• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.2163-2166
• /
• 2004

For designing high Tc superconductor proceeding bearing(HTSJB) which is used on a flywheel energy storage system which requests the free of the bearing loss caused by the friction, it is necessary to understand the basic characteristics of the classical superconductor proceeding bearing because the mechanical characteristics of the HTSJB are identified by the magnetic relationships between the permanent magnet(PM) and the high Tc superconductor(HTS). In this paper, using the method, frozen image model, the force problems between the PM and the HTS were solved and then the dynamic characteristics of the rotor inside of the HTSJB can be expected in advance by using the basic characteristics between the PM and the HTS. The coefficient of friction of the HTSJB was measured in the vacuum environment. From the results, the mechanical characteristics of HTSJB can be identified using the numerical models.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.304-306
• /
• 2014

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.495-497
• /
• 2013

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.9
• /
• pp.3135-3140
• /
• 2010

A 5 kWh composite flywheel rotor was designed and manufactured, and its spin test was performed to monitor strain distribution and burst speed. Strain distribution in radial and circumferential directions of the rotor were measured using a wireless telemetry system based on bluetooth technology for real-time strain measurement. The strains was compared with pre-calculated design values to verify the initial rotor design. We noticed the rotor failed at 19,499 rpm in the spin test, 11 % lower than the predicted burst speed of 22,000 rpm. Failure occurred at the hub which connects the shaft and the composite rotor. The performance of the composite rotor was confirmed in a general sense, and the danger of unexpected failure of composite rotor during high-speed spinning was also demonstrated in this paper. Special attention should be paid to not only composite rotor but also hub when designing a flywheel energy storage system. The telemetry system needs to be further developed, especially enduring the high centrifugal forces, and can be used in a real time monitoring system for the flywheel energy storage system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.433-441
• /
• 1999

This paper presents a S-FES(Superconducting magnetic becuing Flywheel Energy Storage System) for the p purpose of replacing battery used to store the energy. Especially, the design elements of FES, such as the b beming, wheel mateηaI, and power converter, etc., are described. The design and manufacturing techniques of t the controllable IXlwer converter are proposed to generate the sinusoidal output current in the high speed operation and to get the const빠synchronous motor with halbach cuTay of high coesive I\d-Fe-B permanent magnet is used as the driver of F FES. The proposed S-FES system shows the stable rotation characteristics at high speed range about l 10,000[rpm]. To verify the validity of proposed system, the comparative study with the conventional ball b beming s~rstem is proceeded and it is well confirmed with the result of the lower friction losses of S-FES S system.

• 한국초전도학회:학술대회논문집
• /
• v.13
• /
• pp.18-18
• /
• 2003

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.518-522
• /
• 2004

This paper describes a dynamic UPS system with flywheel energy storage element. There are three operating modes of charging, voltage compensation, and UPS. The operating principle of each mode is analyzed and simulated. The simulation results show the validity of the operation of the proposed scheme.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.3
• /
• pp.241-247
• /
• 2005

This paper deals with the operation of a flywheel energy storage UPS. The UPS has good features such as long life-time, improved efficiency, no environmental problems, reduced size and space, and low maintenance cost compared with the conventional UPS using battery. The operating principle of the UPS is analysed in each mode including voltage compensation as well as uninterruptible power supply. Especially, the tracking characteristic of the disturbed phase of the source voltage after outage is analysed. The usefulness of the system is proved through simulations and experiments.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1071-1077
• /
• 2000

Recently, several attempts have been made to apply high Tc superconductor bearings of thrust type to flywheel energy storage system (FESS) throughout the world. Radial type superconductor bearings, however, have never been tried to the real FESS. KEPRI has developed its own radial type bearings and is now currently applying them to a FESS designed by KIMM, for the first time. In this paper preliminary test results of bearing performance and dynamic behavior of the flywheel rotor system mounted on them are presented. The dynamic properties, i.e, stiffness and damping, of the superconductor bearings were experimentally estimated using the static loading test as well as the impact test. The test revealed that stiffness value of the present superconductor bearings is about 67,700N/m and the damping value 29Ns/m. It was also found out that these bearings have some levitation drift problems due to excessive vibrations encountered while passing through the critical speeds. With recommend backup bearings to limit the vibration amplitudes of the rotor it is predicted that the flywheel rotor will show stable operations in the design speed range.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.6
• /
• pp.820-827
• /
• 2014

Since a microgrid has renewable energy sources, imbalance between power supply and power demand occurs in the islanded mode. In order to solve the imbalance, several energy storage systems (ESSs) such as bettary energy storage system (BESS), EDLC (electric double layer capacitor), flywheel, and SMES (superconducting magnetic energy storage) are generally used. Especially, their electrical characteristics are different. For efficient use of them, a coordinated control scheme is required. In this paper, a coordinated control scheme for using a Lead-acid BESS, a Lithium BESS, and a EDLC is designed to efficient frequency control for a microgrid in the islanded mode. The coordinated frequency control strategy is designed based on their electrical characteristics. The feasibility of the proposed coordinated frequency control strategy is verified through the simulation.