• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.3
• /
• pp.529-561
• /
• 2014

The two-phase turbulent flow past an interface-piercing circular cylinder is studied using a high-fidelity orthogonal curvilinear grid solver with a Lagrangian dynamic subgrid-scale model for large-eddy simulation and a coupled level set and volume of fluid method for air-water interface tracking. The simulations cover the sub-critical and critical and post critical regimes of the Reynolds and sub and super-critical Froude numbers in order to investigate the effect of both dimensionless parameters on the flow. Significant changes in flow features near the air-water interface were observed as the Reynolds number was increased from the sub-critical to the critical regime. The interface makes the separation point near the interface much delayed for all Reynolds numbers. The separation region at intermediate depths is remarkably reduced for the critical Reynolds number regime. The deep flow resembles the single-phase turbulent flow past a circular cylinder, but includes the effect of the free-surface and the limited span length for sub-critical Reynolds numbers. At different Froude numbers, the air-water interface exhibits significantly changed structures, including breaking bow waves with splashes and bubbles at high Froude numbers. Instantaneous and mean flow features such as interface structures, vortex shedding, Reynolds stresses, and vorticity transport are also analyzed. The results are compared with reference experimental data available in the literature. The deep flow is also compared with the single-phase turbulent flow past a circular cylinder in the similar ranges of Reynolds numbers. Discussion is provided concerning the limitations of the current simulations and available experimental data along with future research.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.5
• /
• pp.2985-2992
• /
• 2015

In this study, the characteristics of heat transfer and pressure drop was theoretically analyzed by changing longitudinal pitch, bump phase, location of vortex generator about the staggered tube banks by applying SST (Shear Stress Transport) turbulence model of ANSYS FLUENT v.14. Before carrying out CFD (Computational Fluid Dynamics) analysis, It is presumed that the boundary condition is the tube surface temperature of 363 K, the inlet air temperature of 313 K and the inlet air velocity of 5-10 m/s. The results indicated that the heat transfer coefficient is not affected by the longitudinal pitch and the bump phase of circle type was more appropriate than serrated type in the characteristics of heat transfer and pressure drop. Additionally, in case of vortex generator location, the heat transfer characteristics showed that forward location of tube was more favorable 4.6% than backward location.

• Journal of Korea Water Resources Association
• /
• v.31 no.3
• /
• pp.223-234
• /
• 1998

Recently, the interests of the construction of the permeable submerged breakwaters have been increased to preserve and to improve the coastal environment, and to control the incident waves and littoral transport. It is very important to predict the wave transformation precisely over the permeable submerged breakwaters. This study discusses nonlinear wave transformation and characteristics by using BEM based on the frequency domain method of the 3rd-order Stokes waves. The Dupuit-Forchheimer formula is applied to the analysis of the fluid resistance of rubble stones, and the equation about equivalent linear frictional coefficient is newly modified based on the Lorentz's condition for the equivalent work. The numerical results are compared with the experimental ones for verification. These two results give a close agreement each other. It is confirmed that the present method of the 3rd-order Stokes waves estimates more precisely than that of the 2nd-order Stokes waves.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.292-292
• /
• 2017

