• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.230-232
• /
• 2006

Eutectic Au-20Sn solder has been widely used for optoelectronic packages because of fluxless soldering process and thus are particularly valuable for many applications such as biomedical, photonic, and MEMS devices that can not use any flux. Also when good joint strength, superior resistance to corrosion, whisker-free, and good thermal conductivity are demanded, eutectic Au-20Sn solder can be satisfied with above-mentions best. In this study, we tried to know the interfacial reactions between Au-20Sn solder and Cu substrate with or without ENIG plating layer In the results, Au-Cu-Sn ternary phases were formed at the Au-20Sn/Cu substrate, and Au-Ni-Sn, Au-Ni-Cu-Sn phases were formed at the Au-20Sn/ENIG substrate.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.1
• /
• pp.77-85
• /
• 2004

To evaluate the effect of plasma cleaning on the soldering reliability the plasma cleaning using Ar-10vol%$H_2$ gas was applied on a UBM(Under Bump Metallization). The UBM consisted of Au/ Cu/ Ni/ Al layers which were deposited on a Si-wafer with 20 nm/ 4 $\mu\textrm{m}$/ 4 $\mu\textrm{m}$/ 0.4 $\mu\textrm{m}$ thickness respectively. Sn-3.5%Ag, Sn-3.5%Ag-0.7%Cu and Sn-37%Pb solder balls sized of 500 $\mu\textrm{m}$ in diameter were used. Solder balls on the UBM were plasma reflowed under Ar-10%$H_2$ plasma (with or without plasma cleaning). They were compared with air reflowed solder balls with flux. The spreading ratios of plasma reflowed solder with plasma cleaning was 20-40% higher than that of plasma reflowed solder without plasma cleaning. The shear strength of plasma reflowed solder with plasma cleaning was about 58-65MPa. It showed 60-80% higher than that of plasma reflowed solder without plasma cleaning and 15-35% higher than that of air reflowed solder. Thus it was believed that plasma cleaning for the UBM using Ar-10vol%$H_2$ gas was considerably effective for the improvement of the strength of solder ball.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.47-53
• /
• 2000

The fluxless wetting properties of TSM-coated glass substrate were evaluated by the wetting balance method. We could estimate the wettability of the TSM with new parameters obtained from the wetting balance test for one side-coated specimen. It was more effective in wetting to use Cu as a wetting layer and Au as a protection layer than to use Au itself as a wetting layer. The SnSb solder showed better wettability than SnAg, SnBi, and SnIn solders. The contact angle of the one side-coated glass substrate to the Pb-free solders could be calculated from the farce balance equation by measuring the static force and the tilt angle.

• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.99-106
• /
• 2011

Joint strength between a solder ball and a pad on a substrate is one of the major factors which have effects on electronic device reliability. The effort to improve solder joint strength via surface cleaning, heat treatment and solder composition change have been in progress. This paper will discuss the method of solder ball joint strength improvement using LF hydrogen radical cleaning treatment and focus on the effects of surface treatment condition on the solder ball shear strength and interfacial reactions. In the joint without radical cleaning, voids were observed at the interface. However, the specimens cleaned by hydrogen-radical didn't have voids at the interface regardless of cleaning time. The shear strength between the solder ball and the pad was increased over 120%(about 800gf) when compared to that without the radical treatment (680gf) under the same reflow condition. Especially, at the specimen treated for 5minutes, ball shear strength was considerably increased over 150%(1150gf). Through the observation of fracture surface and cross-section microstructure, the increase of joint strength resulted from the change of fracture mode, that is, from the solder ball fracture to IMC/Ni(P) interfacial fracture. The other cases like radical treated specimen for 1, 3, 7, 9min. showed IMC/solder interfacial fracture rather than fracture in the solder ball.

• Electrical & Electronic Materials
• /
• v.6 no.6
• /
• pp.505-513
• /
• 1993

본 논문은 전자 부품의 Soldring기에 사용되는 접합제를 Flux를 포함한 Solder paste 대신에 도금막을 이용하기 위한 Sn 도금막 형성 프로세스를 검토한 것이다. 반도체 Device를 Packaging한 외부단자(lead frame)과 HIC상의 후막전극(Ag/Pd)과의 접합 및 PCB상의 Cu land와의 접합시에는 스크린 프린트에 의한 Solder Paste가 일반적으로 사용되고 있다. 본 논문은 Fluxless Soldering의 한수단으로 도금막을 lead상에 형성시켜 접합 재료로서의 형성 프로세스 및 도금막의 특성과 도금형성 Paramete와의 관련성을 실험적으로 검토한 것으로 전류밀도 200 A/m$^{2}$의 조건으로 형성한 Sn 도금막이 접합용으로 최적조건임을 밝혔다.