• Clean Technology
• /
• v.14 no.1
• /
• pp.53-60
• /
• 2008

The condensation heat transfer coefficients and pressure drops of hydrocarbon refrigerants (R-290 and R-600a) and hydrochlorofluorocarbon (HCFC) refrigerants were measured in the two horizontal double pipe heat exchangers with inner diameters of 10.07 mm and 5.80 mm at a mass flux of $35.5{\sim}210.4\;kg/m^2s$ and the condensation temperature of $40^{\circ}C$. The average condensation heat transfer coefficients of hydrocarbon refrigerants were higher than that of HCFC refrigerant(R-22). The pressure drop had a magnitude in the order of R-600a > R-290 > R-22. The pressure drops in the tubes with inner diameter of 10.07 mm were approximately $6{\sim}15%$, $9.8{\sim}12.5%$ and $2.1{\sim}4.6%$ higher for R-600a, R-290 and R-22, respectively, than those with inner diameter of 5.80 mm. The condensation heat transfer coefficients were compared with the published experimental data, and showed the best agreement with Haraguchi et al.'s correlation.

• Journal of The Korean Astronomical Society
• /
• v.36 no.3
• /
• pp.81-87
• /
• 2003

It is suggested that a flying-by star in a hot accretion disk may cool the hot accretion disk by the Comptonization of the stellar emission. Such a stellar cooling can be observed in the radio frequency regime since synchrotron luminosity depends strongly on the electron temperature of the accretion flow. If a bright star orbiting around the supermassive black hole cools the hot disk, one should expect a quasi-periodic modulation in radio, or even possible an anti-correlation of luminosities in radio and X-rays. Recently, the unprecedentedly accurate infrared imaging of the Sagittarius A$\ast$ for about ten years enables us to resolve stars around it and thus determine orbital parameters of the currently closest star S2. We explore the possibility of using such kind of observation to distinguish two quite different physical models for the central engine of the Sagittarius A$\ast$, that is, a hot accretion disk model and a jet model. We have attempted to estimate the observables using the observed parameters of the star S2. The relative difference in the electron temperature is a few parts of a thousand at the epoch when the star S2 is near at the pericenter. The relative radio luminosity difference with and without the stellar cooling is also small of order $10^{-4}$, particularly even when the star S2 is near at the pericenter. On the basis of our findings we tentatively conclude that even the currently closest pass of the star S2 is insufficiently close enough to meaningfully constrain the nature of the Sagittarius A$\ast$ and distinguish two competing models. This implies that even though Bower et al. (2002)have found no periodic radio flux variations in their data set from 1981 to 1998, which is naturally expected from the presence of a hot disk, a hot disk model cannot be conclusively ruled out. This is simply because the energy bands they have studied are too high to observe the effect of the star S2 even if it indeed interacts with the hot disk. In other words, even if there is a hot accretion disk the star like S2 has imprints in the frequency range at v $\le$ 100 MHz.

• Journal of Korean Society of Forest Science
• /
• v.103 no.1
• /
• pp.80-86
• /
• 2014

$^{210}Pb$ dating was conducted to examine the influence of land use changes in the forest catchment on lake sedimentation. The Kushiro River, into which Lake Takkobu drains under regular flow conditions, contributed to an increased sedimentation rate in sampling point at the lake outflow because turbid water from the Kushiro River flows back into Lake Takkobu during floods. The elevated sediment flux from the catchment dilutes the $^{210}Pb$ concentration in sampling points at the inflow of the Takkobu River and the lake outflow, which causes fluctuations in the $^{210}Pb$ concentrations in sediment cores. The $^{210}Pb$ dating was estimated using the CRS (Constant rate of Supply) model. The dates by the CRS model in Lake Takkobu profiles were in good agreement with the dates by $^{137}Cs$. Sedimentation rates reconstructed for the past 100-150 years suggested that sedimentation rates increased drastically following land use changes. While a natural sedimentation rate of $0.01-0.03g/cm^2/year$ is observed until the 1880s, whereas lake sedimentation accelerated to $0.03-0.09g/cm^2/year$ following land use changes such as deforestation and channelization, between the 1880s and 1940s. In particular, the sedimentation rates have been associated with deforestation, channelization, agricultural development and road construction, since the 1980s, and these rates were about 9-28 times higher than those under natural conditions, leading to accelerated lake shallowing.

