• 한국분무공학회지
• /
• 제27권1호
• /
• pp.26-35
• /
• 2022

Electrospray is a method of atomizing fluid using high voltage supply and capable of generating continuous flow and coherent size of droplets. Electrical system and properties of fluids has enabled electrospray to have various spray modes. However, its studies have been confined only in Cone jet, which is more stable and easier to manipulate droplets' size than other spraying modes. Therefore, it is necessary to investigate and compare other spraying modes based on experimental parameters and physical properties of fluids. This research paper identified nine different spray modes. It was found out that Sauter Mean Diameter (SMD) is proportional to flow rate of fluids and maximum difference among spray modes was 1.7 times. On the other hand, SMD standard deviation had low variations on specific flow rates of fluids. Pulsed jet mode recorded the largest SMD standard deviation, while Spindle recorded the lowest.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권5호
• /
• pp.566-575
• /
• 2011

LPG 연료공급방식은 배출가스를 저감시킬 수 있는 유용한 시스템으로 연구가 지속적으로 진행되고 있다. LPG는 경유와 휘발유보다 높은 증기압과 낮은 점도와 표면장력을 유지하므로 고무류와 화학 반응에 따른 연료펌프의 기계적인 손상으로 내구성이 저하되고 있는 실정이다. 본 연구에서는 이러한 문제점을 해결하기 위해 LPLi 시스템에서 유지보수의 편리함과 가격경쟁을 위해 개발된 외장형 펌프를 사용하여 LPG 연료의 조성 및 온도에 따른 특성을 평가하고자 실험을 하였다. 그 결과로서, 내장형 펌프와 외장형 펌프의 성능차이는 거의 없으며 프로판 함유율이 높고, 연료온도가 높아짐에 따라 유량은 많아지나 펌프효율은 거의 차이가 없었다. 또한 LPG 자동차 연료공급장치의 특성상 연료조성 및 온도변화에 따른 차압도 거의 일정하게 나타내었다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2005년도 추계 학술대회논문집
• /
• pp.219-222
• /
• 2005

Recently, the interest of the engine capacity and environment of the atmosphere is increasing, so the researches for the engine capacity have been conducted for a long time. But the internal environment of an automotive engine is very severe. A piston is exposed to combustion gas of over $2000^{\circ}C$ and strong friction is occurred by high speed motion in the cylinder. The fraction between piston and wall of the cylinder causes the increase of temperature in the engine. The temperature of the engine has an effect on the engine capacity. If the temperature is high, the capacity of the engine is low. So we have to maintain the optimum temperature. To maintain the optimum temperature, the enough flow rate of the engine oil is needed. The oil jet is used to control the flow rate of the engine oil and supply the engine oil to the piston and cylinder. The purpose of this study is to check the mass flow rate of the engine oil and the characteristics of internal flow of the oil jet. Flow pattern of the engine oil is very important because it concludes the loss in the oil jet. This study is the previous research about the oil jet and we will consider the movement of the ball check valve to get more accuracy result.

• 동력기계공학회지
• /
• 제19권3호
• /
• pp.69-74
• /
• 2015

Check valves used in vessels include shock-release function on piping system, aside from basic back flow prevention. However, proper and enough protection of system is not obtainable due to use of high-pressure and bulk fluids, resulting from enlargement of vessels. In this study, casting analysis of check valves protecting systems in flow path from water hammering or back flow is conducted, using Z-CAST program. Also, molten metal filling, flow analysis, solidification analysis and shrinkage cavity analysis are conducted. The main results are as following. Regarding filling of each risering, molten metal showed stable supply condition without being isolated. It was identified that the final solidification exists on risering, but shrinkage cavity possibly might happens at the point of isolation solidification.

• 한국기계가공학회지
• /
• 제21권9호
• /
• pp.42-49
• /
• 2022

An underground electric switch is a high-voltage switch used in distribution network systems for a reliable power supply. Many studies are being conducted to expand the switch to use an eco-friendly gas using dry air instead of SF6 gas to reduce greenhouse gas emissions. In this study, a flow analysis model was established to improve the performance of an eco-friendly gas switch. The results were compared and reviewed through experiments. For the optimal arc grid design applied to the switch, the flow characteristics based on the flow path configuration and the changes in arcing time for each configuration were compared. Flow analysis can predict the switch flow distribution, and a comparative review of the flow path configurations of various methods is possible.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.448-453
• /
• 2005

