• 한국전산유체공학회:학술대회논문집
• /
• 2007.04a
• /
• pp.79-82
• /
• 2007

The aerodynamic coefficients of Apollo capsule are calculated using a DSMC solver, SMILE, and the results agree very well with the data predicted by NASA. The aerodynamic characteristics of an orbital block which operates at high altitudes in the free molecule regime are also predicted. For the nominal flow conditions, the predicted aerodynamic force is very small since the dynamic pressure is extremely low. And the additional aerodynamic coefficients for the analysis of the attitude control are presented as the angle of attack and the side slip angle vary from $+45^{\circ}\;to\;-45^{\circ}$ of the nominal angle.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.6
• /
• pp.541-549
• /
• 2019

In the present study, we investigated planing forces of supercavitated bodies by using the supercavitation shape produced by the disk type cavitator. The cavity shapes are observed to find the immersion draft and planing angle when the stern of the supercavitated body is partially immersed in the water. To make the planing the angle-of-attack (AOA) of the supercavitated body is varied statically against the main flow and the planing tests are carried out for different body shapes that are changed systematically. The drag, lift and pitch moment acting on the body are measured to understand the relation between the planing force and the immersion draft of the supercavitated body. It is found that the planing force increased in general linearly with the immersion draft ratio and the planing angle is certainly not proportional to the immersion draft ratio.

• Journal of Power System Engineering
• /
• v.16 no.6
• /
• pp.24-29
• /
• 2012

In this study, the numerical simulation has been performed to investigate the hydrodynamic evaluation between double plate steel rudder and newly designed foil type rudder for small fishing boat. The simulations are carried out in 2 speed ranges with 7 variations of flow's angle of attack which is at intervals of about 5 degree respectively. As the well-known commercial code, FLUENT and CATIA are used as the solver. The simulation results show that new designed foil type rudder is better than conventional double plate rudder in terms of Lift and Drag of running boat in the water.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.3
• /
• pp.199-205
• /
• 2002

In this paper, the optimum shape and arrangement of ribs in the channel of a plate heat exchanger are studied. The following dimensionless geometric parameters of ribs are selected as design variables: rib height ($H_R$), angle of attack ($\beta$), rib pitch ($P_R$), rib distance (L) and aspect ratio of rib (AR). The optimization is performed by minimizing the objective function consisting of the Nusselt number and the friction factor. The optimal values of design variables are as follows: $H_R$=0.263, $\beta$=0.290, $P_R$=3.142, L: 3.954, AR=0.342. The pressure drop and the heat transfer of the optimum model, compared to those of the reference model, are increased by 15.1% and 41.6%, respectively.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.227-228
• /
• 2008

In the present paper, fowler flap was optimized to maximize the lift with response surface method. Leading edge shape and the gap between main airfoil and flap, were optimized and the aerodynamic characteristics was improved considerably. The optimized flap has more rounded leading edge and bigger gap. Before angle of attack, $10^{\circ}$, lift and drag are improved and the optimized flap shows similar aerodynamic characteristics to the original flap. The flow condition for optimization was angle of attack, $10^{\circ}$, Mach number, 0.2, flap deflection, $40^{\circ}$.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.227-228
• /
• 2008

In the present paper, fowler flap was optimized to maximize the lift with response surface method. Leading edge shape and the gap between main airfoil and flap, were optimized and the aerodynamic characteristics was improved considerably. The optimized flap has more rounded leading edge and bigger gap. Before angle of attack, $10^{\circ}$, lift and drag are improved and the optimized flap shows similar aerodynamic characteristics to the original flap. The flow condition for optimization was angle of attack, $10^{\circ}$, Mach number, 0.2, flap deflection, $40^{\circ}$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.8
• /
• pp.635-642
• /
• 2009

The three-dimensional turbulent wingtip vortex flows have been examined in the present study by using the commercial code FLUENT. The standard ${\kappa}-{\varepsilon}$ model is used as a closure relationship. The wing is constructed by using an elliptic body whose aspect ratio is 3.8 and the NACA 16-020 airfoil section. The simulations for various angle attack (${\alpha}=0^{\circ}$, $5^{\circ}$, and $10^{\circ}$) are carried out. The effect of Reynolds number is also investigated in this study. As the angle attack increases, the wingtip vortex becomes stronger. However, the relative vortex strength to inlet velocity decreases as Reynolds number increases.

• Journal of Industrial Technology
• /
• v.18
• /
• pp.335-341
• /
• 1998

A numerical investigation was performed to determine the effect of a Gurney flap on a NACA 23012 airfoil. A Navier-Stokes code, RAMPANT, was used to calculate the flow field about airfoil. The fully turbulent results were obtained using the standard $k-{\varepsilon}$ two-equation turbulence model. To provide a check case for our computational method, computations were performed for NACA 4412 airfoil which compared with Wedcock's experimental data. Gurney flap sizes of 0.5, 1.0, 1.5, and 2% of the airfoil chord were studied. The numerical solutions showed the Gurney flap increased both lift and drag. These results suggested that the Gurney flap served to increased the effective camber of the airfoil. But Gurney flap provided a significant increase in lift-to-drag ratio relatively at low angle of attack and for high lift coefficient. Also, it turned out that 0.5% chord size of flap was best one among them.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.17 no.2
• /
• pp.1-7
• /
• 2009

This paper illustrates how simulation modeling can be of substantial help in designing constructions in the vicinity of airport runway and presents results about the influence of aircraft wake vortices through computer simulation. The cross-wind energy dissipation rate is estimated from the Y-directional velocity spectrum for a sample in a real meteorological observation data. The eddy region about cross wind in the vicinity of airport runway is highly dependent on the height and shape of the buildings and the AOA of aircraft is greatly influenced by Y-directional velocity occurred by dint of separation region in runway.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.2
• /
• pp.297-306
• /
• 2019

Since the centrifugal force acts on the flow in the curved channel, a transverse water surface gradient occurs and the thalweg is biased toward the outer bank. The submerged vanes may be used to solve various engineering problems of the curved channels. In order to analyze the influence of an attack angle and the distance between the vane arrays on the river bed variation and the superelevation in a bend, movable bed hydraulic experiments were conducted in a $90^{\circ}$ curved rectangular channel of a small-size gravel bed. Installing the submerged vanes in the bend increases the maximum scour depth. But if vanes are installed in a uniform obtuse angle, the scour depth may be reduced. If the flow rate in the channel bend with vanes equals to the channel forming discharge, the location of the maximum scour depth moved to the downstream and the superelevation increased. However if the flow rate is smaller than that, the location of the maximum scour depth moved upstream and the superelevation decreased. The channel bed change and the superelevation due to the installation of the submerged vanes have been dependent on the interaction of the attack angle, the flow rate, and the distance between the arrays.