• International Journal of Railway
• /
• 제7권4호
• /
• pp.100-108
• /
• 2014

A numerical analysis method for predicting aerodynamic noise at inter-coach space of high-speed trains, validated by wind-tunnel experiments for limited speed range, is proposed. The wind-tunnel testing measurements of the train aerodynamic sound pressure level for the new generation Korean high-speed train have suggested that the inter-coach space aerodynamic noise varies approximately to the 7.7th power of the train speed. The observed high sensitivity serves as a motivation for the present investigation on elucidating the characteristics of noise emission at inter-coach space. As train speed increases, the effect of turbulent flows and vortex shedding is amplified, with concomitant increase in the aerodynamic noise. The turbulent flow field analysis demonstrates that vortex formation indeed causes generation of aerodynamic sound. For validation, numerical simulation and wind tunnel measurements are performed under identical conditions. The results show close correlation between the numerically derived and measured values, and with some adjustment, the results are found to be in good agreement. Thus validated, the numerical analysis procedure is applied to predict the aerodynamic noise level at inter-coach space. As the train gains speed, numerical simulation predicts increase in the overall aerodynamic sound emission level accompanied by an upward shift in the main frequency components of the sound. A contour mapping of the aerodynamic sound for the region enclosing the inter-coach space is presented.

• 한국추진공학회지
• /
• 제9권1호
• /
• pp.1-8
• /
• 2005

설계단계에서 수행되는 액체로켓엔진의 추력실 형상설계와 성능예측을 위하여 화학평형을 고려한 축대칭 압축성 해석코드를 개발하였다. 사용자의 편리함과 효율성에 중점을 두었으며, 형상파라미터의 입력값에 따라 자동으로 격자를 생성하고 연소실 조건은 추진제 조합, 연소압 그리고 혼합비를 지정함으로서 내부에서 계산하게 된다. 따라서 설계자는 추력실 형상 및 작동조건을 변화시켜 각각의 설계변수가 추력성능에 미치는 영향을 빠르고 손쉽게 파악할 수 있도록 하였다. CEA의 결과, JPL 노즐의 실험결과, 두 종류의 LRE 실제 엔진 자료, 그리고 KSR-III의 설계점 및 탈설계점 연소시험결과와 비교함으로서, 다양한 측면에서 해석코드의 정확도와 적용성을 평가하였다.

• 한국전산유체공학회지
• /
• 제12권4호
• /
• pp.7-13
• /
• 2007

Numerical analysis is carried out for combined heat transfer in an indirected NIR(Near Infrared Ray) heating chamber. Reynolds number and shapes of absorbed cylinder are known as important parameters on the combined heat transfer effects. Reynolds number based on the outer diameter of the cylinder is varied from $10^3$ to $3{\times}10^5$. Four difference heat transfer regimes are observed: forced convection and radiative heat transfer on the outer surface of the cylinder, pure conduction in the cylinder body, pure natural convection and radiation between lamp surface and inner surface of the cylinder, and radiation from the lamp. Flow and temperature characteristics are presented with iso-contour lines for the absorbed circular and elliptic cylinders to compare their differences. The convective and radiative heat transfer fluxes are also compared with different Reynolds numbers. As usual, Reynolds number is an important factor to estimate increasing convective heat transfer as it increases. The shape of absorbed cylinder results overall heat transfer rates remain unchanged.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.37-42
• /
• 2010

재생냉각식 액체로켓엔진의 예비 설계 단계에서 연소기 형상을 결정하기 위한 설계 방안을 제안하였다. CEA에서 예측된 연소 후 가스 물성치를 이용하여 로켓의 성능 및 재생냉각 성능을 계산하였다. 요구 추력, 연소실 압력, 주위 압력, 추진제 혼합비에 대해 1차원 관계식과 경험식으로 최적 유량과 연소기 성능을 예측하고, Rao 노즐 설계 기법을 활용하여 최종적으로 연소기 형상을 결정할 수 있는 방안을 제시하였다.

• 설비공학논문집
• /
• 제29권5호
• /
• pp.220-230
• /
• 2017

In this study we apply and compare a variety of numerical methods for calculating residence time distribution in decay tanks, a major design component in the for reducing N-16 radioactivity. Our research group has used a streamlined method using user-defined particle numbers. However, this streamlined method has several problems, including low exiting particle ratios, particle diminishing, and unphysical time distribution, among others. We utilize three numerical methods to establish residence time and time distribution (streamlined, discrete phase method [DPM], and user defined scalar [UDS]) and subsequently compare the averaged results of each. The three tests demonstrate the flow features within the decay tanks, which are then numerically simulated to enable comparison. We conclude that although each simulation predicts similar time averages, the UDS methodology provides a smoother time distribution and tracer contour plots at specific times.