• (The)Study of the Eastern Classic
• /
• no.34
• /
• pp.339-362
• /
• 2009

If we try to define the concept of beauty in the large sense, as Kant and Chaung-tzu all agree, It can not be fixed in the one sense, but whose connotation and denotation should be extended infinitely. In this sense, I would like to say that the beauty is liberty. Aesthetics of Kant is oriented toward subjective and reflexive dimension, while that of Chuang-tzu is oriented toward natural and practical one. The difference between aesthetics of the two philosophers begins from their philosophical methodology. If the transcendental methode which is proper to Kant's philosophy prefers to discriminate and devide everything especially from dichotomic viewpoint by langage. But Chuang-tzu' methode called Za-Mang criticizes such a dichotomic division and langage itself. Even so, the two in the long run agree as to the foundation of beauty. But Kant's liberty is one of will or transcendental, meanwhile that of Chuang-tzu is based on recognize the fact that we are all production of nature. according to Chuang-tzu, in the great beginning, there was non-being. It had neither being nor name. The One originates from it. When things obtain it and come into existence. As the One, Tao is in the excrement and urine. Everything is under the constant flux. All species have originative or moving power. Although the universe is vast, its transformation is uniform. Because all things are one. Vacuity, tranquillity, mellowness, quietness, and taking no action characterize the things of universe at peace and represent the ultimate of Tao and virtue. The material was transformed to be form, form was transformed to become life, and now life has transformed to become death. A basic principle of Chuang-tzu's art is expressed in the phrase "taking off clothes and squatting down bare-backed". The key of Chuang-tzu's aesthetics is to dedicate to the expression of inner spirit instead of physical verisimilitude, and painting should be a spontaneous and instantaneous flow of the brush. Kant's concepts such as "disinterested" and "purposiveness of nature" seem to imply in the long run the unification of nature and human being which is fundament to Chuang-tzu's aesthetics.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.33 no.6
• /
• pp.308-320
• /
• 2021

An integrated sediment management approach that includes the recovery of the amount of declined sediment supply is effective as a fundamental solution to coastal erosion. During planning, it is essential to analyze the transfer mechanism of the sediments generated from estuaries (the junction between a river and sea) to assess the amount and rate of sediment discharge (from the river to sea) supplied back to the coast. Although numerical models that interpret the tidal sand bar flushing process during flooding have been studied, thus far, there has been no study focusing on the formation and development processes of tidal sand bars. Therefore, this study aims to construct wave deformation, flow regime calculation, and topographic change analysis models to assess the amount of recovered sediment discharge and reproduce the tidal sand bar formation process through numerical analysis for integrated littoral drift management. The tidal sand bar formation process was simulated, and the wave energy and duration of action concepts were implemented to predict the long-term littoral movement. The river flux and wave conditions during winter when tidal sand bars dominantly develop were considered as the external force conditions required for calculation. The initial condition of the topographic data directly after the Maeupcheon tidal sand bar flushing during flooding was set as the initial topography. Consequently, the tidal sand bar formation and development due to nearshore currents dependent on the incident wave direction were reproduced. Approximately 66 h after the initial topography, a sand bar formation was observed at the Maengbang estuary.

• Korean Journal of Environmental Agriculture
• /
• v.40 no.4
• /
• pp.366-372
• /
• 2021

