• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1998년도 춘계학술대회논문집; 용평리조트 타워콘도, 21-22 May 1998
• /
• pp.75-80
• /
• 1998

Statistical Energy Analysis(SEA) has been considered as a possible method for predicting responses of complex structures, especially at higher frequencies. In this paper, an SEA model of vehicle was built using 138 energy storing subsystems connected together using 1019 junctions. SEAM software program was used to build and calculate the model. To demonstrate the accuracy of the SEA model, predicted response levels were compared with measured levels. The source input levels were measured at the engine mounting parts. For the vibration levels, the agreement between the calculation results and the experimental ones was found to be good. The energy flow between connected subsystems can be presented, because the analysis method is based on the estimation of the power flow between subsystems. This paper also identifies some dominant energy flow paths from sources. It is finally presented that the SEA model can optimize the design parameters of vehicles using model parameters and energy flow paths.

• 소음진동
• /
• 제10권4호
• /
• pp.602-609
• /
• 2000

When an axisymmetric body moves through air the boundary layer near the stagnation region remains laminar and subsequently it goes through transition to turbulent. The experimental investigation described in this paper concerns the characteristics of wall pressure fluctuations at the initial stage of boundary layer flow including transition. Flush-mounted microphones are used to measure the wall pressure fluctuations at the transition and turbulent boundary layer region of a blunt axisymmetric body in the low noise wind tunnel. It if found from this study that the wall pressure fluctuations in the transition region is higher than that in the turbulent region.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2010년도 춘계학술대회 논문집
• /
• pp.340-341
• /
• 2010

A computational study to capture the flow around a floor mounted greenhouse shaped HAWT model was performed using the commercial software PowerFLOW 4.2b. The simulation kernel of this software is based on the numerical scheme known as the Lattice Boltzmann Method (LBM), combined with an RNG turbulence model. Simulations were performed at 60 and 140 km/h free stream air speeds. Selective results from these computational simulations are presented to show the capability of this numerical approach to predict the aerodynamics and aeroacoustics characteristics of the 3-D flow field around the HAWT model.

• Journal of Ship and Ocean Technology
• /
• 제7권3호
• /
• pp.13-33
• /
• 2003

This paper presents a numerical study on tip vortex cavitation inception predictions based on non-spherical bubble dynamics including splitting and jet noise emission. A brief summary of the numerical method and its validation against a laboratory experiment are presented. The behavior of bubble nuclei is studied in a tip vortex flow field at two Reynolds numbers, provided by a viscous flow solver. The bubble behavior is simulated by an axisymmetric potential flow solver with the effect of surrounding viscous flow taken into account using one way coupling. The effects of bubble nucleus size and Reynolds number are studied. An effort to model the bubble splitting at lower cavitation numbers is also described.

• 한국전산유체공학회지
• /
• 제22권1호
• /
• pp.103-109
• /
• 2017

The aerodynamic noise reduction of railway traction motor is required to satisfy new enhanced Korean noise regulations for a train. This paper is the study result on a noise reduction of a railway traction motor using Lattice Boltzmann Method(LBM). To verify the reliability of numerical analysis, the noise performance of the base model evaluated using LBM, and calculated result was compared with the experimental data. In addition, main noise sources were selected to design parameters through analyzing the flow field of the base model. Based on the noise sources analysis result, a design improvement model of traction motor for this study was derived to reduce the noise. The performance of a design improvement model was evaluated by applying a validated numerical scheme. As a result, it was confirmed that the noise was reduced due to the suppression of the internal turbulent flow components.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 추계학술대회 논문집
• /
• pp.291-291
• /
• 2013

The interior vehicle noise due to the exterior aerodynamic field is an important topic in the acoustic design of a car. The air flow detached from the A-pillar and impacting the side windows are of particular interest as they are located close to the driver / passenger and provides a lower insulation index than the trimmed car body parts. HMC is interested in the numerical prediction of this aerodynamic noise generated by the car windows with the final objective of improving the products design and reducing this noise. The methodology proposed in this paper relies on two steps: the first step involves the computation of the exterior flow and turbulence induced non-linear acoustic field using the CAA(Computational aeroacoustics) solver CAA++. The second step consists in the computation of the vibro-acoustic transmission through the side window using the finite element vibro-acoustic solver Actran. The internal air cavity including trim component are included in the simulation. In order to validate the numerical process, an experimental set-up has been created based on a generic car shape. The car body includes the windshield and two side windows. The body is made of aluminum and trimmed with porous layers. First, this paper describes the method including the CAA and the vibro-acoustic models, from the boundary conditions to the different components involved, like the windows, the trims and the car cavity is detailed. In a second step, the experimental set-up is described. In the last part, the vibration of the windshield and windows, the total wind noise level results and the relative contributions of the different windows are then presented and compared to measurements. The influence of the flow yaw angle (different wind orientation) is also assessed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.666-666
• /
• 2007

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.784-787
• /
• 2003

Electrorheological(ER) and magnetorheological(MR) fluid-based dampers are typically analyzed using Bingham-plastic shear model under quasi-steady fully developed flow conditions. A Herschel-Bulkley constitutive shear flow relationship is that the linear shear stress vs. strain rate behavior of Bingham model is replaced by a shear stress that is assumed to be proportional to a power law of shear rate. This power is called the flow behavior index. Depending on the value of the flow behavior index number, varying degrees of post-yield shear thickening or thinning behavior can be analyzed. But it is not practical to analyze the damping force in a flow mode damper using Herschel-Bulkley model because it is needed to solve a polynomial equation. A useful guide is suggested to analyze the damping force in a damper using the Herschel-Bulkley model.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.70.2-70.2
• /
• 2005

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.950-951
• /
• 2012