• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.202-204
• /
• 1993

Appropriate control of real and reactive power flowing in and out from system can lead to considerable benefits : network stabilization, load leveling, voltage regulation etc. This paper presents how to control real and reactive power flow between an flywheel energy storage system and a power three phase network. The system compensating real and reactive power consists of control system and cycloconverter operating in the four quadrant modes.

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.7-11
• /
• 2002

This paper proposes an APF(Active Power Filter) with WRIM(Wounded Rotor Induction Motor) controlled by sliding mode which can compensate harmonic currents generated in a power system. As non-linear loads increase gradually in industry fields, harmonic current generated In the electric power network system also increases. Harmonic current makes a power network current distorted and generates heat, vibration and noise In the power machinery, Many approaches have been applied to compensate harmonic currents generated in the power system. Among various control strategy, in this paper, a sliding mode controlled systems is designed and evaluated. This is a flywheel compensator based on secondary excitation of WRIM(wounded rotor induction motor) with SMC(sliding mode controller). The proposed system uses a flywheel as an energy storage device. The designed control scheme is verified through simulation.

• Journal of Drive and Control
• /
• v.7 no.2
• /
• pp.33-41
• /
• 2010

• Tribology and Lubricants
• /
• v.27 no.3
• /
• pp.167-173
• /
• 2011

In this paper, an actuator model of the thrust magnetic bearing for the flywheel energy storage is derived using magnetic circuit theory. And we compared this result with finite element magnetic field analysis result. Based on the actuator model, we made a simulation model of the thrust magnetic bearing system. We showed the closed loop transfer function and sensitivity function of the thrust magnetic bearing system using both the simulation model and the experiment. The experimental result at rotation velocity 18,000rpm of thrust magnetic bearing system is included.

• Tribology and Lubricants
• /
• v.22 no.4
• /
• pp.196-202
• /
• 2006

This paper presents a case study on the tribological failure analysis of a clutch system for a manual transmission car. The clutch systems are composed of clutch disk, clutch pressure plate, flywheel rubbing surface, coil and diaphragm springs, release bearing and lever, clutch spline and shaft. The purpose of a clutch system is to transmit and disconnect the driving power of engines by frictional farce from a rubbing surface of a flywheel to a clutch disk and clutch pressure plate with a minimum power loss. In this study, many tribological failure cases based on the wear phenomena and thermal distortions have been presented, which are collected from the car repair shop and maintenance center. The triboiogicai failures are mostly come from the driving conditions, overloading of a car, and especially driving style and personal habit of a car driver.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.272-274
• /
• 1998

This paper treated the design and performance test of high speed motor/generator used in the flywheel energy storage system. The unique characteristics of the motor in this paper is the it doesn't contain any magnetic material. The field system was constructed by using Halbach array that generates the magnetic field with the permanent magnet only. The armature was also composed of plastic bobbin and winding. This paper shows the design results have a good agreement with the experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.433-441
• /
• 1999

This paper presents a S-FES(Superconducting magnetic becuing Flywheel Energy Storage System) for the p purpose of replacing battery used to store the energy. Especially, the design elements of FES, such as the b beming, wheel mateηaI, and power converter, etc., are described. The design and manufacturing techniques of t the controllable IXlwer converter are proposed to generate the sinusoidal output current in the high speed operation and to get the const빠synchronous motor with halbach cuTay of high coesive I\d-Fe-B permanent magnet is used as the driver of F FES. The proposed S-FES system shows the stable rotation characteristics at high speed range about l 10,000[rpm]. To verify the validity of proposed system, the comparative study with the conventional ball b beming s~rstem is proceeded and it is well confirmed with the result of the lower friction losses of S-FES S system.

• Progress in Superconductivity
• /
• v.11 no.1
• /
• pp.57-61
• /
• 2009

A superconductor flywheel energy storage(SFES) system is mainly act an electro-mechanical battery which transfers mechanical energy into electrical form and vice versa. SFES system consists of a pair of non-contacting High Temperature Superconductor (HTS) bearings with a very low frictional loss. But it is essential to design an efficient HTS bearing considering with rotor dynamic properties through correct calculation of stiffness in order to support a huge composite flywheel rotor with high energy storage density. Static properties of HTS bearings provide data to solve problems which may occur easily in a running system. Since stiffness to counter vibration is the main parameter in designing an HTS bearing system, we investigate HTS bearing magnetic force through static properties between the Permanent Magnet(PM) and HTS. We measured axial / radial stiffness and found bearing stiffness can be easily changed by activated vibration direction between PM and HTS bulk. These results are used to determine the optimal design for a 10 kWh SFES.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1442-1448
• /
• 2017

Recently, electric power systems have been operating with tight margins and have reached their operational limits. Many researchers consider a microgrid as one of the best solutions to relieve that problem. The microgrid is generally powered by renewable energies that are connected through power converters. In contrast to the rotational machines in the conventional power plants, the converters do not have physical rotors, and therefore they do not have rotational inertia. Consequently, a stand-alone microgrid has no inertia when it is powered by the only converter-based-generators (CBGs). As a result, the relationship between power and frequency is not valid, and the grid frequency cannot represent the power balance between the generator and load. In this paper, a superconducting flywheel energy storage system (SFESS) is applied to an inertia-free stand-alone (IFSA) microgrid. The SFESS accelerates or decelerates its rotational speed by storing or releasing power, respectively, based on its rotational inertia. Then, power in the IFSA microgrid can be balanced by measuring the rotor speed in the SFESS. This method does not have an error accumulation problem, which must be considered for the state of charge (SOC) estimation in the battery energy storage system (BESS). The performance of the proposed method is verified by an electromagnetic transient (EMT) simulation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.283-289
• /
• 2010

Owing to the increasing worldwide interest in green technology and renewable energy sources, flywheel energy storage systems (FESSs) are gaining importance as a viable alternative to traditional battery systems. Since the energy storage capacity of an FESS is proportional to the principal mass-moment of inertia and the square of the running speed, a design that maximizes the principal inertia while operatingrunning at the highest possible speed is important. However, the requirements for the stability of the system may impose a constraint on the optimal design. In this paper, an optimal design of an FESS that not only maximizes the energy capacity but also satisfies the requirements for system stability and reduces the sensitivity to external disturbances is proposed. Cross feedback control in combination with a conventional proportional-derivative (PD) controller is essential to reduce the effect of gyroscopic coupling and to increase the stored energy and the specific energy density.