BACKGROUND: Ammonia is known as a precursor to fine particulate matter, and according to CAPSS, annual ammonia emissions in the agricultural sector were 249,777 tons as of 2018, accounting for about 79.0% of Korea's total ammonia emissions. In particular, ammonia emissions from agricultural land increased by 19,566 tons (10.2%) compared to the previous year. The Ministry of Environment is setting emission statistics using the ammonia emission coefficient developed in Korea in 2008, but researchers in the agricultural field regard it as a coefficient that does not reflect the reality of Korea's agricultural environment. Accordingly, in order to develop ammonia emission coefficients from the cultivation of apples and pears, Korea's representative fruit type, test agricultural land was set in Iksan, Jeollabuk-do. METHODS AND RESULTS: This study attempted to obtain the ammonia emission coefficient by the treatment of the composite fertilizer (N-P₂O₅-K₂O=12-7-9), and the flux was measured using a dynamic flow-through chamber method. As for the chamber, a total of 12 chambers were installed repeatedly in 4 zones and used to develop emission coefficients. Using compound fertilizers during fruit tree cultivation, the ammonia emission coefficient was evaluated as 10.4 kg NH3/ton for pears and 15.3 kg NH₃/ton for apples. The reason why the ammonia emission coefficient according to the use of composite fertilizers was calculated higher for apple cultivation is believed to be due to the relatively high pH concentration of apple orchard soil. CONCLUSION(S): This study may provide basic data for upgrading the ammonia emission coefficient when using composite fertilizers in agricultural land. In the future, it might be necessary to upgrade the calculation of emissions through the development of ammonia and fine particulate matter emission coefficients considering the agricultural environment of Korea.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.3B
• /
• pp.315-321
• /
• 2008

Recently, in the light of environments and utilization, countermeasures to preserve beaches in coastal area are required without depending on such as jetties and breakwaters. The necessity of integrated sand management including not only coastal sediment but also sediment discharge from hinterland rivers is increased so as to establish long-term counterplan for sediment transport. In this regard, the following subjects are examined in this study; efficient ways for discharged sand to be transported from a river to the neighboring coast, the river terrace occurrence and its growth at the river delta, measures to improve storage efficiency of the discharged sand and measures to prevent the sand resources from being discharged into the deep sea during flooding. In recent, A jetty of 260 m length was constructed at Namdae River mouth in the year of 2005 as a countermeasure against the occurrence of sand-bar at river mouth and its close. In this study, a series of numerical experiments were carried out to investigate the characteristics of sediment transport and morphological change due to the construction of jetty at the entrance of Namdae River mouth. Firstly, The sand discharge from Namdae River is quantified by one-dimensional numerical analysis assuming the mixed sand of three different particle diameters. Then, in order to understand the transport behavior of the sand discharge from river and river mouth phenomena the numerical experiments were then conducted to examine the flow behaviors of river efflux and wind generated circulations in coastal area. And, after establishing the numerical model system, which predicts the sea bed changes obtained from the flux model combining with the wave propagation, wave-induced currents and sediment transport models, the sediment transport in the vicinity of Namdae River mouth is analyzed.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.15 no.1
• /
• pp.41-50
• /
• 2010

We have developed an in-situ benthic chamber (BelcI) for use in coastal studies that can be deployed from a small boat. It is expected that BelcI will be useful in studying the benthic boundary layer because of its flexibility. BelcI is divided into three main areas: 1) frame and body chamber, 2) water sampler, and 3) stirring devices, electric controller, and data acquisition technology. To maximize in-situ use, the frame is constructed from two layers that consist of square cells. All electronic parts (motor controller, pA meter, data acquisition, etc.) are low-power consumers so that the external power supply can be safely removed from the system. The hydrodynamics of BelcI, measured by PIV (particle image velocimetry), show a typical "radial-flow impeller" pattern. Mixing time of water in the chamber is about 30 s, and shear velocity ($u^*$) near the bottom layer was calculated at $0.32\;cm\;s^{-1}$. Measurements of diffusivity boundary layer thickness showed a range of $180-230\;{\mu}m$. Sediment oxygen consumption rate, measured in-situ，was $84\;mmol\;O_2\;m^{-2}\;d_{-1}$, more than two times higher than on-board incubation results. Benthic fluxes assessed from in-situ incubation were estimated as follows: nitrate + nitrite = $0.18\;{\pm}\;0.07\;mmol\;m^{-2}\;d^{-1}$ ammonium $23\;{\pm}\;1\;mmol\;m^{-2}\;d^{-1}$ phosphate = $0.09\;{\pm}\;0.02\;mmol\;m^{-2}\;d^{-1}$ and silicate = $23\;{\pm}\;1\;mmol\;m^{-2}\;d^{-1}$.

