• 한국해양공학회지
• /
• 제10권3호
• /
• pp.117-124
• /
• 1996

A fluidized bed combustion chamber is widely used to incinerate waste material. The most important factor designing the incinerator is the flow characteristics in a fluidized bed, because combustion efficiency is influenced by the flow characteristics. This paper has invesitigated the flow characteristics of bubbles in fluidized bed by means of meassuring a pressure fluctuation in the fluidized bed. A pressure probe system has used to measure the pressure. The data concerned with bubble rising velocity, bubble size, distribution of bubbles and frequency of bubble generation or decay are obtained to find the flow characteristics of bubbles in the fluidized bed. The result obtained from this experimental study can be used to design the fuel feeding system of fluidized bed combustion type incinerator. And it is possible to predict the mixing of waste material and fluidizing material.

• Journal of Biosystems Engineering
• /
• 제31권5호
• /
• pp.416-422
• /
• 2006

Drying characteristics of green onion and onion during fluidized and fixed bed drying were investigated and compared. Sliced peen onion and onion were dried at drying air temperature of 45, 55, and $65^{\circ}C$. Drying air velocity during fluidized bed drying was adjusted with drying time at each drying temperature. Drying time to reach a given final moisture content was shorten in fluidized bed drying than in fixed bed drying - for drying temperature of 45, 55, and $65^{\circ}C$, the differences were 60, 60, and 50 min for green onion and 360, 180, and 60 min for onion. Drying constant (K) was greatly affected by drying method and drying temperature. Terminal velocity under fluidized bed drying was decreased exponentially for green onion and linearly (or onion with increase of drying temperature. Also, terminal velocity had linear relationship with moisture content for both green onion and onion.

• 한국안전학회지
• /
• 제14권3호
• /
• pp.101-109
• /
• 1999

This study attempts to analyse the solid mixing in the feeder and the packing effect for pressure fluctuations in the fluidized bed. To study the mixing characteristics of solid in vibrating feeder for the stable operations of fluidized combustion, the system consisted of two groups of particles such that fine particles were located on the top of the coarse particles before vibratory mixing had started. The effects of packing materials on the pressure fluctuations in a fluidized bed were analysed by using a statistical method to interpret the behavior of fluidized bed. The experiments were carried out in a fluidized bed of 6.7cm-ID, and the experimental variables were particle sizes, of 115 to 1,015$\mu\textrm{m}$ in diameter and the multi-sized particles haying Rosin-Rammler and Gaussian distributions. The settled bed heights of particles to diameter ratios (L/D) were ranged from 0.5 to 2.0. And fluidizing of particles was carried out by air. The packing materials used were screen packing, and the properties of the pressure fluctuations in the fluidized bed were measured by a differential pressure transducer. The properties of the pressure fluctuations calculated were the mean, the standard deviation, and the major frequency of the power spectral density functions. From the characteristics of fluidizing, it was found that the standard deviation of pressure fluctuations could be effectively used to explain the fluidized phenomena, and the packing materials affected severely the properties of the pressure fluctuations. As a result, from the interpretation by spectral analysis, the effects of measuring radius of pressure fluctuations on standard deviation were constant in the case of the fluidized bed with and without packing materials. However, the effects of measuring the height of pressure fluctuations on standard deviations were linear increasing for the fluidized bed with packing materials, but were constant for the fluidized bed without packing materials at 4.5cm above the gas distributor. The major frequency of pressure fluctuations was found to be nearly independent of fluidized system. Also, the major frequency of pressure fluctuations decreased with increasing packing size, and it had maximum value at 10% of the packing amount.

• 설비공학논문집
• /
• 제7권3호
• /
• pp.450-460
• /
• 1995

A modified circulating fluidized bed heat exchanger under severe fouling condition is developed. The effects of fouling deposits on the performance of a heat exchanger are investigated. The principle and operating characteristics of a circulating fluidized bed heat exchanger are dicussed. A modified circulating fluidized bed heat exchanger shows more stable operating than the other circulating fluidized bed heat exchanger. The characteristics of self cleaning and heat transfer enhancement of a circulating fluidized bed heat exchanger are studied. The movement of spherical particles in a tube is visualized and heat transfer enhancement and scale reduction mechanism by particles are investigated.

• 대한기계학회논문집
• /
• 제19권9호
• /
• pp.2365-2372
• /
• 1995

The objective of this study is to get the basic data for the development of fluidized bed combustor. For this purpose, various rake angles(.theta.=20.deg., 25.deg., 30.deg., 35.deg.) of finned tubes and a smooth tube were installed horizontally in the fluidized bed combustor of 410*250mm. The effect of fluidized bed temperature, superficial velocity in bed, size of bed materials, rake angle of finned tubes on the heat transfer coefficient was experimentally investigated. The following results were obtained. (1) Under the fluidized bed temperature(750.deg. C-900.deg. C), and the gas velocity in bed(1.1-2.8m/sec), The highest heat transfer coefficient was measured with the rake angle of finned tubes was .theta.=25.deg. and .theta.=35.deg. for the average fluidized material particle size of 1.22mm and 1.54mm, respectively. Generally, the heat transfer coefficient of finned tubes is 1.4 to 2.4 times larger than that of smooth tubes. (2) The size of bed materials influences the rake angle of finned tubes which can have the highest heat transfer coefficient. As the temperature in bed gets higher, the effect of the rake angle of finned tubes on the heat transfer coefficient becomes greater.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권5호
• /
• pp.24-28
• /
• 1994

In the present paper, the behavior of bubbles in a fluidized bed has been investigated experimentally. The bubble size, distribution of bubble, bubble rising velocity and pressure fluctuation in the fluidized bed are obtained at different air velocity. The results are discussed and compared study the effect of air velocity on the behavior of a bubbles in fluidized bed.

