• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1068-1072
• /
• 1997

This work deals with on investigation the influence of various additives to a base stock cutting fluid in order to develop a better deep hold drilling. This investigation has been aiming at developing an oil which gives a maximum cutting efficiency at a minimum wear rate of the tool and the guiding pads. The purpose of study is to analyze how guide pad of tools, workpiece and the change of contained quantity of extreme pressure additive in cutting fluids have effects on the hold over size of cutting hole, surface roughness of workpiece,wear rates of guide pad and roundness during the deep hole machining of SM55C with solid BTA drill by using BTA drilling system through experiment. Conclusion reached is as follows. It has been proved that the contained quantity of surphur more affects machinability than that of extreme pressure additive of chlorine of cutting fluid in BTA drilling during Deep Hole Drilling. Considering its base oil, the the contained quantity of extreme pressure assitive of surphur can be different, but it's judged that the range of 1.5 ~ 2.0% is suitable to machinability for workpiece in BTA drilling. Regarding guide pad, it's judged that the reduction of wear is possible in propotion to the contained quantity of exrreme pressure additive of chlorine against supporting of cutting force and Bumishing operation of machining parts in cutting.

• 한국유체기계학회 논문집
• /
• 제6권3호
• /
• pp.44-50
• /
• 2003

An experiment is conducted for measuring the performance of an air tool, which is operated at 100,000 RPM in an unloaded state with very low torque. A 551 kPa in gauge pressure is supply to the inlet of an air tool. An experimental apparatus is developed as a friction type dynamometer. Inlet total pressure, air flow rate, rotational speed and operating force are measured simultaneously. Torque, output power and specific output power are obtained with different rotational speeds. Those are compared with the experimental results which were obtained by a commercial dynamometer. However, no commercial dynamometers are available for measuring the torque above 30,000 RPM. In order to reduce the rotational speed, a reduction gear is applied between the air tool and the commercial dynamometer. Torque and power obtained by the commercial dynamometer show $55\%$ lower than those obtained by the developed friction type dynamometer, because the mass is added to the rotor of air tool for the braking system of the commercial dynamometer and power loss is generated by the reduction gear. From the compared results, the friction type dynamometer should be applied for measuring the performance of the air tool operating at low torque and high RPM.

• Ocean Systems Engineering
• /
• 제7권3호
• /
• pp.225-246
• /
• 2017

Excessive dynamic-tension variations on the top-tensioned risers (TTRs) deteriorate the structural integrity and cause potential safety hazards. This phenomenon has become more remarkable in the development of deep-water fields with harsher environmental loads. The conventional prediction method of tension variations in hydro-pneumatic tensioner (HPT) has the disadvantage to underestimate the magnitude of cyclic loads. The actual excessive dynamic tension variations are larger when considering the viscous frictional fluid effects. In this paper, a suppression method of tension variations in HPT is modeled by incorporating the magneto-rheological (MR) damper and linear-force actuator. The mathematical models of the combined HPT and MR damper are developed and a force-control scheme is introduced to compensate the excessive tension variations on the riser tensioner ring. Numerical simulations and analyses are conducted to evaluate the suppression of tension variations in HPT under both regular- and irregular-wave conditions for a drilling riser of a tensioned-leg platform (TLP). The results show that significant reduction of tension variations can be achieved by introducing the proposed system. This research has provided a theoretical foundation for the HPT tension control and related structural protection.

• 한국소음진동공학회논문집
• /
• 제17권2호
• /
• pp.168-176
• /
• 2007

The mixture sound speed in bubbly fluids is highly dispersive due to differences of the density and compressibility between bubbles and fluids. The dispersion range in bubbly fluids expands to a higher frequency than the resonance frequency of an air bubble. A theoretical model was developed to compute the reduction of radiation noise that is generated by a force applied on an infinite flat plate using a bubble layer as a compliant baffle. For evaluating the effectiveness of a bubble layer in reducing the structure-borne noise of an infinite elastic plate, the noise reduction levels for various parameters such as the thickness of bubble layers, the volume fractions and the distribution types of bubbly fluids are calculated numerically. The noise reduction effect of an air bubble layer on an infinite flat plate is considerable level and similar to the tendency of dispersion of bubbly fluids. It is recommended that the thickness of a bubble layer should be increased with keeping an appropriate volume fraction of an air bubble for the most effective reduction of the radiation noise.

• Tribology and Lubricants
• /
• 제26권1호
• /
• pp.1-6
• /
• 2010

In the last decade, laser surface texturing (LST) has emerged as a viable option of surface engineering. Many problems related with mechanical components such as thrust bearings, mechanical face seals and piston rings, etc, LST result in significant improvement in load capacity, wear resistance and reduction in friction force. It is mainly experimentally reported the micro-dimpled bearing surfaces can reduce friction force, however, precise theoretical results are not presented until now. In this paper, a commercial computational fluid dynamics(CFD) code, FLUENT is used to investigate the lubrication characteristics of a parallel thrust bearing having 3-dimensional micro-dimple. The results show that the pressure, velocity and density distributions are highly affected by the location and number of dimple. The numerical method and results can be use in design of optimum dimple characteristics, and further researches are required.