하천에서 주로 부유사의 형태로 이송되는 유사는 크게 점착성 유사와 비점착성 유사로 구분된다. 입자의 크기가 약 $63{\mu}m$이하인 유사는 입자 표면의 전자기적 점착력의 영향이 우세하여 유사입자들은 지속적인 응집현상을 겪는다. 응집 현상을 통해 유사의 가장 단위인 일차입자(Primary Particle)들은 하나의 커다란 덩어리인 플럭(Floc)을 형성한다. 응집현상이 중요한 이유는 형성된 플럭의 크기 및 밀도가 끊임없이 변화하는 데 있다. 크기와 밀도의 지속적인 변화로 인하여 유사의 부유에 직접적으로 관계하는 침강속도가 변화한다. 우리나라의 금강 및 낙동강의 하구는 점착성 유사가 지배적인 환경으로, 하구에서의 유사 이동을 살펴보기 위해서는 흐름 방향 및 연직방향으로의 흐름 특성(Hydrodynamics)변화와 응집 모형을 통한 응집 현상의 고려가 필수적이다. 이에따라, 본 연구에서는 흐름 방향 및 연직방향으로의 2차원 점착성 유사 이동모형에 관한 개념적 틀(Framework)을 제시한다. 2차원 점착성 유사 이동 모형의 개념적 틀은 기존의 1차원 연직 점착성 유사 이동 모형을 근간으로 한다. 모형에서 흐름을 구성하는 지배 방정식은 오일러-오일러 이상방정식(Eulerian-Eulerian Two-Phase Equation)을 통해 얻는다. 유사상(Sediment Phase, Dispersed Phase)와 유체상(Fluid Phase, Continuous Phase)는 혼합물 이론(Mxiture Theory)를 통해 하나의 혼합물 상(Mixture Phase)의 지배방정식으로 대표된다. 난류의 계산은 와점성 모형 중 -${\varepsilon}$모형을 통해 수행되며, 부유사의 농도는 유사의 이송-확산 방정식을 통해 모의된다. 입력된 흐름 조건을 따라 초기 흐름이 모의되면, 유체 내에서 시간에 따른 플럭의 크기가 계산된다. 플럭의 크기가 계산되는 과정에서 밀도와 침강 속도가 계산되며, 그 이후에 유체 내 유사의 농도가 계산된다. 난류 모의가 수행되고 난 이후에, 유속이 재계산 된다. 이러한 과정을 통해 흐름 방향 및 연직 방향으로의 유사 이동 모의가 가능한 2차원 점착성 유사 이동 모형이 개발될 수 있을 것이라고 생각된다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.1
• /
• pp.1-12
• /
• 1998

Industrial ejector system is a facility to transport, to compress or to pump out a low pressure secondary flow by using a high pressure primary flow. An advantage of the ejector system is in its geometrical simplicity, not having any moving part, compared with other fluid machinery. Most of the previous works have been performed experimentally and analytically. The obtained data. are too insufficient to improve our current understanding on the detailed flow field inside the ejector. In order to provide more comprehensive data on this ejector flow field, two-dimensional computations using Reynolds-averaged Navier-Stokes equations were performed for a very wide range of operating pressure ratio of the supersonic ejector with a secondary throat. The current results showed that the supersonic ejector system has an optimum pressure ratio for the secondary flow total pressure to be minimized. The numerical results clearly revealed the shock system, shock/boundary layer interaction, and secondary flow entrainment inside the supersonic ejector.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.4
• /
• pp.331-340
• /
• 2021

The blast damage behavior of reinforced concrete (RC) structures exposed to unexpected extreme loading was investigated. To enhance the accuracy of numerical simulation for blast loading on RC structures with seven blast points, the calculation of blast loads using the Euler-flux-corrected-transport method, the proposed Euler-Lagrange coupling method for fluid-structure interaction, and the concrete dynamic damage constitutive model including the strain rate-dependent strength and failure models was implemented in the ANSYS-AUTODYN solver. In the analysis results, in the case of 20 kg TNT, only the slab member at three blast points showed moderate and light damage. In the case of 100 kg TNT, the slab and girder members at three blast points showed moderate damage, while the slab member at two blast points showed severe damage.

• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.4
• /
• pp.228-235
• /
• 2021

Polymer electrolyte membrane fuel cells (PEMFC) are currently being used in various transport applications such as drones, unmanned aerial vehicles, and automobiles. The power required is different according to the type of use, purpose, and the conditions adjusted using a cell stack. The fuel cell stack is compressed to reduce the size and prevent fuel leakage. The unit cells that make up the cell stack are subjected to compression by clamping force, which makes geometrical changes in the porous media and it impacts on cell performance. In this study, finite elements method (FEM) and computational fluid dynamics (CFD) analysis for the deformed unit cell considering the effects of clamping force is performed. First, structural analysis using the FEM technique over the deformed gas diffusion layer (GDL) considering compression is carried out, and the resulting porosity changed in the GDL is calculated. The PEMFC model is then verified by a three-dimensional, two-phase fuel cell simulation applying the physical properties and geometry obtained before and after compression. The detailed simulation results showed different concentration distributions of fuel between the original and deformed geometry, resulting in the difference in the distribution of current density is represented at compressed GDL region with low oxygen concentration.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.2
• /
• pp.211-218
• /
• 2021

This paper deals with the computational work to characterize the formation and pinching of a plasma in an X-pinch configuration. A resistive magnetohydrodynamic model of a single fluid and two temperature is adopted assuming a hollow conical structure in the (r,z) domain. The model includes the thermodynamic parameter of tungsten from the corrected Thomas-Fermi EOS(equation of state), determining the average ionization charge, pressure, and internal energy. The transport coefficients, resistivity and thermal conductivity, are obtained by the corrected Lee & More model and a simple radiation loss rate by recombination process is considered in the simulation. The simulation demonstrated the formation of a core-corona plasma and intense compression process near the central region which agrees with the experimental observation in the X-pinch device at Seoul National University. In addition, it confirmed the increase in radiation loss rate with the density and temperature of the core plasma.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.27 no.3
• /
• pp.175-180
• /
• 2021

Although it has recently been regulated for use as an eco-friendly policy in Korea, the use of EPS (Expanded Polystyrene) cooling boxes, which are used as cold chain delivery insulation boxes for fresh agricultural and livestock products, is also increasing rapidly as e-commerce logistics such as delivery have increased rapidly due to COVID-19. Studies were conducted to optimize the EPS cooling container through internal air heat flow of CFD (Computational Fluid Dynamics) analysis and FEM (Finite Element Method) random vibration analysis using domestic PSD (Power Spectral Density) profile of the EPS cooling box to which the refrigerant is applied in this study. In the analysis of the internal air heat flow by the refrigerant in the EPS cooling box, the application of vertical protrusions inside was excellent in volume heat flow and internal air temperature distribution. In addition, as a result of random vibration analysis, the internal vertical protrusion gives the rigid effect of the cooling box, so that displacement and stress generation due to vibration during transport are smaller than that of a general cooling container without protrusion. By utilizing the resonance point (frequency) of the EPS cooling box derived by the Model analysis of ANSYS Software, it can be applied to the insulation and cushion packaging design of the EPS product line, which is widely used as insulation and cushion materials.

• Particle and aerosol research
• /
• v.17 no.4
• /
• pp.81-89
• /
• 2021

Understanding particle-laden flow around cylindrical bodies is essential for the better design of various applications such as filters. In this study, laminar flows around two tandem cylinders and the motions of particles in the flow are numerically investigated at low Reynolds numbers. We aim to reveal the effects of the spacing between cylinders, Reynolds number and particle Stokes number on the characteristics of particle trajectories. When the cylinders are placed close, the unsteady flow inside the inter-cylinder gap at Re = 100 shows a considerable modification. However, the steady recirculation flow in the wake at Re = 10 and 40 shows an insignificant change. The change in the flow structure leads to the variation of particle dispersion pattern, particularly of small Stokes number particles. However, the dispersion of particles with a large Stokes number is hardly affected by the flow structure. As a result, few particles are observed in the cylinder gap regardless of the cylinder spacing and the Reynolds number. The deposition efficiency of the upstream cylinder shows no difference from that of a single cylinder, increasing as the Stokes number increases. However, the deposition on the downstream cylinder is found only at Re = 100 with large spacing. At this time, the deposition efficiency is generally small compared to that of an upstream cylinder, and the deposition location is also changed with no deposited particles near the stagnation point.