• 한국철도학회논문집
• /
• 제7권3호
• /
• pp.193-199
• /
• 2004

Numerical analysis of aerodynamic characteristics was differently performed according to the running situation of the Korean Tilting Train eXpress(TTX) that would be introduced for an improvement in efficiency of the used railroad track. Fluent 6.0 was used for the analysis of Non-tilting case, Tilting case and Passing-by case with the model of TTX. As a result, the aerodynamic drag had little difference between Tilting and Non-tilting case. However, pressure contour under the train of Tilting case was not symmetry because the gap between a train and the ground was different at both sides. In Passing-by case attraction and counterattraction occurred alternately and affected to the opposite train. When two trains were side by side, the maximum attraction was generated especially. Through an analysis of pressure wave in tunnel a large variation of pressure was generated by the bluff nose of TTX. The results in this study would be good data for the aerodynamic characteristic on TTX and provide important information to judgment of running safety.

• Molecules and Cells
• /
• 제28권5호
• /
• pp.473-477
• /
• 2009

Previously, the 9-mer analog peptides, 9Pbw2 and 9Pbw4, were designed based on a defensin-like peptide, protaetiamycine isolated from Protaetia brevitarsis. In this study, antifungal effects of the analog peptides were investigated. The antifungal susceptibility testing exhibited that 9Pbw4 contained more potent antifungal activities than 9Pbw2. A PI influx assay confirmed the effects of the analog peptides and demonstrated that the peptides exerted their activity by a membrane-active mechanism, in an energy-independent manner. As the noteworthy potency of 9Pbw4, the mechanism(s) of 9Pbw4 were further investigated. The membrane studies, using rhodamine-labeled giant unilamellar vesicle (GUV) and fluorescein isothiocyanate (FITC)-dextran loaded liposome, suggested that the membrane-active mechanism of 9Pbw4 could have originated from the pore-forming action and the radii of pores was presumed to be anywhere from 1.8 nm to 3.3 nm. These results were confirmed by 3D-flow cytometric contour-plot analysis. The present study suggests a potential of 9Pbw4 as a novel antifungal peptide.

• Geomechanics and Engineering
• /
• 제14권2호
• /
• pp.131-139
• /
• 2018

The preparation of repeatable and uniformly reconstituted soil specimens up to the specified conditions is an essential requirement for the laboratory tests. In this study for large samples replication, the simultaneous usage of the traveling pluviation and curtain raining technique is used to develop a new method, called the curtain travelling pluviator (CTP). This simple and cost effective system is based on the air pluviation approach, whilst reducing the sample production time, can reproduce uniform samples with relative densities ranging from 25% to 96%. In order to investigate the resulting suitability and uniformity from the proposed method, a series of tests is performed. The effect of curtain traveling velocity, curtain width, drop height, and flow rate on the parameters of the sample is thoroughly investigated. Increase in the curtain velocity and drop height leads to the increase in relative density for the sand specimen. Increase in curtain width typically resulted in the reduction of relative density. Test results reveal that the terminal drop height for the sand specimen in this study is more than 500 mm. Relative density contour lines are presented that can be utilized in optimizing the drop height and curtain width parameters. Sample uniformity in the vertical and horizontal orientation is investigated through the sampling containers. Increasing relative density tends to result in the higher sample repeatability and uniformity.

• 한국환경과학회지
• /
• 제28권11호
• /
• pp.1047-1059
• /
• 2019

To address the increase of weather hazards and the emergence of new types of such hazards, an optimization technique for three-dimensional (3D) representation of meteorological facts and atmospheric information was examined in this study as a novel method for weather analysis. The proposed system is termed as "meteorological and air quality information visualization engine" (MAIVE), and it can support several file formats and can implement high-resolution 3D terrain by employing a 30 m resolution digital elevation model. In this study, latest 3D representation techniques such as wind vector fields, contour maps, stream vector, stream line flow along the wind field and 3D volume rendering were applied. Implementation of the examples demonstrates that the results of numerical modeling are well reflected, and new representation techniques can facilitate the observation of meteorological factors and atmospheric information from different perspectives.

• 소성∙가공
• /
• 제32권6호
• /
• pp.360-366
• /
• 2023

This study is concerned with the surface quality of products according to the material and coating condition of the forming tool in incremental sheet forming. Three forming tools, SKD11 with and without diamond-like-coating (DLC) and polymer tool tip, were used to form conical and pyramidal geometries to take into account the influence of friction between the forming tool and the sheet on the surface quality including geometric accuracy of deformed samples. Each test was performed using SUS304 with a thickness of 0.4 mm according to different incremental depths per lap of 0.5 mm, 1.0 mm, and 1.5 mm for the contour tool path, considering the increase in normal force which is associated with the frictional behavior during local deformation. The surface quality was then investigated through surface roughness measured with KEYENCE VR-6000 and relative strain distribution including deformed shape analyzed with ARGUS which is a non-contact optical strain measurement system. Differences between 3D CAD surfaces and captured geometry from experiments were evaluated to compare the effect of friction on geometric accuracy. From comparisons of experimental results, it was revealed that the polymer-based tool tip can improve surface quality and geometric accuracy by reducing the undesired material flow due to local friction in the increment sheet forming process.