• Agricultural and Biosystems Engineering
• /
• 제7권1호
• /
• pp.13-17
• /
• 2006

The planocentric gear, known as wobble mechanism, has been used for speed reducing mechanism as an ingenious mechanism. The modem application can be found in the backrest adjusting mechanism of a vehicle reclinable seat, fluid pumps and aircraft hoist and winches. Higher speed reduction ratios, high load capacity, lower weight, and compactness are the main advantages of this gear. This paper presents velocity and static force analysis to investigate the friction lock of the planocentric gear. The rectilinear tooth profile is used to maximize the speed reduction ratio. The equivalent linkage system is used for the analysis of instantaneous motion. As the results, the transmission efficiency of the planocentric gear is found and the friction lock of the system is determined for the friction coefficients of journals. A numerical example that illustrates the developed analysis is presented.

• 대한기계학회논문집B
• /
• 제41권7호
• /
• pp.435-443
• /
• 2017

본 연구는 고 레이놀즈 영역에서 상류측에 작은 정방형주(Square prism)를 가진 정방형주의 유동장 특성을 양 항력측정 실험과 PIV를 이용한 가시화 실험으로 파악한 것이다. 실험변수는 정방형주 한변의 길이에 대한 작은 정방형주의 폭비(H/B=0.2~0.6) 및 정방형주 전면에서부터 작은 정방형주의 후면 까지의 거리(G/B=0~3)로 했다. 작은 정방형주의 폭비를 고정시킨 경우 정방형주의 항력감소율은 간격비가 증가할수록 증가하다 감소하는 특성을 보였다. 또한 같은 간격비에서는 작은 정방형주의 폭비가 클수록 정방형주의 항력감소율이 컸다. 또한 같은 간격비에서는 작은 정방형주의 폭비가 클수록 정방형주의 항력감소율이 증가했으며, 폭비 H/B=0.6, 간격비 G/B=1.0일 때 최대 98.0%의 항력감소율을 보였다. 정방형주의 양력감소율은 작은 정방형주의 폭비 및 간격비에 거의 영향을 받지 않았으며, 양력감소율의 전체 평균치는 66.5% 정도였다. 작은 정방형주를 설치한 경우 정방형주 상류측과 하류측에 정체영역이 나타났다.

• 한국기계가공학회지
• /
• 제16권2호
• /
• pp.63-68
• /
• 2017

Friction occurs when surfaces that are in contact move relatively between solid surfaces, fluid layers, and materials slide against one another. This friction force causes wear on the contact surface, generates unwanted heat and leads to performance degradation. Thus, much research has been performed to avoid friction reduction. Among these studies, a textured surface that has micro patterns on the surface has drawn attention for its ability to reduce friction. A mathematical model is developed in this study to examine friction reduction due to the texture of a surface. Numerical simulations are carried out with respect to various factors such as the shape aspect ratio and texture depth of a diamond-shaped texture in the hydrodynamic lubrication regime. As a result, a shape aspect ratio of 1 is best for friction reduction.

• 한국소음진동공학회논문집
• /
• 제19권11호
• /
• pp.1222-1230
• /
• 2009

A theoretical model was developed to compute the effect of a bubble layer in reducing the radiation noise generated by a force applied on an infinite flat plate considering the noise of multi-bubbles. Using the model, the effectiveness of a bubble layer in reducing the structure-borne noise of the plate was evaluated to consider various parameters such as the source noise levels, the thickness of bubble layers, the volume fractions and the frequency characteristics of bubbly fluids. Considering the noise of multi-bubbles, the actual reduction effect of radiation noise using a bubble layer was expected in cases of high source levels, high volume fractions of bubbles and large thickness of the bubble layer above the resonance frequency of the bubble layer. Accordingly, it is recommended that the thickness of a bubble layer, the source noise level and the characteristics of bubbly fluids should be optimized cautiously to maximize noise reduction effects.

• 한국산학기술학회논문지
• /
• 제20권2호
• /
• pp.655-661
• /
• 2019

본 연구는 차량용 리어 디퓨저의 시작 위치에 따른 주행 성능 변화를 분석하고자 하였다. 이를 위해 CATIA 3D 설계 프로그램을 이용하여 상용 SUV 차량을 참고하여 차량을 모델링하고 뒤 타이어를 기준으로 300, 400, 500 mm 떨어진 위치부터 리어 디퓨저가 시작되도록 설계했다. 그리고 유동 해석 프로그램인 Fluent를 이용해 차량 주행속도가 60km/h, 100km/h, 140km/h 일 경우를 조건으로 하여 유동해석 후 양력과 항력의 변화를 분석하고 공기의 유선 변화를 확인했다. 해석 결과, 리어 디퓨저는 시작 위치에 상관없이 디퓨저가 없는 경우에 비해 양력과 항력을 감소시켰다. 이는 리어 디퓨저가 있을 경우 공기가 차량 하면부를 지나 후면부로 빠져나올 때 발생하는 박리 현상을 억제하여 와류 현상을 감소시키기 때문이다. 또한 본 연구에서는 SP 400의 조건일 때 양력이 가장 작았고 양력 감소 효과도 가장 좋았기 때문에 주행 중 타이어의 접지력을 최대로 확보할 수 있어서 이 경우를 최적의 조건으로 결정하였다.