Temperature Control Valve (TCV) is one of the useful temperature control devices, which is used to control constant temperature of working fluid in power and chemical plants and domestic water supply systems. TCV is composed of body, cylinder and piston, and the body shape has a symmetrical H-type. In general, it has several inlet and outlet holes, and its shape is like as tubular sleeve. The piston has three rings two rings of the end of piston have the function of controlling inlet flow rate with hot and cold working fluids, the center ring has the function of preventing hot and cold water from intermixing. Consequently, the shapes of piston and cylinder are the main design parameters in the performance of TCV. In this study, numerical analyses were carried out with two different piston and cylinder shapes to investigate the functions as a temperature control valve and the flow characteristics according to piston opening grade in TCV. Using a commercial code, FLUENT, velocity and pressure fields in TCV are obtained under steady, standard $k -{\epsilon}$ turbulence model and no-slip condition.

• 한국정밀공학회지
• /
• 제25권5호
• /
• pp.112-120
• /
• 2008

This study has been conducted to investigate the characteristics of flow field and discharge valve motion in a rotary compressor. In this study, a transient three-dimensional numerical analysis using FSI(Fluid-Structure Interaction) model has been employed to analyze the interaction between the discharge valve and the refrigerants in the rotary compressor. It has been observed that two peaks have appeared in the displacement of the discharge valve. The maximum displacement of the discharge valve has been found to be located at the second peak. Also, the input pressure of the refrigerants has been compared with the pressures of the muffler passage and the compressor outlet in the rotary compressor. The pressure has decreased along the pathway in the rotary compressor. And the volume flow rates obtained from the current numerical study have been compared with the experiment at data to verify the validity of the present numerical study. This study may supply the fundamental data for the design of rotary compressors.

• 한국기계가공학회지
• /
• 제18권10호
• /
• pp.83-92
• /
• 2019

A pump is considered to be submersible when a motor and a pump are integrated and operate while submerged in water. Submersible pumps mainly function as rejection pumps to prevent foods in densely populated areas, as cold water circulation pumps in large power plants, as pumps to supply irrigation water, as drainage pumps to prevent flooding of agricultural lands, as water supply intake pumps, and as inflow pumps for sewage treatment. The flow in such turbomachines (submersible pumps) inevitably involves various eddy currents. Since it is almost impossible to accurately grasp the complex three-dimensional flow structure and characteristics of a rotating turbomachine through actual testing, three-dimensional numerical analysis using computational fluid dynamics techniques measuring the flow field, velocity, and the pressure can be accurately predicted. In this study, the shape of the impeller was developed to reduce vibration and noise. This was done by increasing the efficiency of the existing submersible pump and reducing turbulence. In order to evaluate the pump's efficiency and turbulence reduction, we tried to analyze the flow using ANSYS Fluent V15.0, a commercial finite element analysis program. The results show that the efficiency of the pump was improved by 4.24% and the Reynolds number was reduced by 15.6%. The performance of a developed pump with reduced turbulence, vibration, and noise was confirmed.

• 한국추진공학회지
• /
• 제2권2호
• /
• pp.24-29
• /
• 1998

Duplex Type의 2-유체 공기충돌형 Swirl 인젝터의 분무특성을 파악하고자 유체공급압력 0~13kg/$\textrm{cm}^2$ 범위에서 유량계수, 등가 분산각, 질량분포를 실험적으로 구하였다. 일반적으로 기체의 총 유량이 증가할수록 미립화는 촉진되나 반경방향 유량이 많은 경우에 분무형상은 비교적 안정적이었으며, 축방향 보다는 반경방향 선회기가 미립화에 미치는 영향이 컸다. 3kg/$\textrm{cm}^2$을 제외하고는 물 유량이 증가함에 따른 등가 분산각의 변화는 미소하였고, 기체의 유량증가도 마찬가지였다. Patternator를 사용한 질량 분포는 반경방향 기체유량이 증가함에 따라 분포곡선의 최대점은 낮아지면서 더 넓은 영역에 걸쳐 분포하였고, 물 유량의 증가에 따른 질량중심점의 위치는 변화가 없었다.

• 해양환경안전학회지
• /
• 제6권1호
• /
• pp.69-76
• /
• 2000

Bubble boom may be a good alternative for the prevention of oil spill pollution due to its easy deployment and clean post-process tasks. The present work is focused on the experimental investigation of air bubble movement for the bubble boom by visualization and quantitative PIV measurements. Bubble plume was generated by adjusting the pressure of pressure vessel ranging 6.7 kpa to 14.7 kpa. The results showed at lower inlet velocity and higher supply air flow rate that bubble boom maintained its containing capability reasonably well up to the maximum containing limit.