• Korean Journal of Environmental Agriculture
• /
• v.36 no.3
• /
• pp.193-200
• /
• 2017

BACKGROUND: Plant growth under smart greenhouse (that is plant factory system) conditions of an artificial light type is significantly depending on the artificial light sources such as a fluorescent lamps or Light-Emitting Diodes (LEDs) with specific spectral wavelengths regardless of the outside environmental changes. In this experiment, characteristics on the growth and compound synthesis of kale seedlings affected by light qualities and intensities provided by LEDs were mentioned. METHODS AND RESULTS: The kale seedlings which developed 3~4 true leaves were exposed by fluorescent lamps or LEDs lights of red (R), blue+white (BW), blue+red (BR) with 50 (L) or $100(H){\mu}mol/m^2/s^1$ photosynthetic photon flux (PPF) under hydroponic culture system of deep flow technique for 50 days. Shoot fresh weight increased under the RH, BWH, and BRH treatments with higher PPF. Shoot elongation of the seedlings decreased, and polyphenol synthesis promoted by the higher light intensity conditions. Sugar synthesis in the leaves was above 2 times greater under the RH treatment of monochromic red light quality with $100{\mu}mol/m^2/s^1\;PPF$ than $50{\mu}mol/m^2/s^1\;PPF$. CONCLUSION: The results show that the control of light quality and intensity in the smart greenhouse conditions with artificial lights significantly affects the growth and compound synthesis in the fresh kale leaves with higher culture efficiency compared to the conventional soil culture under greenhouse or field conditions. Researches on the optimum light intensities of the LEDs with special spectral wavelengths are necessary for maximum growth and metabolism in the seedlings.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.388-388
• /
• 2016

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated with cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature $T_s$, and substrate dc bias $V_s$ as variables for efficient PEDOT:PSS/crystalline (c-)Si heterojunction solar cells (Fig. 1). The high-speed camera and differential mobility analysis characterizations revealed that average size and flux of PEDOT:PSS mist depend on f, solvent, and $V_s$. The size distribution of mist particles including EG/DI water cosolvent is also shown at three different $V_s$ of 0, 1.5, and 5 kV for a f of 3 MHz (Fig. 2). The size distribution of EG/DI water mist without PEDOT:PSS is also shown at the bottom. A peak maximum shifted from 300-350 to 20-30 nm with a narrow band width of ~150 nm for PEDOT:PSS solution, whose maximum number density increased significantly up to 8000/cc with increasing $V_s$. On the other hand, for EG/water cosolvent mist alone, the peak maximum was observed at a 72.3 nm with a number density of ~700/cc and a band width of ~160 nm and it decreased markedly with increasing $V_s$. These findings were not observed for PEDOT:PSS/EG/DI water mist. In addition, the Mie scattering image of PEDOT:PSS mist under white bias light was not observed at $V_s$ above 5 kV, because the average size of mist became smaller. These results imply that most of solvent is solvated in PEDOT:PSS molecule and/or solvent is vaporized. Thus, higher f and $V_s$ generate preferentially fine mist particle with a narrower band width. Film deposition occurred when $V_s$ was impressed on positive to a c-Si substrate at a Ts of $30-40^{\circ}C$, whereas no deposition of films occurred on negative, implying that negatively charged mist mainly provide the film deposition. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrate by adjusting $T_s$ and $V_s$. The adhesion of CMD PEDOT:PSS to c-Si enhanced by $V_s$ conspicuously compared to that of spin-coated film. The CMD PEDOT:PSS/c-Si solar cell devices on textured c-Si(100) exhibited a ${\eta}$ of 11.0% with the better uniformity of the solar cell parameters. Furthermore, ${\eta}$ increased to 12.5% with a $J_{sc}$ of $35.6mA/cm^2$, a $V_{oc}$ of 0.53 V, and a FF of 0.67 with an antireflection (AR) coating layer of 20-nm-thick CMD molybdenum oxide $MoO_x$ (n= 2.1) using negatively charged mist of 0.1 wt% 12 Molybdo (VI) phosphoric acid n-Hydrate) $H_3(PMo_{12}O_40){\cdot}nH_2O$ in methanol. CMD. These findings suggest that the CMD with negatively charged mist has a great potential for the uniform deposition of organic and inorganic on textured c-Si substrate by adjusting $T_s$ and $V_s$.