from the north, which eventually leads to freak waves when encounters the reflected waves from the south jetty.