• 설비공학논문집
• /
• 제2권2호
• /
• pp.127-136
• /
• 1990

Air-solid bed has been known to be an effective heat transfer augmentation device which could be applied to heat exchangers. In this study, pressure drop and heat transfer characteristics of vertical annular fluidized bed heat exchanger with air flowing through were studied experimentally. The experiments was conducted to calculate overall heat transfer coefficient on fluidized bed heat exchangers immersed single vertical tube and investigate minimum fluidized velocity in fluidized bed of alumina beads and steel balls. The influence of flow direction, particle diameter, the heights of static bed and air mass fluidizing velocity has been examined. The experimental results showed the optimum operating condition and effective static bed height for fluidized bed heat exchangers. For the same power loss, comparisions of heat transfer effect between the fluidized bed heat exchanger and the single phase forced convetion heat exchanger indicate that both miniaturization of heat exchanger and heat transfer augmentation at low flow velocity are possible by application of the air-solid to heat exchangers.

• 에너지공학
• /
• 제21권1호
• /
• pp.43-46
• /
• 2012

A fluidized bed drying approach was utilized to the synthesis of water glass based silica aerogel powders. The effects of the fluidized bed drying conditions such as the superficial velocity and temperature of hot air and bead size as well as bead/wet-gel ratio, on the physical properties such as tapping density and productivity of the aerogel powders were systematically investigated. The experimental results showed that the amount of beads mixed with wet-gels in the fluidized bed column has the most profound impact on the fluidization efficiency, greatly enhancing the yield of the aerogel powders up to 98% with a proper bead/wet-gel weight ratio as compared to 72% without using beads. No significant change was observed in the tapping density over a wide range of the fluidized drying condition. Consequently the fluidized bed drying approach shows a good promise as an alternative route for the large-scale production of the aerogel powders.

• Journal of Biosystems Engineering
• /
• 제31권4호
• /
• pp.376-384
• /
• 2006

This study was conducted to perform for comparative analysis of the cleaning efficiency on 3 kinds of cleaning liquid state, 3 steps of cleaning temperature $(45^{\circ}C,\;60^{\circ}C,\;70^{\circ}C,\;)$ and 6 steps of cleaning time (2.5, 5, 7.5, 10, 12.5, 15 minute). 3 kinds of cleaning liquid state are the non fluidized bed, liquid fluidized bed and liquid/solid fluidized bed. UV spectrophotometer was used in estimation of cleaning efficiency, which it is experimental equipment using the absorptiometric analysis method. Cleaning efficiency by cleaning time was increase from 2.5 minutes to 15 minutes, liquid/siolid fluidized bed was indicated the highest cleaning efficiency among the 3 kinds of cleaning liquid state and $70^{\circ}C$ of cleaning temperature at liquid/solid fluidized bed was indicated the highest cleaning efficiency as 98% among the 3 steps of cleaning temperature.

• KEPCO Journal on Electric Power and Energy
• /
• 제2권2호
• /
• pp.211-221
• /
• 2016

전세계의 인구 증가와 경제 발전은 지속적인 에너지 수요의 증가를 가져오고 있다. 특히, 전력부분에서는 아시아 및 아프리카, 그리고 중남미 등의 개발도상국을 중심으로 그 수요가 지속적으로 증가하고 있어 주요 에너지원인 석탄의 이용도 지속적으로 증가할 것으로 예측되고 있다. 그러나, 이산화탄소 및 대기오염원, 그리고 미세먼지 등의 배출 등은 석탄을 이용한 전력생산에 있어 환경친화적인 기술로의 대응방안 마련과 더불어, 고효율의 다양한 저급연료를 활용할 수 있는 발전 기술의 개발이 요구되고 있다. 이에, 기술개발 및 그 상용화 시장이 점차 증대되고 있는 초초임계 순환유동층 보일러에 대한 관심이 증대하고 있다. 초초임계 순환 유동층 보일러는 중소형의 아임계의 드럼형 구조에서 벗어나 대용량화의 기본 구조인 Once Through 형태의 증기 순환 구조를 지니고 100-300 MWe의 상업용 모듈의 복제를 통해 600 MW급이 상용화 운전 중에 있으며, 향후 설계가 완성된 800 MWe의 상업화 진행이 기대되고 있다. 초초임계 순환유동층 보일러는 2017년 이후 아임계 순환유동층 보일러 설치 용량을 추월하여 표준형 모델이 될 것으로 전망되고 있어, 본 논문에서의 이의 기술적 배경과 개발 현황 그리고 시장전망 등을 통해 기술적 이해를 도모하고자 한다.